westomatic Primo Compact Water Reservoir Instruction Manual

June 3, 2024
westomatic

westomatic Primo Compact LOGO INSTALL & USE

INSTALL WATER RESERVOIR

The water reservoir allows the achine to be used without mains water connection:

  • External Dimensions Water Reservoir: W230xD420xH455mm
  • External Dimensions Total: W530xD515xH600mm
  • Capacity Water Reservoir: 8.2litres/5.2litres with the Filter

westomatic Primo Compact Water Reservoir - FIGURE 1

Parts Included:
Check the contents:

  • Water Reservoir
  • Water Container
  • Water Hose
  • Hose Connector x2
  • Internal Power cable (red & purple wire)
  • Power cable (black)
  • User manual
  • Brita Filter & cartridge (optional use)
  • OPTIONAL: Ingredient Box PN: 1057339

westomatic Primo Compact Water Reservoir - FIGURE 2

NB: The machine will have been set up to your specifications and tested at Westomatic HQ prior to install. All parts have been assembled on the machine. The QR code inside the machine gives access to the We:Support pages with technical information.

  1. Place the Water reservoir on a level surface Min Clearances: Rear: 50mm
  2. Ensure the protective plastic is removed from the top
  3. Switch off and UNPLUG the Primo Compact from the mains power
  4. Remove the screws from the back cover
  5. Remove the cover plate for the power cable feed through
  6. Locate the power pins remove the red and purple wire connectors
  7. Connect the internal power cord to the plugs Red-Red/PurplePurple
  8. Place plugs back on power pins
  9. Guide the internal power cable to the opening in back cover and push through
  10. Replace the back cover and fasten the two screws
  11. Remove the red cover from the water entry on the Primo
  12. Attach water connector and tighten
  13. Insert the water hose in the connector
  14. Insert water hose into the water connector and then attach to the water reservoir
  15. Connect the Primo and the water reservoir with the external power cable
  16. Connect the Primo to the power outlet and Switch on
  17. Water Reservoir is now installed

USING THE RESERVOIR:

These instructions show how to commission the reservoir to use :

  • Ensure the Water Reservoir is clean before every refill
  • The reservoir is dishwasher safe to max 50°C
  • NB. The Brita filter lid should be cleaned by hand (if using)

westomatic Primo Compact Water Reservoir - FIGURE 20

  1. Fit filter into the Brita Filter lid (If using)
  2. Fill container with water: 8.2litres Total (5.2liters with filter)
  3. Close the lid
  4. Place the water tank into the unit and push to the back
  5. There is space under the tank for spare water filters
  6. On the main screen select the Main Menu
  7. Select OPERATOR MENU
  8. Enter Operator Pin-Code Default = 11111
  9. Choose SERVICE MENU (1.07)
  10. Enter Pin-Code again to enter Service Menu
  11. Select SETTINGS (2.04) Select EXTERNAL WATER TANK (2.04.19)
  12. Switch to ACTIVE, Select WATER RESERVOIR, Press SAVE

Water Reservoir is now set up and ready to use.
It is possible to use both the Water Reservoir and the Fresh Milk Fridge at the same time for the full experience.

westomatic Primo Compact Water Reservoir - FIGURE 33westomatic Primo Compact Water Reservoir - FIGURE
34

westomatic Primo Compact LOGO 2 westomatic
LOGOCONTACT
Westomatic Vending
Services Ltd,
Units 7 – 8Forde Court,
Block 4 Forde Road,
Newton Abbot,
TQ12 4 BT
+44(0)1626323100
sales@westomatic.com
www.westomatic.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

westomatic User Manuals

Related Manuals