KitchenAid KSM110 Stand Mixer Instruction Manual

: June 17, 2024
: KitchenAid

————————————————

K45 Series

KSM45–KSM200 Series

PARTS AND FEATURES

PARTS AND ACCESSORIES

Speed control
Motor head
Attachment hub
Beater shaft
Flat beater
Bowl
**Flex Edge beater***
Dough hook
Wire whip
**Pouring shield***

*Accessory sold separately

STAND MIXER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING:’ These words mean:

Kitchenaid - Danger You can be killed or seriously injured if you don’t immediately follow instructions.

Kitchenaid - Warning 2 You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

Read all instructions.
To avoid risk of electrical shock, do not put Stand Mixer in water or other liquid.
Close supervision is necessary when any appliance is used by or near children.
Unplug the Stand Mixer from outlet when not in use, before putting on or taking off parts, and before cleaning.
Avoid contacting moving parts. Keep hands, hair, and clothing, as well as spatulas and other utensils, away from beater during operation to reduce the risk of injury to persons and/or damage to the Stand Mixer.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest Authorized Service Facility for examination, repair, or adjustment.
The use of accessories not recommended or sold by KitchenAid may cause fire, electric shock, or injury.
Do not use the Stand Mixer outdoors.
Do not let the cord hang over the edge of table or counter.
Do not let the cord contact hot surfaces, including the stove.
Remove the flat beater, wire whip, or spiral dough hook from the Stand Mixer before washing.

SAVE THESE INSTRUCTIONS

This product is designed for household use only.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Voltage: 120 V

Frequency: 60 Hz

Wattage: 275 Watts MAX for models
K45, KSM45-KSM80
300 Watts MAX for models
KSM85-KSM110
325 Watts MAX for models
KSM120-KSM200

NOTE: The power rating for your Stand Mixer is printed on the serial plate.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

The maximum rating is based on the attachment that draws the greatest load (power). Other recommended attachments may draw significantly less power.

USING THE STAND MIXER

CHOOSING THE RIGHT ACCESSORY

ACCESSORY

| USE TO MIX|

DESCRIPTION

---|---|---
FLAT BEATER
**FLEX EDGE BEATER***

|

Normal to heavy mixtures

| Cakes, creamed frostings, candies, cookies, biscuits, pie pastry, meatloaf, mashed potatoes
WIRE WHIP

|

Mixtures that need air incorporated

| Eggs, egg whites, heavy cream, boiled frostings, sponge cakes, mayonnaise, some candies
DOUGH HOOK

|

Mixing and kneading yeast doughs

| Breads, rolls, pizza dough, buns

SPEED CONTROL GUIDE

NOTE: The speed control can be set between the speeds listed in the chart to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when preparing yeast doughs as this may cause damage to the Stand Mixer.

SPEED

| ACCESSORY| ACTION| DESCRIPTION
---|---|---|---

STIR

| | STIR| For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter and to add liquids to dry ingredients. Do not use Speed 1 to mix or knead yeast doughs.

2

|

| SLOW MIXING| For slow mixing, mashing, faster stirring. Use to mix and knead yeast doughs, heavy batters and candies, start mashing potatoes or other vegetables, cut shortening into flour, mix thin or splashy batters.

4

|

| MIXING, BEATING| For mixing semi-heavy batters, such as cookies. Use to combine sugar and shortening and to add sugar to egg whites for meringues. Medium speed for cake mixes.

6

|

| BEATING, CREAMING| For medium fast beating (creaming) or whipping. Use to finish mixing cake, doughnut, and other batters. High speed for cake mixes.

8

| | FAST BEATING, WHIPPING| For whipping cream, egg whites, and boiled frostings.

10

| | FAST WHIPPING| For whipping small amounts of cream, egg whites, or for final whipping of mashed potatoes.

NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

ASSEMBLING THE STAND MIXER

1 Check to be sure that the Stand Mixer is unplugged, and the speed control is turned to “0”.

2 Raise the motor head: Slide the locking lever to the unlock position and lift the motor head.

NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

3 Attach the bowl: Place the bowl on the bowl clamping plate and gently turn it in a clockwise direction to lock it into place.

4 Attach any accessory: Slip the accessory onto the beater shaft and press upward as far as possible. Turn the accessory counterclockwise to hook the accessory over the pin on the shaft.

5 Lower the motor head until it is all the way down, then slide the locking lever to the lock position. Before mixing, test lock by attempting to raise motor head.

(OPTIONAL) To adjust beater to bowl clearance: Tilt the motor head back; then, using a flat-head screwdriver, turn the screw slightly counterclockwise (left) to raise the beater, or clockwise (right) to lower the beater. Adjust the beater so that it just clears the surface of the bowl. If you overadjust the screw, the bowl lock lever may not lock into place.

*(OPTIONAL) Place the pouring shield:** Slide the pouring shield from the front of the Stand Mixer over the bowl until the pouring shield is centered. The bottom rim of the pouring shield fits inside of the bowl. The pouring chute will be just to the right of the attachment hub as you face the Stand Mixer.

IMPORTANT: Your Stand Mixer is adjusted at the factory so that the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can easily correct the clearance.

NOTE: When properly adjusted, the flat beater will not strike on the bottom or sides of the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the bowl, coating may wear off the beater or wires on the whip may wear.

OPERATING THE STAND MIXER

NOTE: The Stand Mixer may warm up during use. Under heavy loads with extended mixing time, the top of the unit may become hot. This is normal.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Injury Hazard

Unplug mixer before touching beaters.
Failure to do so can result in broken bones, cuts, or bruises.

1 Plug the Stand Mixer into a grounded 3 prong outlet. Always set the speed control lever on lowest speed to start, then gradually increase speed to avoid splashing ingredients. See the “Speed control guide” to select the best speed for your recipe.

NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

2 Do not scrape the bowl while the Stand Mixer is operating. The bowl and beaters are designed to provide thorough mixing without frequent scraping. Scraping the bowl once or twice during mixing is usually sufficient.

(OPTIONAL) Pour ingredients into the bowl through the pouring chute.

NOTE: The pouring shield* can be used to avoid ingredients splashing out of the bowl when mixing as well as to easily pour ingredients in the bowl while mixing.

DISASSEMBLING THE STAND MIXER

1 Raise the motor head: Check to be sure that the Stand Mixer is unplugged, and the speed control is turned to “0”; then, slide the locking lever to the unlock position and lift the motor head.

*(OPTIONAL) Remove the pouring shield:** Lift the front of the pouring shield clear of the rim of the bowl, and pull away from the Stand Mixer.

2 Remove the accessory: Press the accessory upward as far as possible, then turn the accessory clockwise and pull it away from the beater shaft.

3 Remove the bowl: Gently turn the bowl counterclockwise to release it from the bowl clamping plate.

OPTIONAL ATTACHMENTS

KitchenAid offers a wide range of optional attachments such as the spiralizer, pasta cutters, or food grinder that may be attached to the Stand Mixer attachment power hub as shown here.

1 Check to be sure that the Stand Mixer is unplugged and the speed control is turned to “0”.

2 Turn the attachment knob counterclockwise to remove attachment hub cover.

3 Insert attachment into attachment hub, making certain that attachment power shaft fits into the square attachment hub socket. It may be necessary to rotate the attachment back and forth. When it is in the proper position, the pin on the attachment will fit into the notch on the hub rim.

4 Tighten the attachment knob by turning it clockwise until the attachment is completely secured to the Stand Mixer. See the Instructions manual that came with your attachment for detailed directions on using the attachment.

TIPS FOR GREAT RESULTS

EGG WHITES

Place room-temperature egg whites in clean, dry bowl. Attach bowl and wire whip. To avoid splashing, gradually turn to designated speed and whip to desired stage.

AMOUNT SPEED
1 egg white GRADUALLY to 10
2 or more egg whites GRADUALLY to 8

Whipping stages
With your KitchenAid Stand Mixer, egg whites whip quickly. Avoid over- whipping.

WHIPPED CREAM

Pour cold whipping cream into chilled bowl. Attach bowl and wire whip. To avoid splashing, gradually turn to designated speed and whip to desired stage.

AMOUNT SPEED
less than 3/4 cup (200 ml) GRADUALLY to 10
more than 3/4 cup (200 ml) GRADUALLY to 8

Whipping stages
Watch cream closely during whipping. Because your KitchenAid Stand Mixer whips so quickly, there are just a few seconds between whipping stages.

MIXING TIPS

Mixing time

Your KitchenAid Stand Mixer will mix faster and more thoroughly than most other electric mixers. Therefore, the mixing time in most recipes must be adjusted to avoid over-beating.

To help determine the ideal mixing time, observe the batter or dough and mix only until it has the desired appearance described in your recipe, such as “smooth and creamy.” To select the best mixing speeds, use the “Speed control guide” section.

Adding ingredients

The standard procedure to follow when mixing most batters, especially cake and cookie batters, is to add:

1/3 dry ingredients
1/2 liquid ingredients
1/3 dry ingredients
1/2 liquid ingredients
1/3 dry ingredients

Use Speed 1 until ingredients have been blended. Then gradually increase to desired speed.

Always add ingredients as close to side of bowl as possible, not directly into moving beater. The pouring shield can be used to simplify adding ingredients.

NOTE: If ingredients in very bottom of bowl are not thoroughly mixed, the beater is not far enough into the bowl. See the “Assembling the Stand Mixer” section.

Cake mixes

When preparing packaged cake mixes, use Speed 4 for medium speed and Speed 6 for high speed. For best results, mix for the time stated on the package directions.

Adding nuts, raisins, or candied fruits

Solid materials should be folded in the last few seconds of mixing on Speed 1. The batter should be thick enough to keep the fruit or nuts from sinking to the bottom of the pan during baking. Sticky fruits should be dusted with flour for better distribution in the batter.

Liquid mixtures

Mixtures containing large amounts of liquid ingredients should be mixed at lower speeds to avoid splashing. Increase speed only after mixture has thickened.

Kneading yeast doughs

ALWAYS use the dough hook to mix and knead yeast doughs. Use Speed 2 to mix or knead yeast doughs. Use of any other speed creates high potential for unit failure.

Do not use recipes calling for more than 7 cups (900 g) all-purpose flour or 6 cups (800 g) whole-wheat flour when making dough in a 4.28-L bowl.

Do not use recipes calling for more than 8 cups (1 kg) all-purpose flour or 6 cups (800 g) whole-wheat flour when making dough in a 4.8-L bowl.

CARE AND CLEANING

CLEANING THE STAND MIXER

IMPORTANT: Do not wash the wire whip in the dishwasher. Do not immerse the Stand Mixer body in water or other liquids. These parts should be hand- washed.

1 Turn Stand Mixer off and unplug before cleaning. Wipe the Stand Mixer body with a soft, damp cloth. Do not use household/commercial cleaners. Wipe off the beater shaft frequently to remove any accumulation of residue. Do not immerse in water.

2 Bowl, pouring shield*, flat beater, and white dough hook may be washed in a dishwasher. Or, clean them thoroughly in hot sudsy water and rinse completely before drying. Do not store beaters on shaft.

3 IMPORTANT: The wire whip is not dishwasher-safe. Clean it thoroughly in hot, sudsy water and rinse completely before drying. Do not store wire whip on shaft.

*Accessory sold separately

TROUBLESHOOTING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

If your Stand Mixer should malfunction, please check the following:

1. The Stand Mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal.

2. The Stand Mixer may emit a pungent odor, especially when new. This is common with electric motors.

3. If the flat beater hits the bowl, stop the Stand Mixer. See the “Assembling the Stand Mixer” section and adjust the beater to bowl clearance.

4. The speed control lever does not move smoothly or easily. To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

5. If your Stand Mixer should fail to operate, please check the following:

Is the Stand Mixer plugged in?
Is the fuse in the circuit to the Stand Mixer in working order? If you have a circuit breaker box, be sure the circuit is closed.
Turn off the Stand Mixer for 10-15 seconds, then turn it back on. If the Stand Mixer still does not start, allow it to cool for 30 minutes before turning it back on.

If the problem cannot be corrected: See the “Warranty and service” section. Do not return the Stand Mixer to the retailer; retailers do not provide service.

WARRANTY AND SERVICE

KITCHENAID STAND MIXER WARRANTY FOR THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA, PUERTO RICO, AND CANADA

This warranty extends to the purchaser and any succeeding owner for Stand Mixers operated in the 50 United States, the District of Columbia, Puerto Rico, and Canada.

Length of Warranty:	One Year Full Warranty from date of purchase.

KitchenAid Will Pay for Your Choice of:

| Hassle-Free Replacement of your Stand Mixer. See the next page for details on how to arrange for service, or call the Customer eXperience Center toll- free at 1-800-541-6390.
OR
The replacement parts and repair labor costs to correct defects in materials and workmanship. Service must be provided by an Authorized KitchenAid Service Center.
KitchenAid Will Not Pay for:| A. Repairs when your Stand Mixer is used in other than normal single family home use.
B. Damage resulting from accident, alteration, misuse or abuse.
C. Any shipping or handling costs to deliver your Stand Mixer to an Authorized Service Center.
D. Replacement parts or repair labor costs for Stand Mixer attachments operated outside the 50 United States, District of Columbia, Puerto Rico, and Canada.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.

HASSLE-FREE REPLACEMENT WARRANTY—50 UNITED STATES, DISTRICT OF

COLUMBIA, AND PUERTO RICO

We’re so confident the quality of our products meets the exacting standards of KitchenAid that, if your Stand Mixer should fail within the first year of ownership, KitchenAid will arrange to deliver an identical or comparable replacement to your door free of charge and arrange to have your original Stand Mixer returned to us. Your replacement unit will also be covered by our one year limited warranty.

If your Stand Mixer should fail within the first year of ownership, simply call our toll-free Customer eXperience Center at 1-800-541-6390 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address (no P.O. Box numbers, please).

When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.

HASSLE-FREE REPLACEMENT WARRANTY—CANADA

We’re so confident the quality of our products meets the exacting standards of the KitchenAid brand that, if your Stand Mixer should fail within the first year of ownership, we will replace your Stand Mixer with an identical or comparable replacement. Your replacement unit will also be covered by our one year limited warranty.

If your Stand Mixer should fail within the first year of ownership, simply call our toll-free Customer eXperience Center at 1-800-807-6777 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address.

When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.