VisionPRO 8000 with RedLINK Multistage Thermostat

TH8320R1003/U

Product Data [pdf]: VisionPRO 8000 with RedLINK

Product Information [pdf]:VisionPRO Series with RedLINK

TH8320WF
TH8320WF VisionPRO Wi-Fi 8000 User Manual

RTH8580WF
RTH8580WF VisionPRO Wi-Fi 8000 User Guide

TH8321WF
TH8321WF VisionPRO Wi-Fi 8000 User Guide

How do I change or reset the WiFi connection on my RTH8500WF WiFi Series

WiFi Touchscreen Programmable Thermostat?

Wi-Fi Reset:

A basic Wi-Fi reset can be completed by removing the thermostat face plate from the wall plate for 30 seconds and then reattaching it. The thermostat will then attempt to reconnect to the previously configured Wi-Fi network. To connect to a new Wi-Fi network:

TH8320WF / RTH8580WF – Proceed to step 1 to “forget” the current Wi-Fi configuration and connect to a new network. If your thermostat is already registered to your account, step 2 and step 3 are not required.

TH8321WF – On the thermostat screen, select Menu – WiFi setup. Press the down arrow until “Disconnect Wi-Fi network?” is displayed and select Yes.

Connecting your thermostat to Wi-Fi can be performed during the initial setup and configuration, or later at a time you choose.

Connecting to Wi-Fi – Initial Setup:

After the Configuration step during the initial install, you will be prompted to connect your VisionPRO Wi-Fi 8000 to your Home Wi-Fi.

The VisionPRO Wi-Fi 8000 (TH8321WF) can be connected to Wi-Fi on the thermostat itself after initial setup / configuration, or from the Menu > Wi- Fi Setup screen. After successful connection, register your product on the mytotalconnectcomfort.com/portal website to complete the process and control the thermostat remotely.

The VisionPRO Wi-Fi 8000 (RTH8580WF / TH8320WF) uses a 3-step connection and registration process

Step 1 – Connect your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Step 3 – Register with Honeywell / resideo. (Performed in the My Total Connect Comfort web portal)

Registration cannot be performed with the mobile app, currently only supported via the web portal

Step 1 – Connecting your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Once installed and configured, the (TH8320WF / RTH8580WF) thermostat will display “Wi-Fi Setup”. Open the Settings – Wi-Fi on your mobile device and connect to the Wi-Fi network named “NewThermostatxxxxxx”.

If your thermostat does not display Wi-Fi Setup remove the thermostat faceplate from the wall plate for 30 seconds and then reattach it. If Wi-Fi setup does not display, enter the Installer Setup (press the System button, then hold the center blank box at the bottom of the thermostat display for 5-10 seconds until the screen changes) and use the User / Installation Guide to navigate the settings to function 0890 . Make sure function 0890 is set to 1, then proceed to function 0900. Use the up or down arrow to change function 0900 function to 0 then press done. WiFi setup will then be displayed on the screen. Return to step 1.

TH8321WF – After initial configuration, you will be prompted to connect to WiFi. Select your Home Wi-Fi network, then enter the password on your thermostat screen

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Skip this step for the TH8321WF.

TH8320WF / RTH8580WF – After connecting to the thermostat Wi-Fi, open a web browser (Safari, Chrome, etc.) You should be automatically guided to a page labeled “Thermostat Wi-Fi Setup. If you are not automatically guided there, enter the IP address: 192.168.1.1 into the address bar on your browser to navigate there manually.

You should see your Home Wi-Fi network listed. Select it and enter your Wi-Fi password. After a brief connection period, your thermostat will display a “Connection Success” message. Reconnect your phone to your home wi-Fi network if your device does not reconnect automatically

If you do not see your home Wi-Fi network, refresh the list. If your Wi-Fi network is still not displayed, check the Trouble Connecting? / Wi-Fi network recommendations below.

Step 3 – Register at mytotalconnectcomfort.com/portal

Registration is completed at mytotalconnectcomfort.com/portal. Navigate to the page and create an account / login.

Select the “Add Device” icon and Input the MAC ID / CRC for your device. (MAC ID / CRC are located on your thermostat information card, on the back of the thermostat, or from the Menu > Equipment Status screen])

Complete the security check (if prompted) and follow the directions within the web portal to complete the registration.

How do I connect my RTH8500WF WiFi Series WiFi Touchscreen Programmable

Thermostat to WiFi and register it?

Connecting your thermostat to Wi-Fi can be performed during the initial setup and configuration, or later at a time you choose.

Connecting to Wi-Fi – Initial Setup:

After the Configuration step during the initial install, you will be prompted to connect your VisionPRO Wi-Fi 8000 to your Home Wi-Fi.

The VisionPRO Wi-Fi 8000 (TH8321WF) can be connected to Wi-Fi on the thermostat itself after initial setup / configuration, or from the Menu > Wi- Fi Setup screen. After successful connection, register your product on the mytotalconnectcomfort.com/portal website to complete the process and control the thermostat remotely.

The VisionPRO Wi-Fi 8000 (RTH8580WF / TH8320WF) uses a 3-step connection and registration process

Step 1 – Connect your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Step 3 – Register in the My Total Connect Comfort web portal

Registration cannot be performed with the mobile app, currently only supported via the web portal

Step 1 – Connecting your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Once installed and configured, the (TH8320WF / RTH8580WF) thermostat will display “Wi-Fi Setup”. Open the Settings – Wi-Fi on your mobile device and connect to the Wi-Fi network named “NewThermostatxxxxxx”.

If your thermostat does not display Wi-Fi Setup remove the thermostat faceplate from the wall plate for 30 seconds and then reattach it. If Wi-Fi setup does not display, enter the Installer Setup (press the System button, then hold the center blank box at the bottom of the thermostat display for 5-10 seconds until the screen changes) and use the User / Installation Guide to navigate the settings to function 0890 . Make sure function 0890 is set to 1, then proceed to function 0900. Use the up or down arrow to change function 0900 function to 0 then press done. WiFi setup will then be displayed on the screen. Return to step 1.

TH8321WF – After initial configuration, you will be prompted to connect to WiFi. Select your Home Wi-Fi network, then enter the password on your thermostat screen

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Skip this step for the TH8321WF.

TH8320WF / RTH8580WF – After connecting to the thermostat Wi-Fi, open a web browser (Safari, Chrome, etc.) You should be automatically guided to a page labeled “Thermostat Wi-Fi Setup. If you are not automatically guided there, enter the IP address: 192.168.1.1 into the address bar on your browser to navigate there manually.

You should see your Home Wi-Fi network listed. Select it and enter your Wi-Fi password. After a brief connection period, your thermostat will display a “Connection Success” message. Reconnect your phone to your home wi-Fi network if your device does not reconnect automatically

If you do not see your home Wi-Fi network, refresh the list. If your Wi-Fi network is still not displayed, check the Trouble Connecting? / Wi-Fi network recommendations below.

Step 3 – Register at mytotalconnectcomfort.com/portal

Registration is completed at mytotalconnectcomfort.com/portal. Navigate to the page and create an account / login.

Select the “Add Device” icon and Input the MAC ID / CRC for your device. (MAC ID / CRC are located on your thermostat information card, on the back of the thermostat, or from the Menu > Equipment Status screen])

Complete the security check (if prompted) and follow the directions within the web portal to complete the registration.

What are the features on my RTH8500WF WiFi Series WiFi Touchscreen

Programmable Thermostat?

The user guide for each thermostat has the full list of features / functions.

TH8320WF
TH8320WF VisionPRO Wi-Fi 8000 User Manual

RTH8580WF
RTH8580WF VisionPRO Wi-Fi 8000 User Guide

TH8321WF
TH8321WF VisionPRO Wi-Fi 8000 User Guide

Why am I getting a Wi-Fi Signal Lost message on my VisionPRO (TH8320WF or

RTH8580WF) thermostat?

If you’re getting a  Wi-Fi Signal Lost  message on your VisionPRO (TH8320WF or RTH8580WF) thermostat, it probably lost internet connection. Please follow the steps below to remedy the issue.

If your thermostat has lost wi-fi connection, you will be required to be on-location with the thermostat to reconnect it manually. For some users, a reconnection may be possible by remotely re-starting your wi-fi router. Check with your internet service provider for possible options.

To reconnect your device to Wi-Fi:

1. Make sure your router is online.
2. Go to your thermostat on the wall and remove it from its base.
3. Wait for 1 minute.
4. Add the thermostat back to its base on the wall.

If that doesn’t work, try the steps below:

Resetting Thermostat’s Wi-Fi Settings

1. Press  System.
2. You’ll see 5 blank boxes at the bottom of the screen. Press and hold  Middle Box  for about 5 seconds to change the screen.
3. Press the left set of arrows until the first number is  0900.
4. Press the right set of arrows until the second number is  0.
5. Press  Done  at the bottom-left corner.

Reconnecting Thermostat to Wi-Fi

6. Make sure  Wi-Fi Setup  is displayed at the top of the screen.
7. On a mobile device, view the list of available Wi-Fi networks.
8. Connect to  NewThermsotat_[series of numbers/letters]. This is a wifi connection between your phone and your thermostat – it is normal to receive a message that states “this connection has no access to the internet” – please dismiss the alert and continue. Do not allow the phone to change to another wi-fi connection until you have completed step 10. If you do not see the ”  NewThermsotat_[series of numbers/letters]”  network, remove the thermostat faceplate from the wall for 30 seconds and then reattach it and reattempt.
9. Wait for your browser to automatically open a setup screen. If this doesn’t happen, open a new browser on your mobile device and go to the web address  192.168.1.1.
10. Find the name of your home network and press  Red Button  below it.
11. Enter your home network’s password and press  Connect.

If you’re still having issues, please call Honeywell Customer Care at 1-800-633-3991.

Why is my thermostat not adjusting for Daylight Saving Time?

The VisionPRO thermostats have the ability to automatically adjust for Daylight Light Saving Time. Due to unforeseen changes in 2007 to the law modifying the beginning and the end of Daylight Saving Time, thermostats that were originally released do not have the updated dates to update on the correct dates. Production changes were made as soon as possible following the law change to add the ability to automatically adjust to the new date settings. DST We are unable to accommodate requests to trade-in an older version of the thermostats to new ones after the change in the law. In these instances, we recommend turning off the Daylight Saving Time automatic adjustment feature. This can be done in the user setup (instructions in the operating manual). Then the time should be adjusted in the fall and spring just like many other clocks in the home.

Why does the backup (auxiliary) heat stage come on immediately when I

raise the temperature setting?

The thermostat takes the temperature override as a need to reach the new temperature setting right away. It will run the backup heat only as long as necessary to reach new temperature setting.

Can the backlight be turned on all of the time?

It depends, if the thermostat is powered with a 24 Vac common it can be set to have continuous backlight. If the thermostat is battery powered, it cannot be set for continuous backlight. This is done by the installer in the installer setup settings of the thermostat. (Note, some models always require a common regardless of backlight setting).

How do I clean the thermostat screen?

Do not spray anything directly on the screen. Spray liquids onto a cloth, and then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers.
If you have a touchscreen, select “menu” then “clean screen”. The screen will remain locked for 30 seconds. After 30 seconds press “Done” to resume normal operation. This prevents accidentally changing the mode, set-point, etc. while cleaning

My thermostat does not show “Sched” or “Hold” buttons. Why?

If the thermostat is set for operation as a non programmable unit then it will not show Sched or Hold in the display. To check how the thermostat has been set up, please refer to the owner’s manual under Advanced Functions and refer to feature 0160.

How do I change the clock settings on the thermostat?

Newer Wi-Fi and some connected Honeywell thermostats, like the Lyric T5, VisionPro and certain Prestige models have a date option at the time setup that can include time adjustment for daylight savings time. If you have this feature, the thermostat will automatically update the time based upon the location that the device is registered in. If your thermostat does not have this auto-updating capability or the date is not enabled, you will need to manually adjust the time and date on your thermostat. Please follow the steps in the links bellow, according to the thermostat family model that you own.

8000 family

How do I change or reset the WiFi connection on my RTH8500WF WiFi Series

WiFi Touchscreen Programmable Thermostat?

Wi-Fi Reset:

A basic Wi-Fi reset can be completed by removing the thermostat face plate from the wall plate for 30 seconds and then reattaching it. The thermostat will then attempt to reconnect to the previously configured Wi-Fi network. To connect to a new Wi-Fi network:

TH8320WF / RTH8580WF – Proceed to step 1 to “forget” the current Wi-Fi configuration and connect to a new network. If your thermostat is already registered to your account, step 2 and step 3 are not required.

TH8321WF – On the thermostat screen, select Menu – WiFi setup. Press the down arrow until “Disconnect Wi-Fi network?” is displayed and select Yes.

Connecting your thermostat to Wi-Fi can be performed during the initial setup and configuration, or later at a time you choose.

Connecting to Wi-Fi – Initial Setup:

After the Configuration step during the initial install, you will be prompted to connect your VisionPRO Wi-Fi 8000 to your Home Wi-Fi.

The VisionPRO Wi-Fi 8000 (TH8321WF) can be connected to Wi-Fi on the thermostat itself after initial setup / configuration, or from the Menu > Wi- Fi Setup screen. After successful connection, register your product on the mytotalconnectcomfort.com/portal website to complete the process and control the thermostat remotely.

The VisionPRO Wi-Fi 8000 (RTH8580WF / TH8320WF) uses a 3-step connection and registration process

Step 1 – Connect your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Step 3 – Register with Honeywell / resideo. (Performed in the My Total Connect Comfort web portal)

Registration cannot be performed with the mobile app, currently only supported via the web portal

Step 1 – Connecting your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Once installed and configured, the (TH8320WF / RTH8580WF) thermostat will display “Wi-Fi Setup”. Open the Settings – Wi-Fi on your mobile device and connect to the Wi-Fi network named “NewThermostatxxxxxx”.

If your thermostat does not display Wi-Fi Setup remove the thermostat faceplate from the wall plate for 30 seconds and then reattach it. If Wi-Fi setup does not display, enter the Installer Setup (press the System button, then hold the center blank box at the bottom of the thermostat display for 5-10 seconds until the screen changes) and use the User / Installation Guide to navigate the settings to function 0890 . Make sure function 0890 is set to 1, then proceed to function 0900. Use the up or down arrow to change function 0900 function to 0 then press done. WiFi setup will then be displayed on the screen. Return to step 1.

TH8321WF – After initial configuration, you will be prompted to connect to WiFi. Select your Home Wi-Fi network, then enter the password on your thermostat screen

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Skip this step for the TH8321WF.

TH8320WF / RTH8580WF – After connecting to the thermostat Wi-Fi, open a web browser (Safari, Chrome, etc.) You should be automatically guided to a page labeled “Thermostat Wi-Fi Setup. If you are not automatically guided there, enter the IP address: 192.168.1.1 into the address bar on your browser to navigate there manually.

You should see your Home Wi-Fi network listed. Select it and enter your Wi-Fi password. After a brief connection period, your thermostat will display a “Connection Success” message. Reconnect your phone to your home wi-Fi network if your device does not reconnect automatically

If you do not see your home Wi-Fi network, refresh the list. If your Wi-Fi network is still not displayed, check the Trouble Connecting? / Wi-Fi network recommendations below.

Step 3 – Register at mytotalconnectcomfort.com/portal

Registration is completed at mytotalconnectcomfort.com/portal. Navigate to the page and create an account / login.

Select the “Add Device” icon and Input the MAC ID / CRC for your device. (MAC ID / CRC are located on your thermostat information card, on the back of the thermostat, or from the Menu > Equipment Status screen])

Complete the security check (if prompted) and follow the directions within the web portal to complete the registration.

How do I connect my RTH8500WF WiFi Series WiFi Touchscreen Programmable

Thermostat to WiFi and register it?

Connecting your thermostat to Wi-Fi can be performed during the initial setup and configuration, or later at a time you choose.

Connecting to Wi-Fi – Initial Setup:

After the Configuration step during the initial install, you will be prompted to connect your VisionPRO Wi-Fi 8000 to your Home Wi-Fi.

The VisionPRO Wi-Fi 8000 (TH8321WF) can be connected to Wi-Fi on the thermostat itself after initial setup / configuration, or from the Menu > Wi- Fi Setup screen. After successful connection, register your product on the mytotalconnectcomfort.com/portal website to complete the process and control the thermostat remotely.

The VisionPRO Wi-Fi 8000 (RTH8580WF / TH8320WF) uses a 3-step connection and registration process

Step 1 – Connect your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Step 3 – Register in the My Total Connect Comfort web portal

Registration cannot be performed with the mobile app, currently only supported via the web portal

Step 1 – Connecting your mobile device to the thermostat’s Wi-Fi network (NewThermostatxxxxxx)

Once installed and configured, the (TH8320WF / RTH8580WF) thermostat will display “Wi-Fi Setup”. Open the Settings – Wi-Fi on your mobile device and connect to the Wi-Fi network named “NewThermostatxxxxxx”.

If your thermostat does not display Wi-Fi Setup remove the thermostat faceplate from the wall plate for 30 seconds and then reattach it. If Wi-Fi setup does not display, enter the Installer Setup (press the System button, then hold the center blank box at the bottom of the thermostat display for 5-10 seconds until the screen changes) and use the User / Installation Guide to navigate the settings to function 0890 . Make sure function 0890 is set to 1, then proceed to function 0900. Use the up or down arrow to change function 0900 function to 0 then press done. WiFi setup will then be displayed on the screen. Return to step 1.

TH8321WF – After initial configuration, you will be prompted to connect to WiFi. Select your Home Wi-Fi network, then enter the password on your thermostat screen

Step 2 – Connect the thermostat to your home Wi-Fi (via an internet browser on your mobile device)

Skip this step for the TH8321WF.

TH8320WF / RTH8580WF – After connecting to the thermostat Wi-Fi, open a web browser (Safari, Chrome, etc.) You should be automatically guided to a page labeled “Thermostat Wi-Fi Setup. If you are not automatically guided there, enter the IP address: 192.168.1.1 into the address bar on your browser to navigate there manually.

You should see your Home Wi-Fi network listed. Select it and enter your Wi-Fi password. After a brief connection period, your thermostat will display a “Connection Success” message. Reconnect your phone to your home wi-Fi network if your device does not reconnect automatically

If you do not see your home Wi-Fi network, refresh the list. If your Wi-Fi network is still not displayed, check the Trouble Connecting? / Wi-Fi network recommendations below.

Step 3 – Register at mytotalconnectcomfort.com/portal

Registration is completed at mytotalconnectcomfort.com/portal. Navigate to the page and create an account / login.

Select the “Add Device” icon and Input the MAC ID / CRC for your device. (MAC ID / CRC are located on your thermostat information card, on the back of the thermostat, or from the Menu > Equipment Status screen])

Complete the security check (if prompted) and follow the directions within the web portal to complete the registration.

My thermostat shows humidity however I am unable to change it?

If the VisionPRO Thermostat does not allow you to change the humidity settings, then it is not setup for dehumidification or humidification control. In this case Honeywell recommends speaking to the installing contractor of the thermostat.

 Specifications

VisionPRO 8000 with RedlLINK Multistage Thermostat

Capabilities
Color| Arctic White
For Use With| Works standalone or with optional THM5421R1021 Equipment Interface Module and RedLINK accessories
Includes| VisionPRO® 8000 thermostat
Program Modes| 7-Day Programmable, Manual / Not Programmed
Utility Rewards| No
Display Type| Touch Screen
Fan Function| On, Auto, Circulating
Power Supply| Battery Powered, Hardwired
Product Height| 4.63 in
Product Length| 4.94 in
Product Width| 1.13 in
Warranty| 5 Years
Energy Star Certified| Yes
Stages| 3 Heat/2 Cool Heat Pumps, 2 Heat/2 Cool Conventional Systems, 4 Heat / 2 Cool Heat Pump with the EIM, 3 Heat / 2 Cool Conventional with the EIM

Downloads

Product Data [pdf]: VisionPRO 8000 with RedLINK

Product Information [pdf]:VisionPRO Series with RedLINK

TH8320WF
TH8320WF VisionPRO Wi-Fi 8000 User Manual

RTH8580WF
RTH8580WF VisionPRO Wi-Fi 8000 User Guide

TH8321WF
TH8321WF VisionPRO Wi-Fi 8000 User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>