YAMAHA CLIP-ON TUNER YTC10 Owner’s Manual

YAMAHA CLIP-ON TUNER YTC10

PRECAUTIONS

• Do not attempt to disassemble or modify in any way.
• Do not expose the device to rain, use it near water or in damp or wet conditions. Also, do not spill water or other fluids on the device.
• Never touch switches with wet hands.
• Follow the precautions below. Failure to do so might result in explosion, fire, overheating or battery fluid leakage.
  • Do not tamper with or disassemble batteries.
  • Do not dispose of batteries in fire.
  • Do not attempt to recharge batteries that are not designed to be charged.
  • Use the specified battery type only.
  • Always make sure the battery is inserted in conformity with the +/- polarity markings.
  • When the batteries run out, or if the device is not to be used for a long period of time, remove the batteries from the device.
• Keep batteries away from small children who might accidentally swallow them.
• If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns.
• When one of the following problems occur, immediately turn off the power switch and remove the battery from the device. Then have the device inspected by Yamaha service personnel.
  • It emits unusual smells or smoke.
  • Some object has been dropped onto the device.
  • The tuner suddenly stops working during use.
• Do not drop, hit, or use excessive force on the buttons or switches.
• Do not use thinner, alcohol, to clean the device.
• Do not use or store the device where it may be exposed to extreme temperatures (a location exposed to direct sunlight, near a heater, on a heat source, etc.) dusty locations, or places exposed to heavy vibration.
• Do not use the device in ways that exceed its intended use, excessively manipulate moving parts, and do not apply excessive force.
• Remove the clip from the device when not in use. Not doing so may result in spotting or discoloration. Be particularly careful using it on guitars with lacquer and other similar finishes.
• Make sure to discard used batteries according to local regulations.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

The Yamaha Clip-on Tuner YTC10 is a Vibration Sensor Tuner that tunes a musical instrument by sensing the vibration generated when a note is produced. When using Tuner for the first time after purchasing, gently pull out Insulating Sheet i to allow power to flow from the battery. The battery included with Tuner is a monitor battery, and its serviceable life may be shorter than specified.

NAMES OF PARTS

1. Power Button
2. Pitch Button
3. Sensitivity-Modulate Switch
4. LCD Display
   • Pitch Display
   • Note/Octave Display
5. Tuning Guide Lamp
6. Clip
7. Battery Tray
8. Insulation Sheet

TUNING METHOD

1. Attach Tuner to the musical instrument using Clip, and adjust the angle of Tuner to provide easy viewing.
   • Handle Tuner with care when attaching/detaching it or adjusting its angle. Applying undue force to it may cause damage.
   • For the movable range of Tuner, see the illustration c.
   • The Tuner body can be removed from the clip to reverse the setting position for easy viewing.
2. Press Power Button to turn on the power, and press Pitch Button to set the desired reference pitch.
   • The digits move quickly if the button is kept pressed.
3. Play the instrument to give a single note.
   • When having sensed the note (its vibration), Tuner indicates the octave and note closest to it on LCD Display. It also indicates discrepancy between the input note and the note shown on Display using Tuning Guide Lamp.
4. Tune the instrument until Tuning Guide Lamp at the center lights up in green.
   • When discrepancy between the input note and the note indicated on Display is within the range of 3 cents, Tuning Guide Lamp at the center will light up in green.

OTHER FUNCTIONS

• Sensitivity-modulate function: It eliminates background interference effectively.
  • HIGH mode is suitable for tuning in a quiet environment.
  • LOW mode is suitable for tuning in a noisy environment.
• Backlight: It lights up automatically with each input of a note or press of Pitch Button, and reduces its brightness gradually if Tuner is left untouched.
• Auto Power-Off Function: If no note input or Pitch Button operation is made for more than 5 minutes, Tuning Guide Lamp at the center flashes in green. If Tuner is left untouched further for 15 more minutes, it turns off automatically.
• Ambient sounds, etc. may also keep the tuner from automatically powering off.
  • Memory Backup Function: The reference pitch you have set is stored in memory, and will not be erased even if the power is turned off. If the battery is replaced with a new one, however, the reference pitch will return to the default setting of 440 Hz.

BATTERY CHANGE

When battery nears its end, LCD Display becomes dim, and the brightness of Tuning Guide Lamps is reduced. In that case, replace the battery with a new one immediately.

1. Turn off Tuner.
2. Remove the Tuner body from Clip.
3. While keeping the battery release knob on the rear of the Tuner body pressed with a tip of a ballpoint pen or the like, pull out Battery Tray.
4. Remove the old battery, insert a new one with (+) side up, and reset Battery Tray by pushing it into the Tuner body.
5. Press Power Button several times to confirm that Tuner operates normally.

• Be sure to use the specified battery (CR2032) only.
• When you decide not to use Tuner for a long time, remove the battery to prevent battery leakage.

CAUTIONS ON USING TUNER

• While Tuner is turned on, it may pick up noise from the surrounding environment or the hum noise generated by electric appliances, and show indications as if a note is played. This is not a malfunction.
• If the tuning is not successful, re-attach Tuner to such a position of the instrument that allows it to sense the vibrations more clearly.
• Please note that musical instruments that generate harmonic overtones or short sustaining tones may not be tuned accurately even though the note input to Tuner is within the tunable range.
• Moving Tuner beyond its movable range 3, moving it with excessive frequency, and applying undue force to it may cause damage to it.

SPECIFICATIONS

• Mode: Auto tuning
• Tunig Range: A0~C8
• Tuning Accuracy: 1 cent
• Pitch Shift: A4=415 Hz, 435 Hz~446 Hz
• Additional Functions: Sensitivity-modulate, backlight, auto power-off, memory backup
• Input Method: Vibration sensor
• Power Supply: Lithium battery CR2032 (3 V)
• Battery Life: approx. 30 hours (Depending upon usage and conditions)
• Overall Dimensions: 83.7(W) x 26.1(H) x 26.0(D) mm (including clip)
• Opening Range of Clip: 25 mm
• Weight: 50 g (including batteries)
• Accessories: Owner’s manual and lithium battery CR2032, 1 piece (monitor battery)
• The design and specifications are subject to change without prior notice for product improvement.

These symbols depicted in the Directive 2002/96/EC and 2006/66/EC indicate that used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment to avoid harmful effect on human health and environment, please contact your local municipality, your waste disposal service or the point of
sale where you purchased the items.

This product contains a battery that contains perchlorate material. Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

• This applies only to products distributed by Yamaha Canada Music Ltd. (class B)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>