ROWENTA RO1755GA Compacteo Cordless Vacuum Cleaner User Manual

: June 5, 2024
: Rowenta

Table of Contents

SAFETY RECOMMENDATIONS
DESCRIPTION
BEFORE USING FOR THE FIRST TIME
USE
CLEANING AND MAINTENANCE
TROUBLESHOOTING
THE ACCESSORIES*
ENVIRONMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

902444B

| ROWENTA RO1755GA Compacteo Cordless Vacuum Cleaner - fig
1 | ROWENTA RO1755GA Compacteo
Cordless Vacuum Cleaner - fig 2
---|---|---

SAFETY RECOMMENDATIONS

For your safety, this appliance complies with all enforceable standards and regulations (Low Voltage Directives, Electromagnetic Compatibility, Environment, etc.).
CONDITIONS FOR USE
Your vacuum cleaner is an electrical device: it must be used under normal conditions of use.
Use and store the appliance out of reach of children. Never leave the appliance operating without supervision.
Do not hold the tool attachment or tube close to your eyes and ears.
Do not use your vacuum cleaner on the wet surfaces, water or liquids of whatever kind, hot substances, extremely fine substances (plaster, cement, ash…), large sharp objects (broken glass), or products that are harmful (solvents, paint strippers…), corrosive (acids, cleaning fluids…), flammable and explosive (petroleum or alcohol-based).
Never immerse the appliance in water, do not spray water onto the appliance, and do not store it outdoors.
Do not use the appliance if it has fallen and has visible damage or appears to be working abnormally. In this case, do not open the appliance, but send it to the closest Approved Service Centre or contact the Rowenta Consumer Service (see contact information on the last page).

POWER SUPPLY

Check that the power voltage for your vacuum cleaner corresponds to that of your main installation. You will find this information on the bottom of the appliance.
Disconnect the appliance by removing the plug from the wall socket: – immediately after use, – each time you change the accessory, – before each cleaning, maintenance and filter change operation.
Do not use the appliance: – if the power cord is damaged. To avoid danger, the whole reel and power cord unit of your vacuum cleaner must be replaced by a Rowenta Approved Service Centre.

REPAIRS
Repairs are to be performed only by specialists with original spare parts.
Repairing an appliance oneself may constitute a danger to the user.

DESCRIPTION

a – Horizontal parking
b – Vertical parking
On/Off Pedal
Electronic power regulator*
Cord winder pedal
Bag full light
Air outlet grid
a – Vertical carry grip
b – Horizontal carry grip
c – Shoulder strap storage fixture
Bag compartment
Lid
Suction opening
a – Lid opening flap
b – Bag presence detector
Motor protection grid
Microfilter* (ref. ZR0039 01)
a – HEPA filter cassette (ref. ZR0041 01), suitable for paper bags
b – HEPA filter cassette (ref. ZR0042 01), suitable for textile bags
Your vacuum cleaner is fitted with either a microfilter or a HEPA filter cassette*.
Bag support for Wonderbag Compact (17c), paper bag (17a) or textile bag* (17b)
Bag support runners Standard accessories:
Bags
a – Paper bag (ref. ZR0039 01/ZR0041 01)
b – Textile bag
c – Wonderbag Compact bag* (ref. WB305120 / WB305130 / WB305140)
Flexible hose with grip and mechanical power regulator
Telescopic tube*
Tubes*
Hardfloor tool*
All floor tool
Furniture tool*
Slot tool attachment convertible into a brush*
Turbobrush *
Mini turbo brush*
Shoulder strap*
Shoulder strap cover*

BEFORE USING FOR THE FIRST TIME

UNPACKING

Unpack your appliance, keep your warranty card and read the instructions for use carefully before using your appliance for the first time.
TIPS AND PRECAUTIONS
Before each use, the cord should be unwound completely.
Make sure that it does not get stuck or go against any sharp objects.
If you are using an extension cord, make sure it is in perfect condition and that it suitable for the power of your vacuum cleaner.
Your vacuum cleaner is fitted with a device to protect against the motor overheating. In certain cases, (using the flexible hose on chairs, etc.) the device is triggered and the appliance may make an unusual noise. This is of no consequence.
Do not move the vacuum cleaner by pulling on the cord, the appliance must be moved by its carrying handle.
Do not use the cord to lift the appliance.
Never unplug the appliance by pulling on the cable.
Never operate without a vacuum bag and without a filtration system: microfilter or HEPA filter cassette.
Ensure that the filter (13 or 14a and 14b) is firmly in place.
Use only original Rowenta bags and filters.
Use only original Rowenta accessories.
In the event that you find it difficult to obtain accessories and filters for this vacuum cleaner, contact the Rowenta customer service (see contact information on the last page).
Stop and unplug your vacuum cleaner after each use.
Always stop and unplug your vacuum cleaner before maintenance or cleaning.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

USE

ASSEMBLAGE OF THE PARTS OF THE APPLIANCE

Push the flexible hose (18) into the suction opening (10) until it clicks – fig. 1.
To remove it, press the clips on the hose nozzle and pull – fig. 2.
If your vacuum cleaner is equipped with the telescopic tube (19): push the adjustment knob forward, pull the desired tube length out then release the button to lock – fig. 3a. Otherwise, assemble the two tubes (20), turning them slightly – fig. 3b.
Fit the desired accessory to the end of the tube:
– For rugs and carpets: Use the all floor tool attachment (22) in retracted brush position – fig. 4.
– For parquets and smooth floors: Use the all floor attachment (22) in brush position – fig. 4. or use the hardfloor tool (21) directly.
– For corners and areas which are difficult to reach: use the slot tool attachment convertible into a brush (24) in the flat tool attachment position.
– For furniture: use the slot tool attachment convertible into a brush (24) or the furniture nozzle (23).
Your appliance is equipped with a strap * (27), which allows you to carry it on your shoulder.
– To unlock the strap, remove the covers on either side of the handle by giving them a quarter turn in the direction opposite to the arrow – fig. 5a.
– To replace it, do the reverse: replace the covers on either side of the handle by giving them a quarter turn in the direction of the arrow – fig. 5b, until they click, and then place the shoulder strap in its storage housing (7b).

Please note!
Be sure to observe the assembly direction ( ) indicated close to the on/off pedal (2).
Always stop and unplug your vacuum cleaner before changing accessories.
CONNECTING THE CORD AND STARTING THE APPLIANCE
• Unwind the power cord completely, plug your vacuum cleaner in – fig. 6 and press the On/Off pedal (2) – fig. 7.
• Set the suction power:
– using the electronic power regulator (3): turn the switch on the electronic regulator to set the suction
power: towards maximum position for floors and minimum position for furniture and fragile fabrics – fig. 8.
– with the mechanical power regulator on the grip: open the slider on the grip to manually reduce suction power, e.g.: on fragile surfaces… – fig. 9.
STORING AND TRANSPORTING THE APPLIANCE

After use, stop your vacuum cleaner by pressing the On/Off pedal (2) and unplug it – fig. 10. Wind the power cord by pressing the cord winder pedal (4) – fig. 11.
Upright, place the tool attachment (22) in its housing under the appliance (1b) – fig. 12.
Horizontal, place the tool attachment (22) in its housing at the back of the appliance (1a) – fig. 13.
Carry your vacuum cleaner easily using its carry handles (7a or 7b) or its shoulder strap* (27).

CLEANING AND MAINTENANCE

Important: Always stop and unplug your vacuum cleaner before maintenance or cleaning.
CHANGING BAG

The bag full light (5) indicates that the bag is full or saturated.
If you notice that your appliance is becoming less efficient, set it to maximum power and hold the nozzle up above the ground. If the light stays red, replace the bag.
Remove the flexible hose (18) from the suction opening (10) – fig. 2
Open the lid (9) of your vacuum cleaner – fig. 14. a) If your vacuum cleaner is equipped with a paper bag (17a) or a Wonderbag Compact (17c) :
Remove the bag support (15) from the bag compartment (8) – Fig. 15a, then remove the paper bag (17a) or the Wonderbag Compact (17c) from its support by sliding it along the runners (16) – Fig. 15b.
Dispose of the paper bag or the Wonderbag Compact in a dustbin – Fig. 15c
Position a new paper bag or a new Wonderbag Compact on the support – Fig. 15d. Place it in the compartment – Fig. 15e
Check that the bag is correctly placed before closing the cover (9).
*b) If your vacuum is fitted with a textile bag :**
Remove the bag support (15) from the bag compartment (8) – fig. 16a, then remove the textile bag (17b) from its support (15) by sliding it along its runners (16) – fig. 16b. • Open the bag with the zip – fig. 16c, then empty it over a dustbin – fig. 16d.
Clean the bag under running water – fig. 16e.
Allow to dry for at least 24 hours (only put the bag back into position when it is completely dry) – fig. 16f.
Ensure that the zip is properly closed – fig. 16g before putting it back in position.

*CHANGE THE MICROFILTER (ref: ZR0039 01) OR THE HEPA FILTER CASSETTE (ref: ZR0041 01) Microfilter (ref: ZR0039 01)**

Open the lid (9) of your vacuum cleaner – fig. 14.
Open the motor protection grid (12) – fig. 17a.
Remove the microfilter * (13) – fig. 17b.
Discard the microfilter * (13) into a dustbin – fig. 17c and replace it with a new microfilter (ref. ZR0039 01• Place the pins in the notches – fig. 17d.
Lock the microfilter * behind the engine protection grid (12) – fig. 17e.
Make sure the microfilter* (13) is properly in position before closing the lid (9).

*HEPA FILTER CASSETTE (REF: ZR0041 01)*
Important: Replace the HEPA filter cassette ZR0041 01 every 6 months (depending on the frequency of use).

Open the lid (9) of your vacuum cleaner – fig. 14.
Remove the HEPA filter cassette* (14a) – fig. 18a – 18b.
Throw the cassette into the dustbin – fig. 18c.
Place the pins in the notches – fig. 18d.
Lock the new HEPA filter cassette* (14a) (ref. ZR0041 01) in its housing – fig. 18e.
Make sure the HEPA filter cassette* (14a) is properly in position before closing the lid (9).

*CLEANING THE HEPA FILTER CASSETTE (ref: ZR0042 01)*
Please note! This cleaning operation is reserved exclusively for the HEPA filter cassette ref: ZR0042 01.

Open the lid (9) of your vacuum cleaner – fig. 14.
Remove the HEPA filter cassette* (14b) – fig. 19a – 19b.
Tap the HEPA filter cassette* (14b) over a dustbin – fig. 19c.
Then hold it under running water – fig. 19d, and allow to dry at least 24 hours – fig 19e.
Ensure that the HEPA filter cassette * (14b) is completely dry before replacing it.
Place the pins in the notches – fig. 19f.
Lock the HEPA filter cassette* (14b) (Ref: ZR0042 01) in its housing – fig. 19g.
Make sure the HEPA filter cassette* (14b) is properly in position before closing the lid (9).

CLEANING THE VACUUM CLEANER

Wipe the body of the vacuum cleaner and accessories with a soft damp cloth, then dry.
Wipe the lid with a dry cloth – fig. 20.
Do not use detergents or any corrosive or abrasive products.

TROUBLESHOOTING

Important: As soon as your vacuum cleaner stops performing efficiently, and before making any checks, stop it by pressing on the On/Off pedal.
IF YOUR VACUUM CLEANER DOES NOT START

The appliance is not powered: make sure the appliance is properly connected.
IF YOUR VACUUM CLEANER DOES NOT SUCK
An accessory or the hose is blocked: unblock the accessory or hose.
The lid is not properly closed: check that the bag is properly in position and close the lid.
IF YOUR VACUUM CLEANER IS NOT SUCKING PROPERLY OR IS MAKING A WHISTLING NOISE
An accessory or the hose is partially blocked: unblock the accessory or hose.
The bag is full or saturated by fine dust: replace the paper bag (17a) or the Wonderbag Compact (17c), or empty the textile bag* (17b).
The bag full light is red: the filtration system is saturated.
*– HEPA cassette:* change the HEPA cassette (14a) (ref. ZR0041 01) and replace it in its housing or wash the HEPA filter cassette* (14b) (ref. ZR0042

according to the procedure.
*– Microfilter:* Remove the microfilter and replace it with a new one (ref. ZR0039 01).

The electronic power regulator is in the minimum position: increase the power using the electronic power regulator (unless you are cleaning fragile fabrics).
The mechanical power regulator on the grip is open: close the mechanical power regulator.

IF THE BAG IS FULL LIGHT STAYS RED

The bag is saturated: replace the paper bag (17a) or the Wonderbag Compact (17c), or empty the textile bag* (17b).
IF THE LID DOES NOT CLOSE (bag presence detector 11b activated)
Check the presence of the bag or that it is in the correct position.
IF THE TOOL ATTACHMENT IS DIFFICULT TO MOVE
Open the regulator slot on the grip or decrease power.
IF THE POWER CORD DOES NOT WIND UP COMPLETELY
The cord slowed down as it was winding up: bring the cord back out and press the cord winder pedal again.
IF YOUR VACUUM CLEANER STOPS WHILE IN OPERATION
The overheating protective device has been triggered. Check that the tube and the pipe are not blocked or that the bag or filter are not full. Leave to cool down for 30 minutes before using the vacuum cleaner again.
If the problem persists, take your vacuum cleaner to the nearest Rowenta Approved Service Centre. See the list of Rowenta Approved Service Centres or contact the Rowenta Consumer Service (see contact information on the last page).

WARRANTY

This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.
Read the instructions for use carefully before using your appliance for the first time: in the event of any use that does not comply with the instructions, Rowenta shall accept no liability.

THE ACCESSORIES*

**ACCESSORIES*| USE| FITTING OF THE ACCESSORY| WHERE TO BUY IT**
---|---|---|---
Furniture tool| To clean furniture.| Fit the furniture tool to the end of the tube.| Rowenta Approved Service Centres (see list of addresses attached).
Slot tool attachment convertible into a brush| For corners and areas which are difficult
to reach.| Fit the slot tool attachment convertible into a brush to the end of the grip or the tube.| Rowenta Approved Service Centres (see list of addresses attached).
Hardfloor tool| For fragile floors.| Fit the hard floor tool to the end of the tube.| Rowenta Approved Service Centres (see list of addresses attached).
Mini turbo brush| For deep cleaning of upholstery fabrics.| Fit the mini turbo brush to the end of the tube.| Rowenta Approved Service Centres (see list of addresses attached).
Turbobrush| To remove threads and animal hair embedded in rugs and carpets.| Fit the turbo brush to the end of the tube.| Rowenta Approved Service Centres (see list of addresses attached).

ENVIRONMENT

In accordance with existing regulations, any appliance that is out of service must be rendered perma- nearly inoperable: unplug and cut the power cord before discarding the appliance.
Environmental protection first!
Your appliance contains valuable materials which can be recovered or recycled.
→ Take it to a collection point or an approved service centre so that it can be recycled.