MONSTER Airmars KT05 Bluetooth Wireless Earbuds Instruction Manual
- June 3, 2024
- Monster
Table of Contents
Airmars KT05 Bluetooth Wireless Earbuds
Instruction Manual
Airmars XKTQ5
BLUETOOTH WIRELESS HEADPHONES
INSTRUCTIONS MANUAL
Product parameters
- Transmission distance …………………………………………..10m
- Driver diameter……………………………………………………. 66mm
- Driver impedance……………………………………………………32Q415%
- Sensitivity………………………………………………………………. 105+43.0dB
- Frequency response range…………………………………………20H2-20kHz
- Battery capacity (charging case)…………………………………………..3,7V 320mAh
- Battery capacity (Headphone) ………………………………………………3.7V30mAh
- Charging time (charging case)……………………………………………..#15 hours
- Music playtime (headphone) ………………………………………………….4 hours
- Music playtime with charging case ……………………………………… *%24hours
Product parameters
• Transmission distance • Driver diameter • Driver impedance • Sensitivity •
Frequency response range
• Battery capacity (charging case) • Battery capacity (Headphone) • Charging
time (charging case) • Music playtime (headphone) • Music playtime with
charging case
10m 06mm 320±15% 105±3.0dB 20Hz-20kHz 3.7V 320mAh 3.7V 30mAh z1.5 hours z4
hours r424 hours
Packing list
| Headphone 2
---|---
| Silicone Ear Tips S 2
Silicone Ear Tips M (installed) 2
Silicone Ear Tips L 2
| Instructions Manual 1
| Charging Case 1
| Type-C Charging Cable *1
Product Schematic Description
Charge the charging case
Connect the charging case to the 5V power adapter with Type-C charging
cable.
Rated input: 5V===30mA(Headphone) Rated input: 5V===300mA (charging case)
Indicator guide
| Mode | Describe | Sound prompt |
|---|---|---|
| Power On | Headphone ice blue indicator lights up for 2 seconds | “Power on” |
| Power Off | Headphone White indicator lights up for 2 seconds | “Power off” |
| Pairing | Headphone ice blue and white indicator flashes alternatively |
“Pairing”
Connected| Headphone White indicator lights up once| “Connected”
Disconnected| Headphone ice blue and white indicator flashes alternatively|
“Disconnected”
Low Battery| | “Battery low”
Headphones placed in
charging case| When the headset is charged, the white light is on for a long
time and goes out after it is fully charged|
Charging case low power| LED indicator flashes quickly|
Charging case charging| LED indicator flashes slowly|
Charging case fully charged.| LED indicator light up for 10 seconds|
Product operating instructions
-
Power on
Open the cover of the charging case and take out the headphones, the headphones will turn on automatically. -
Power off
Method 1 : put the headphone/s back to the charging case,and the headphone/s will power off automatically Method 2: after disconnected from the Bluetooth device for 3 minutes. -
Pairing
Method 1 : open the cover of the charging case and take out the headphones. Method 2: search and click for “Monster Airmars XKT05″ on the Bluetooth list of the smart device,and when connection is successful,”Connected” will be heard.
- Headphones will try reconnecting to the device within 3 minutes when connection is lost .
Note: Fully charge the headphones and power off before an intended not- in-use period. Unplug the charging cable after charging.
Operation
Restore fectory settings
Either headphones is not connected to the Bluetooth device when turned on, click the MFB 5 times to clear the previous pairing information and turn off.
Precautions
- Open the cover of the charging case, take out the headphones and the headphone will power on automatically, then connect with the paired device.After placing the headphones in the charging case, they will turn off and automatic charging will start when the cover is closed.
- Charging every 15 days will extend battery life when not in use often. Cleaning off dirt on the charging contacts by cotton swabs with alcohol will maintain a good contact for charging. 3. Keep battery (battery pack) away from inflammables or excessive heat such as direct sunlight. 4. Intermittent is normal during playback for wireless products due to environmental factors, device brand, users’ behavior, etc.
Warnings
- Do not use headphones at high volume for an extended period of time.
- Keep the headphones away from dust and water.
- Do not disassemble the headphones and accessories, otherwise warranty will be voided.
- Keep headphones away from any impact or vibration.
- Do not use any chemical solvents or cleaning agent on the headphones.
| Name of the Parts | Hazardous Substances |
|---|---|
| Pb | Hg |
| Housing | 0 |
| Loudspeakers | o |
| PCBA | X |
| Accessories | X |
This table is compiled according to SJ/T 11364.
0:Indicates that this hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in GB/T 26572.
X: Indicates that this hazardous subatance contained in at least one of the
homogeneous materials used for this part is above the limit requirement in
GB/T 26572.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID 2A8PV-OSMXKTO5
Environment Friendly Use Period (EFUP)
This logo refers to the period (10 years) during which the hazardous
substances in electronic and electrical produsts will not leak or mutate so
that the use of these [substances] will not result in any severe environmental
pollution, any bodily injury or damage to any assets.
Warranty Service
Dear user, this warranty card is the proof of your future warranty application, please cooperate with the seller to fill it out and keep it for future use!
User information
User name| | Email|
Contact number| | Postal code|
Mailing address| | |
Product information
Product name| | Product number|
Product barcode / Serial number / Batch number| |
Vendor information
Name|
Address|
Contact number| | Postal code|
Sales date| | Invoice number|
Remark|
MONSTER
Certificate of Approval………………………………….
Product No……………………………………………………..
Production Time Ps,………………………………………..
QC:…………………………………………………………………