BRAYER BR1202 Blenders Submersible Kitchen Chopper Food Mixer Instruction Manual

: June 3, 2024
: BRAYER

Table of Contents

BR1202 Blenders Submersible Kitchen Chopper Food Mixer
DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
USING THE BLENDER
CLEANING AND CARE
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction manual
Blender BR1202

BR1202 Blenders Submersible Kitchen Chopper Food Mixer

The blender is intended for making vegetable or fruit blends. The vacuum lid supplied with the unit is intended for longer storage of prepared mixture. Using the lid with the valve you can take the mixture prepared in the bottle with you and use it any time.

DESCRIPTION

1. Vacuum pump on button « »
2. Vacuum pump
3. Vacuum lid
4. Bottle
5. Knife block
6. Motor unit
7. Lid with valve
8. USB cord connector socket| 9. Battery charging indicator
10. USB cord
11. Back-pressure valve
12. Vacuum lid body
13. Sealing gasket
14. Vacuum valve
15. Vacuum valve body
16. Protective lid
---|---

BRAYER BR1202 Blenders Submersible Kitchen Chopper Food Mixer - FIGURE
1

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the unit, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.

ATTENTION! Continuous operation time should not exceed 1 minute. Make at least a 5 minute break between the operation cycles.

Do not use the unit outdoors.
It is recommended not to use the unit during lightning storms.
Place and use the unit on a flat dry and steady surface.
Protect the unit from impacts, falling, vibrations and other mechanical stress.
Never leave the unit connected to the mains unattended.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
Do not let the power cord hang over the edge of the table or touch hot surfaces and sharp edges of furniture.
Unplug the unit after usage or before cleaning. When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
Do not touch the unit body, the power cord and the power plug with wet hands.
Before using the unit for the first time, wash all the removable parts that will contact food thoroughly.
Use only the parts supplied.
Before switching the unit on, make sure that the knife block and the bottle are installed properly and fixed.
Put the products into the bottle before switching the unit on. Do not switch the unit on if the bottle is empty.
Cool down hot products before putting them into the bottle.
Watch the amount of products put in the bottle and the level of poured liquids.
The cutting edges of the knife block are sharp and dangerous, handle the knife block carefully.
If the knife block stops rotating during the unit operation, unplug the unit, remove the bottle, remove the knife block and remove the product which is hindering the knife block rotation. Always add enough water or juice into the bottle.
Remove the bottle from the motor unit only after disconnecting the motor unit from the mains.
Do not put the bottle into a microwave oven.
Do not wash the removable parts of the blender in a dishwashing machine.
- Before using the vacuum lid make sure that it is assembled correctly and installed properly on the blender bottle.
- Watch the level of liquid in the blender bottle. While using the vacuum lid the amount of liquid should not exceed 500 ml.
- Do not switch the vacuum pump on if the blender bottle is turned upside down, if it is vibrating during the blender operation or if the bottle is tilted.
- Do not open the back-pressure valve if the bottle is turned upside down.
- For children safety reasons do not leave polyethylene bags used as a packaging unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

Unpack the unit and remove all the packaging materials.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
Wash the lid (7), protective lid (16) and the bottle (4) with warm water and neutral detergent, rinse and dry.
Wash the knife block (4) (only from the knives side) with warm water and neutral detergent, rinse and dry.
The cutting edges of the knife block (5) are sharp and can be dangerous, handle the knife block (5) carefully.
Clean the motor unit (6) body with a soft, slightly damp cloth, and then wipe it dry.
Do not immerse the unit, the power cord and the power plug into water or any other liquids.

Charging the vacuum pump (2) battery
The vacuum pump is intended for pumping the air out of the blender bottle (4).

To charge the battery insert the mini-USB jack into the connector socket (8).
Insert the USB jack into the power adapter socket (not supplied).
The power adapter should correspond to the following specifications:
Power supply: 110-240 V ~ 50/60 Hz
Output voltage: 5V 1000 mA
Connect the power adapter to the mains socket, the indicator (9) will light up red. When the battery is fully charged, the indicator (9) will light up green.
Disconnect the power adapter from the mains, disconnect the USB jack from the socket (8).

Preparing the vacuum lid (3)
The vacuum lid (3) is intended for longer storage of prepared mixture in the blender bottle (4).

Before using the vacuum lid (3) make sure that it is clean and clean it, if necessary (see the table).

How to prepare and check the vacuum lid and the vacuum valve.

| Step 1:
Remove the assembled vacuum lid (3) from the bottle (4) turning it counterclockwise.
---|---
| Step 2:
Turn the housing (15) of the Vacuum valve (14) against the clockwise down.
| Step 3:
Make sure there are no liquid droplets or foreign matter inside or on the vacuum valve (14). Rinse and dry the parts.
| Step 4:
Put the vacuum valve (14) into the housing (15) and turn the housing (15) after thread in clockwise to
| Step 5:
Set the the assembled vacuum lid (3) onto the bottle (4) and screw it clockwise to the thread.

USING THE BLENDER

The blender is used for making vegetable or fruit blends.
ATTENTION! Continuous operation time of the blender should not exceed 1 minute, after that make at least 5 minutes break.
Note: when using the unit for the first time, a foreign smell from the electric motor can appear – this is normal and it is not covered by warranty.

Place the blender on a flat dry and steady surface.

Notes:

the blender is not intended for crushing hard and frozen food, chopping meat and meat products.
the amount of the processed products should not exceed 2/3 of the bottle (2) capacity.
before starting to chop/mix, we recommend to peel fruit or vegetables, remove stones, and cut fruit or vegetables into 1х1×1 cm cubes.

Note: always add necessary amount of water or juice into the bottle (2).
ATTENTION!
Best proportion while processing the food: 2 parts of fruit to 3 parts of water or juice.
When making mixtures the total amount should not exceed 600 ml.
If you are going to use the vacuum lid (3) intended for longer storage of the prepared mixture, the maximal amount should not exceed 500 ml.

Install the knife block (5) in the bottle (4) and turn the knife block (5) counterclockwise (left-hand thread).
Do not make excessive efforts while turning the knife block (5).
Once again make sure that the knife block (5) is installed correctly.
Put the necessary ingredients in the bottle (4) and add the required amount of liquid.
Install the assembled vacuum lid (3) on the upper part of the bottle (4) and thread it rotating clockwise. Do not apply excessive efforts when screwing the lid (3).
Install the protective lid (16) on the vacuum lid (3) and turn it clockwise until bumping.
Match the mark « » on the bottle (4) with the mark « » on the motor unit (6), insert the bottle (4) into the motor unit (6) body and turn the bottle (4) clockwise until bumping. Make sure that the bottle (4) is fixed properly.
Before switching the blender on you should decide how you will use the prepared mixture – use it immediately or store it in the fridge.

1. Using the processed products:

insert the power plug into the mains socket, the blender will switch on;
do not exceed the recommended operation time. After chopping the products unplug the unit;
turn the bottle (4) counterclockwise and remove it from the motor unit (6);
turn over the bottle (4) and remove the knife block (5) turning it clockwise;
take the processed products out of the bottle (4);
if you are going to take the bottle (4) with you, flip the bottle (4) and remove the knife block (5) turning it clockwise, install the lid (7) on the bottle (4) turning it counterclockwise. When you use the lid (7), open the valve, add the necessary amount of the product and close the valve.

Note: You can leave the vacuum pump (2) on the lid (3) and after consuming the product turn over the bottle (4) and press the button (1) to create vacuum in the bottle (4). It provides the best conditions for the product storing.

After removing the knife block (5) wash it (from the knives side only) and dry.

ATTENTION: The knife block (5) cutting edges are very sharp and dangerous. Handle the knife block (5) carefully.
2. Storing the processed products in the bottle (4)
ATTENTION!
If you are going to use the vacuum lid (3) intended for longer storage of the prepared mixture, the maximal amount should not exceed 500 ml.
Before using the vacuum lid (3) make sure that it is assembled correctly and installed properly on the blender bottle (4).
Do not switch the vacuum pump (2) on if the blender bottle (4) is turned upside down, if the bottle (4) is vibrating during the blender operation or if the bottle (4) is tilted.
If you accidentally tilted the bottle at more than 90 degrees, the vacuum pump will switch off automatically.
Do not open the back-pressure valve (11) if the bottle (4) is turned upside down.

press the button (1) « », the vacuum pump will switch on for approximately 1 minute (the operation time of the vacuum pump depends on the amount of the ingredients in the bottle (4));

Note: fix operation time limits for the vacuum pump. After 3 minutes of operation make at least 30 minutes break.

to check whether there is vacuum in the bottle (4) remove the vacuum pump (2) and pull the back- pressure valve (11). If you hear a sound of air entering the bottle (4), it means that the vacuum lid (3) is in good working order. Install the vacuum pump (2) on the lid (3) and switch it on again pressing the button (1) « ».
remove the vacuum pump (2) by turning it counterclockwise;
install the protective lid (16) instead of the vacuum pump (2) and turn it clockwise;
insert the power plug into the mains socket, the blender will switch on;
do not exceed the recommended operation time. After chopping the products unplug the unit;
turn the bottle (4) counterclockwise and remove it from the motor unit (6);
remove the vacuum pump (2) turning it counterclockwise;
put the bottle (4) in the fridge for storage;

Note: vacuum in the bottle (4) extends the storage life of the processed products, but not for an indefinite period of time. Before consuming check the product carefully and if you find any signs of spoilage, do not consume it.

before removing the vacuum lid (3) you have to admit air to the bottle (4), remove the protective lid (16) by turning it counterclockwise, pull the back-pressure valve (11) and the air will be admitted to the bottle (4);
remove the vacuum lid (3) turning it counterclockwise and remove the products from the bottle (4)

CLEANING AND CARE

Unplug the blender after you finish using it.
Wash the lid (7), protective lid (16) and the bottle (2) with warm water and neutral detergent, rinse and dry.
You can wash the bottle (4) and the vacuum lid (3) in a dishwashing machine.
Wash the knife block (4) (only from the knives side) with warm water and neutral detergent, rinse and dry.
Prepare the vacuum lid (3) for the use according to the recommendations given in the table.
Clean the motor unit body (6) and the vacuum pump (2) with a soft, slightly damp cloth, and then wipe them dry.
Do not use abrasives or solvents to clean the motor unit body (5) and the removable parts.
Do not immerse the motor unit (5) body, the power cord and the power plug into water or any other liquids.

STORAGE

Clean the unit before taking it away for storage.
Keep the unit in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Tabletop blender – 1 pc.
Knife block – 1 pc.
Bottle – 1 pc.
Lid – 1 pc.
Protective lid – 1 pc.
Vacuum lid – 1 pc.
Vacuum pump – 1 pc.
USB cord – 1 pc.
Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V ~ 50/60 Hz
Rated input power: 300 W
Bottle capacity: – 0,6 l
Maximal operation time: – 1 minute

RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, but take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to¬ change the appearance, design and specifications¬ not affecting general operation principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions promptly apply to the authorized service center.

Hergestellt für «Ruste GmbH»,
Berggasse 18/18, 1090 Wien,
Osterreich
Produced for «Ruste GmbH»,
Berggasse 18/18, 1090 Vienna, Austria
Изготовлено по заказу Русте Гмбх,
Бергассе 18/18, 1090 Вена, Австрия
Уполномоченное изготовителем
лицо: ООО «Грантэл»
143912, МО, г. Балашиха,
ш. Энтузиастов, вл. 1А
т.: +7 (495) 297-50-20,
e-mail:info@brayer.su
Made in China/Произведено в Китае
brayer.su