ACURITE 02020 Lightning Detector Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
Instruction Manual
Lightning Detector
model 02020
Questions? Contact Customer Support at
877-221-1252 or visit
www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel it off to remove it.
Package Contents
- Lightning detector with belt clip
- Instruction Manual
Note: Under no circumstances shall the Lightning Detector, Chaney Instrument Co., or the Primex Family of Companies be held responsible for any damages whatsoever that may result from the use of or inability to use this product, including without limitation any indirect, incidental, special, exemplary or consequential damages, which are expressly disclaimed. This disclaimer of liability applies to any damages or injury caused by any failure of performance, error, omission, inaccuracy, interruption, deletion, defect, delay in operation or transmission software virus, communication failure, theft or destruction or unauthorized access to, alteration of, or use of the product, whether for breach of contract, tortuous behavior (including, without limitation, strict liability), negligence, or under any other cause of action, to the fullest extent permissible by law. This does not affect any statutory rights which may not be disclaimed. The contents of this product, including all lightning and weather data are provided “as is” and without warranty or condition of any kind, express or implied, including, without limitation, any warranty of merchantability or fitness for a particular purpose. Chaney Instrument Co. & the Primex Family of Companies do not warrant that this product or the data that it provides will be free of errors, interruptions, viruses or other harmful components. Chaney Instrument Co. & the Primex Family of Companies do not warrant the accuracy or reliability of any lightning strike alerts, weather data or other information provided by the product. Chaney Instrument Co. & the Primex Family of Companies reserve the right to alter the product or withdraw it from the market at its sole discretion.
Features & Benefits
Lightning Detector
-
Backlight Button
Momentary (5 seconds) backlight for low-light viewing. -
Power Button
Press to power ON, press AND HOLD to power off. -
Strike Counter
Displays running total of lightning strikes that have been detected. -
Status Display
Displays current status of the device and/or instructions. -
Strike Indicator Red LED Light
This indicates a lightning strike has occurred within 25 miles. -
Lightning Strike Indicator LD
This indicates a lightning strike has occurred within 25 miles. -
Low Battery Indicator
-
Estimated Distance to Storm Front
Updates with every lightning strike.
SETUP
Install or Replace Batteries
AcuRite recommends high-quality alkaline batteries for the best product
performance. Heavy duty or rechargeable batteries are not recommended.
- Remove the belt clip.
- Remove the battery cover.
- Insert 2 x AAA batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.
- Replace the battery cover.
- Replace the belt clip.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device
prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity (+/-) diagram in
the battery compartment. Promptly remove dead batteries from the device.
Dispose of used batteries properly. Only batteries of the same or equivalent
type as recommended are to be used. DO NOT incinerate used batteries. DO NOT
dispose of batteries in free, as batteries may explode or leak. DO NOT mix old
and new batteries or types of batteries (alkaline/standard). DO NOT use
rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT
short-circuit the supply terminals.
OPERATION
Using the Lightning Detector
Power On/Off
Press the “button to turn the detector ON. The detector will display “PLEASE
Press ” WAIT” while it automatically calibrates itself. When calibration is
complete “LISTENING..” will display, indicating it is ready for use. Press AND
HOLD the ” ” button for 3 seconds to turn the detector off.
Indoor & Outdoor Modes
Outdoor mode is the default setting. Indoor Mode optimizes the performance of
the detector for indoor use by making it less sensitive to interference.
To select indoor mode, press and “ ” buttons for AND HOLD the “ seconds
until you hear a beep. The display will say “INDOOR”. When powered off, the
detector will return to its default, outdoor mode.
Lightning Detected
The device detects cloud-to-cloud, cloud-to-ground and intra-cloud lightning.
When lightning is detected the detector emits two beeps and the red light
flashes. The display indicates “STRIKES DETECTED!”, and “STRIKE COUNT”
displays a running count of lightning strikes detected. The detector estimates
the distance to the front of the lightning-producing storm. The detector
alerts and flashes the light every 5 seconds until no strikes are detected for
30 minutes. After 30 minutes of inactivity, the detector will return to its
default “LISTENING..” state. The “STRIKE COUNT” resets when the device is
powered off.
False Detection
This detector features advanced technology to distinguish between lightning
strikes and interference, however, in rare cases the detector may “false
detect” lightning activity due to interference. In these situations, verify
there is no lightning in the area and then relocate the detector. If the false
detections persist, identify and relocate the source of interference or
relocate the detector.
Silencing Audio Alerts
Audio alerts (beeps) are enabled by default each time the device is powered
on. Audio alerts can be temporarily silenced for up to 60 minutes. To
temporarily silence audio alerts, press and hold the “LIGHT” button for 5
seconds. The device will display “MUTED”. The visual alerts from the LED light
and display messages will remain active even when audio alerts have been
silenced. When the device detects a lightning strike while audio alerts are
muted, the device will display the message,” STRIKES DETECTED! MUTED” along
with the strike indicator/flashing LED, updated strike count and updated
estimated distance. The device will re-activate audio alerts after 60 minutes
or after audio alerts have been re-enabled. To re-enable audio alerts, press
and hold the “LIGHT” button for 5 seconds. The device will display “SOUND ON”.
Interference
The detector features enhanced interference rejection capabilities to prevent
false lightning detection. When the detector cannot detect lightning due to
interference from nearby equipment, the detector sounds a single audible beep
and displays “UNABLE TO DETECT…PLEASE RELOCATE.”
Use the detector at least 3 feet away from sources of interference, including:
- Electric motors (windshield wiper motor or fan motors in cars, hard drive and optical drive motors on your PC and AV equipment, well pumps, sump pumps)
- CRT monitors (PC monitors, TV’s)
- Fluorescent light fixtures (turned off or on)
- Microwave ovens (while in use)
- PC’s and mobile phones
WARNING: Take shelter IMMEDIATELY when lightning is present, whether or not it has been detected by the Lightning Detector. If you are concerned about lightning strikes, follow all safety precautions to keep yourself and others safe. DO NOT rely on this Lightning Detector as your only source for warnings about potentially deadly lightning strikes or other severe weather conditions.
Alerts & Messages
| Text on Display | Alerts | Message |
|---|
STRIKES
DETECTED!| 2 beeps & light
flashes| Lightning has been detected within 25 miles
INDOOR| None| Confirms the detector is set to operate indoors
LISTENING..| None| The detector is ready for use
LO BATTERY.| icon & 1 beep/minute| Replace batteries
NA| None| Lightning detected beyond 25 miles
PLEASE WAIT| None| The detector is calibrating itself
UNABLE TO
DETECT…PLEASE
RELOCATE| 1 beep| Interference detected, use the detector in a different
location
MUTED| None| Audio alerts were temporarily silenced. Press AND HOW the “LIGHT”
button for 5 seconds to re-enable audio alerts.
Troubleshooting
The display reads “UNABLE
TO DETECT…PLEASE RELOCATE”| •Relocate the detector.
•Make sure the detector is placed at least 3 feet (.9 m) away from electronics
that may cause interference (see page 6).
---|---
Display scan not working| •Check that the batteries are installed correctly.
Batteries may need to be replaced.
Detector beeping| •Review the Alerts & Messages chart above to determine why
the detector is beeping.
If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call 877-221-1252 for assistance.
Care & Maintenance
The detector is weather resistant. It is not intended for direct exposure to rainfall. Clean with a soft damp cloth. Do not use caustic cleaners or abrasives.
Specifications
| OPERATING TEMPERATURE | 32°F to 140°F; 0°C to 60°C |
|---|---|
| LIGHTNING DETECTION RANGE | 1 – 25 miles / 1.6 – 40km |
| LIGHTNING COUNTER | Counts up to 99 strikes (power off to reset counter) |
| AUDIBLE TONE | 85 decibels |
| POWER | 2 x AAA alkaline batteries (not included) |
| BATTERY LIFE EXPECTANCY | 8-10 months – based on an average of 3 lightning |
strikes detected per day
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING : Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, There is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Customer Support
AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways:
877-221-1252
info@chaney-inst.com
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment to quality technology. Chaney
Instrument Co.
warrants that all products it manufactures to be of good material and
workmanship, and to be free of defects when properly installed and operated
for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite.com
for the fastest way to register your product. However, product registration
does not eliminate the need to retain your original proof of purchase in order
to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures to be of good
material and workmanship and to be free of defects when properly installed and
operated for a period of one year from the date of purchase. Remedy for
breach of this warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is proven to breach
the warranty contained herein within ONE YEAR from the date of sale will, upon
examination by Chaney, and at its sole option, be repaired or replaced by
Chaney.
Transportation costs and charges for returned goods shall be paid for by the
purchaser. Chaney hereby disclaims all responsibility for such transportation
costs and charges. This warranty will not be breached, and Chaney will give no
credit for products it manufactures which have received normal wear and tear,
been damaged (including by acts of nature), tampered, abused, improperly
installed, damaged in shipping, or repaired or altered by others than
authorized representatives of Chaney. The above-described warranty is
expressly in lieu of all other warranties, express or implied, and all other
warranties are hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty of fitness for a
particular purpose. Chaney expressly disclaims all liability for special,
consequential or incidental damages, whether arising in tort or by contract
from any breach of this warranty. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. Chaney further disclaims all liability from
personal injury relating to its products to the extent permitted by law. By
acceptance of any of Chaney’s products, the purchaser assumes all liability
for the consequences arising from their use or misuse. No person, firm or
corporation is authorized to assume for Chaney any other liability in
connection with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this paragraph, and
the preceding paragraph, unless done in writing and signed by a duly
authorized agent of Chaney. This warranty gives you specific legal rights, and
you may also have other
rights which vary from state to state.
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
It’s
more than accurate, it’s AcuRite offers an extensive assortment of precision
instruments, designed to provide you with information you can depend on to
Plan your day with confidence™.
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China
02020 INST 060613
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>