AcuRite 13131W2 Atomic Alarm Clock Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
- AcuRite 13131W2 Atomic Alarm Clock Instruction Manual
- Unpacking Instructions
- Package Contents
- Features & Benefits
- SETUP
- OPERATION
- Troubleshooting
- Care & Maintenance
- Specifications
- FCC Information
- Customer Support
- Limited One Year Warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AcuRite 13131W2 Atomic Alarm Clock Instruction Manual
Model: 13131W2
Questions? Contact Customer Support at 877-221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove.
Package Contents
- Alarm clock
- Instruction Manual
IMPORTANT
PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com
Features & Benefits
FRONT
- SNOOZE/LIGHT Button
- Atomic Clock Sets itself to the correct time and automatically 3 updates for Daylight 4 Saving Time.
- AM/PM Indicator 5
- Time Zone Indicator
- ALARM Indicator Icon
- Date
- Day of the Week
- Indoor Temperature
- Menu Selection
- Atomic Signal Strength SIDE/BOTTOM
- SET CLOCK Button
- “▲” Button
- “▼” Button
- ALARM ON/OFF Button
- C°/F° Button
- Reset Button
- Battery Compartment Cover (not shown)
SETUP
Clock Setup
Install or Replace Batteries
- Remove the battery compartment cover.
- Insert 3 x AA alkaline batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.
- Replace the battery cover.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS. BATTERY SAFETY:
Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
Atomic Clock (RCC)
AcuRite atomic clocks use a radio-controlled signal (RCC) to synchronize to
the correct time broadcast by the National Institute of Standards and
Technology (NIST) Radio Station WWVB, located near Fort Collins, Colorado.
WWVB broadcasts the current time and date with split-second accuracy.
The atomic clock and calendar will maintain the correct time and date, and automatically update for Daylight Saving Time to provide the most accurate timekeeping standard possible.
Please note: Signal reception is normally better at night and when the weather is clear. The atomic signal generally takes a few hours to synchronize, so it is important to manually set the time and date after powering on the clock.
Set the Time & Date
Press and hold the “SET CLOCK” button, located on the side of the clock, to
enter SET MODE. Once in SET MODE the preference you are currently setting will
blink on the clock.
To adjust the currently selected (flashing) item, press and release the “▲” or “▼“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “SET CLOCK” button to adjust the next preference. The preference set order is as follows:
TIME ZONE (PST MST CST EST AST HAST AKST)
AUTO DST ON/OFF*
CALENDAR YEAR
CALENDAR MONTH
CALENDAR DATE
CLOCK HOUR
CLOCK MINUTE
You will automatically exit SET MODE if no buttons are pressed for 45 seconds. Enter SET MODE at any time by pressing AND HOLDING the “SET CLOCK” button.
*If you live in an area that observes Daylight Saving Time, DST should be set to ON, even if it is not currently Daylight Saving Time.
Alarm Clock Placement
Place alarm clock in a dry area free of dirt and dust. To help ensure an
accurate indoor temperature measurement, be sure to place the clock away from
heat sources or vents.
Important Placement Guidelines
- To ensure accurate temperature measurement, place out of direct sunlight and away from any heat sources or vents.
- To maximize atomic signal reception, place unit away from large metallic items, thick walls, metal surfaces, or other objects that may limit radio communication.
- To prevent wireless interference, place unit at least 3 ft (.9 m) away from electronic devices (TV, computer, microwave, radio, etc.).
OPERATION
Using the Clock
Set the Alarm Time
Press AND HOLD the “ALARM ON/OFF ” button for 5 seconds to enter ALARM SET
MODE.
To adjust the currently selected (flashing) item, press and release the “▲” or “▼“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ALARM ON/OFF“ button to adjust the next preference. The preference set order is as follows:
ALARM CLOCK HOUR
ALARM CLOCK MINUTE
You will automatically exit ALARM SET MODE if no buttons are pressed for 60 seconds. Enter ALARM SET MODE at any time by pressing and holding the “ALARM ON/OFF“ button for 5 seconds.
Alarm Clock ON/OFF function
To Turn Alarm on: Press AND HOLD the “ALARM ON/OFF” button until the ” “ icon
and the words “ALARM ON” appear on the clock
To Turn Alarm off: Press AND HOLD “ALARM ON/OFF” Button until the “ “ icon disappears and the words “ALARM OFF” appear on the clock.
SNOOZE function
When the alarm is sounding, press the “SNOOZE/LIGHT” button to activate the
SNOOZE function for 8 minutes. After the SNOOZE function has been activated 10
times the alarm is automatically deactivated.
Momentary Backlight
Press the “SNOOZE/LIGHT” button to activate the momentary backlight for 5
seconds.
Troubleshooting
If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call 877-221-1252 for assistance.
Care & Maintenance
Clock Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Specifications
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Customer Support
AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this product available and contact us in any of the following ways:
Phone: 877-221-1252
Mail: info@chaney-inst.com
24/7 support at www.AcuRite.com
- Installation Videos
- Register your Product
- Instruction Manuals
- Support User Forum
- Replacement Parts
- Submit Feedback & Ideas
IMPORTANT
PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite.com for the fastest way to register your product. However, product registration does not eliminate the need to retain your original proof of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures to be of good
material and workmanship, and to be free of defects when properly installed
and operated for a period of one year from the date of purchase. Remedy for
breach of this warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is proven to breach
the warranty contained herein within ONE YEAR from date of sale will, upon
examination by Chaney,and at its sole option, be repaired or replaced by
Chaney. Transportation costs and charges for returned goods shall be paid for
by the purchaser. Chaney hereby disclaims all responsibility for such
transportation costs and charges. This warranty will not be breached, and
Chaney will give no credit for products it manufactures which have received
normal wear
and tear, been damaged (including by acts of nature), tampered, abused,
improperly installed, damaged in shipping, or repaired or altered by others
than authorized representatives of Chaney.
The above-described warranty is expressly in lieu of all other warranties, express or implied, and all other warranties are hereby expressly disclaimed, including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose. Chaney expressly disclaims all liability for special, consequential or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Chaney further disclaims all liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of Chaney’s products, the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm or corporation is authorized to assume for Chaney any other liability in connection with the sale of its products. Furthermore, no person, firm or corporation is authorized to modify or waive the terms of this paragraph, and the preceding paragraph, unless done in writing and signed by a duly authorized agent of Chaney. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
It’s more than accurate, it’s
AcuRite offers an extensive assortment of precision instruments, designed to
provide you with information you can depend on to Plan your day with
confidence™.
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China
13131W2 INST 103113
Read More About This Manual & Download PDF:
References
- Home
- AcuRite Weather Monitoring | #1 Weather Station Brand in North America
- Help with WWVB Radio Controlled Clocks | NIST
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>