PRO 1000 Vertical Non-Programmable Thermostat

TH1210DV1007/U,
TH1110DV1009/U,
TH1100DV1000/U

Operating Manual [pdf]: PRO 1000 Vertical Non-Programmable Thermostat

Installation Guide [pdf]: PRO 1000 Vertical Non-Programmable Thermostat

Installation Guide [pdf]: TH1000DV install

Installation Guide [pdf]: TH1100DH install

How do I turn on/off my heating/cooling on my TH1100DV/TH1110DV/TH1210DV

thermostat?

Locate the system Slider Switch labeled Heat Off Cool. Slide the switch to the desired setting and either manually adjust the arrows to the desired set point and press hold or establish a schedule for heating and cooling.

How do I access the installer setup (ISU) on the

TH1100DV/TH1110DV/TH1210DV thermostat?

Enter System Setup:

To enter system setup, press and hold both the up and down buttons until the display changes (approximately 5 seconds).

Changing Settings:

1. Press the up or down button to change the setting.
2. Press the up and down buttons simultaneously for one second to advance to the next function.
3. Press the RUN button to exit and save settings. Please note ISU changes when saved are permanently held in memory and will not be forgotten. If the thermostat is reverting to default programming troubleshoot the application.

TH1000DV install

TH1100DH install

How do I access the installer setup (ISU) on the

TH1100DV/TH1110DV/TH1210DV thermostat?

Enter System Setup:

To enter system setup, press and hold both the up and down buttons until the display changes (approximately 5 seconds).

Changing Settings:

1. Press the up or down button to change the setting.
2. Press the up and down buttons simultaneously for one second to advance to the next function.
3. Press the RUN button to exit and save settings. Please note ISU changes when saved are permanently held in memory and will not be forgotten. If the thermostat is reverting to default programming troubleshoot the application.

TH1000DV install

TH1100DH install

How do I turn on/off my heating/cooling on my TH1100DV/TH1110DV/TH1210DV

thermostat?

Locate the system Slider Switch labeled Heat Off Cool. Slide the switch to the desired setting and either manually adjust the arrows to the desired set point and press hold or establish a schedule for heating and cooling.

How do I fix a blank display on my TH1100DV/TH1110DV/TH1210DV thermostat?

If the thermostat is battery powered, check/replace your batteries. If the device is common wired, try and power it up with batteries. If that fails to power up the thermostat, you may need to involve a technician. If batteries do power up your common wired thermostat, check your breakers, furnace power switch, furnace door kill switch to insure your system is powered. If your system is fine, and the thermostat only works on batteries, you may need to involve a technician.

Why is my TH1100DV/TH1110DV/TH1210DV showing an error message HI? What

does it mean?

HI = The ambient temperature is above 122F (50 degrees C). Remember it can take several hours for a newly installed thermostat to normalize to room temperature. If the room temperature is lower than 122F (50 degrees C) and the thermostat is still displaying HI replace the thermostat.

Why is my TH1100DV TH1110DV TH1210DV showing an error message Lo Bat? What

does it mean?

Replace the Battery.

How do I fix a blank display on my TH1100DV/TH1110DV/TH1210DV thermostat?

If the thermostat is battery powered, check/replace your batteries. If the device is common wired, try and power it up with batteries. If that fails to power up the thermostat, you may need to involve a technician. If batteries do power up your common wired thermostat, check your breakers, furnace power switch, furnace door kill switch to insure your system is powered. If your system is fine, and the thermostat only works on batteries, you may need to involve a technician.

Why is my TH1100DV/TH1110DV/TH1210DV showing an error message E1? What

does it mean?

E1 = Replace the thermostat

Why is my TH1100DV/TH1110DV/TH1210DV showing an error message LO? What

does it mean?

LO – The ambient temperature is below 32F (0 degrees C) Remember it can take several hours for a newly installed thermostat to normalize to room temperature. If the room temperature is above below 32F (0 degrees C) and the thermostat is still displaying LO replace the thermostat.

Why is my TH1100DV/TH1110DV/TH1210DV showing an error message E2? What

does it mean?

E2 = Replace the thermostat.

SPECIFICATIONS

PRO 1000 Vertical Heat Non-Programmable Thermostat

Downloads

Operating Manual [pdf]: PRO 1000 Vertical Non-Programmable Thermostat

Installation Guide [pdf]: PRO 1000 Vertical Non-Programmable Thermostat

Installation Guide [pdf]: TH1000DV install

Installation Guide [pdf]: TH1100DH install

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>