ScreenBeam MyWirelessTV 2 User Guide
- June 7, 2024
- ScreenBeam
Table of Contents
ScreenBeam My Wireless TV 2 User Guide
quick start guide
A. How My Wireless TV Works
MyWirelessTV allows video and audio to be sent from video source to the TV wirelessly. Therefore, you have the freedom to place the TV virtually anywhere within the home and enjoy live TV without the wiring mess.
Identify which source device you want to connect to the transmitter. Video
from that source device will then be transmitted to your receiver box(es).
Installation for the MyWirelessTV is easy. Both units come pre-paired
to work with each other. All you need to do is connect the cables according to
the diagram or, if you want, follow the detailed step-by-step instructions.
Note: Only use power adapter by Actiontec Electronics Inc., model number
WA-10P05FU.
B Setting up Transmitter and Receiver
Step 1A Select the source device (i.e. a cable/satellite set-top box or
Blu-ray player) you wish to transmit signal to the TV, and power off that
device. Get the wireless HD video transmitter unit from MyWirelessTV 2 Kit and
follow the steps below.
Note: If the transmitter and receiver are in the same room, you may skip
to Step 1C.
Step 1B (Optional) If the source device is previously connected to an HDTV, unplug the HDMI cable from the back of the source, then plug the free end of the HDMI cable into the HDMI port labeled Out-to-TV on the back of the transmitter
Step 1C Otherwise, get an HDMI cable from the MyWirelessTV 2 Kit. Plug one end into the HDMI Input port on the back of the transmitter.
Step 1D Plug the other end of the HDMI cable into the HDMI port on the source device.
Step 2A Get the power supply from the MyWirelessTV 2 Kit. Plug the smaller end of the power supply into the 5VDC port on the back of the transmitter.
Step 2B Plug the larger end of the power supply into a power outlet.
Step 2C Verify the POWER light on the transmitter is solid green.
Step 2D Now power on your video source device.
Note: The LINK light will blink.
Step 3A Get the wireless HD video receiver, HDMI cable and power supply. Go to the TV you want to connect.
Step 3B Plug one end of this HDMI cable into an HDMI port on the HDTV
Step 3C Plug the other end of the HDMI cable into the HDMI port labeled Out-to-TV on the back of the receiver
Step 3D Turn on the TV and switch the source to the HDMI input that the
receiver is connected to.
Step 4A Plug the smaller end of the power supply into the 5VDC port on
the back of the receiver.
Step 4B Plug the larger end of the power supply into a power outlet
Step 4C Make sure the power light on the receiver is solid green.
Step 4D Wait for a bit as the receiver connects to the transmitter. The LINK light should be solid green once they’re connected
D Troubleshooting
FREQUENTLY ASKED QUESTIONS
Do I have to connect a TV to the Transmitter’s HDMI Out-to-TV port?
No. This step is optional.
I’m not seeing video on the TV that’s connected to the transmitter. Check the
power and connection from the video source to the transmitter, and the
connection from the transmitter to TV. I’m not seeing video on the TV that’s
connected to the receiver. Check the power and connection from receiver to the
TV, and make sure the correct source input is selected on the TV. The audio
and video on the receiver’s TV seems slower than on the transmitter’s TV. This
is expected since the receiver receives AV transmission from the transmitter
over the air. How do I control the video source (e.g. cable/DirecTV box)
remotely? You need to use the same remote control. The control signal is
passed through the air from the MyWirelessTV 2 Receiver to the MyWirelessTV 2
Transmitter, and sent to the video source. The video quality is poor and
sometimes there’s no video display on the receiver’s TV. You may need to
adjust the orientation of the transmitter and receiver units, and direct them
to be facing each other. You can view the MyWirelessTV connection strength on
the Menu page of the receiver. To access the Menu page, press the MENU button
once on the receiver
I cannot control the source device with its remote control, via the
MyWirelessTV 2 receiver OR the source device is slow to respond to the remote
control. Make sure the IR blaster cable is connected to the transmitter’s
IR Transmit port, and the sensor is mounted directly on top of the source
device’s IR sensor window. Also make sure the receiver or the IR receiver
cable sensor is in line of sight of the remote control.
What is the MENU button on the receiver?
The MENU button provides access to the menu screen. You can view the device
firmware version, signal strength, or change the language for display and
video stream mode.
MyWirelessTV 2 Quick Start Guide
This Quick Start Guide will walk you through the easy steps to set up the MyWirelessTV 2 Kit.
A How MyWirelessTV Works B Setting Up Transmitter and Receiver C Setting Up IR Control D Troubleshooting
You will need the following items from your MyWirelessTV 2 kit:
- Wireless HD Transmitter •
- Wireless HD Receiver
- Two (2) Power Supplies
- Two (2) HDMI Cables
- IR Blaster Cable • IR Receiver Extension Cable
Telephone Technical Support
1-888-436-0657
Online Technical Support
https://retailsupport.screenbeam.com
©2021 ScreenBeam Inc. MyWirelessTV, MyWirelessTV2, ScreenBeam and the ScreenBeam logo are trademarks or registered trademarks of ScreenBeam Inc. in the U.S. and/or other countries. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. All other names or marks referenced are the names or marks of their respective owners. Product photo may differ from actual product, however functionality remains as stated above. Specifications subject to change without notice. 020921-v8
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>