BLAUPUNKT AVMC 1.0 ALL-VIEW-MONITORING CAMERA Installation Guide
- June 7, 2024
- Blaupunkt
Table of Contents
ALL-VIEW-MONITORING CAMERA
AVMC 1.0
Enjoy it.
Operating and Installation Instructions
CAUTIONS
Safety Notes
This vehicle security system has been manufactured according to established
safety guidelines. However, dangers may still occur if the safety notes in
this manual are not observed. This manual is intended to familiarize the user
with the reverse camera important functions. Read this carefully, prior to
using the product. Keep this manual in an easily accessible location. In
addition, do observe the instructions of the devices used in conjunction with
this all-view monitoring camera.
Attentions
- Assign a mounting location that will not obstruct the driver in any circumstances. Or cause injuries to drives and passengers in case of emergency brakes or accidents.
- Ensure all wires are connected properly, and that the unit is functioning well before fitting the unit into the mount.
- Any unauthorized installation, disassembly, or modification may cause malfunction to the unit and void the warranty of the unit.
- Always use only the parts that are included with the units only.
- Do not damage vehicle components when drilling holes for the mount.
- The vehicle may differ from the description provided here. Consult an authorized Blaupunkt dealer or vehicles manufacturer if the information provided here does not fit your specific installation requirement.
- This unit is applicable for front, rear, and side camera use. Consult an authorized Blaupunkt dealer during installation.
- The unit does not record video. Avoid automatic car wash or high-pressure water to prevent water and pressure from damaging the camera or causing it to fall off.
- Do not install this unit near the heater outlet.
This manual may be updated from time to time without any notice
Disclaimer
In no event shall Blaupunkt be liable for any direct, indirect, punitive,
incidental, special consequential damages to property or life and whatsoever
arising out of or connected with the use or misuse of our products. USA &
CANADA: This product is not intended for sale in the United States and Canada.
If purchased in the U.S. or Canada, this product is purchased on an as-is
basis. No
warranty, whether expressed or implied is provided in the U.S. or Canada.
SPECIFICATION
Features
Chip Model| IMX8307(Camera)+NVP2431(Processing)
Camera Specifications| 1/3 inch (6mm)
Effective Pixels| 1297×977=L27MP
Image Resolution| 1000 TVL
Maximum Frame Rate| 720p HD 60fps
Dynamic Range| Support Standard Dynamic Range
Sync System| Internal
Signal Noise Ratio| ≥48dB
Video Signal| 1.0Vp-p at 75ohm
Exposure Control| Automatic
White Balance| Automatic
Illumination Min.| 0.001 Lux/F2.0
Operating Voltage| 3.5V~5.5V
Power Input Range| 3.5V~5.5V
Operating Temperature| -20~75°C
Accessories
WIRING DIAGRAM
INSTALLATION LOCATION
CORRECTION CALIBRATION
NOTE :
- Chessboard Cloth is used for All-View Monitoring Camera Correction Calibration.
- It is excluded from the packaging.
**TROUBLESHOOTING
**
If any of the following problems occur, please resort to Troubleshooting for possible solutions. Consult Blaupunkt authorized dealer if the problem persists.
Problem
|
Solution
---|---
Display monitor/car radio does not show a surround view.| Restart the display
monitor/car radio.
Surround-view does not show even after restarting the display monitor/ car
radio.| Examine if the power supplies are properly connected.
Surround-view does not show even though power supplies of the reverse light or
the rear car plate lights are properly connected.| Examine if the power supply
cables are damaged. Repair/ replace if the cables are damaged.
https://taplink.cc/blaupunkt.apac
Designed and engineered by Blaupunkt Competence Centre
1 321 21 001 20 01