DANNER MANUFACTURING 03823 Illuminate Meditation Fountain Instruction Manual

03823 Illuminate Meditation Fountain

“`html

Product Information

Specifications:

• Indoor use only
• Must be submerged in water during operation
• Avoid contact of electrical connections with water
• Includes decorative rocks (model dependent)
• Requires periodic maintenance for optimal performance

Product Usage Instructions

Assembly Instructions:

1. Set the Flow Control on the pump to the fully opened
   position.

2. Insert the plastic fin into the outlet of the pump.

3. Attach the pump and fin to the tubing inside the fountain.

4. Place the fountain on a level surface.

5. Fill the basin with water until it reaches the base of the
   fountain.

6. Add decorative rocks to the top surface of the fountain
   base.

7. Turn on the Tealights switch and place in holders on the
   base.

8. Plug into outlet, ensuring a Drip Loop in the wire.

Care and Operating Instructions:

• Use indoors only.

• Ensure the pump is always submerged in water, do not run
  dry.

• Avoid electrical connections coming into contact with
  water.

• Do not use if product is damaged.

• Check for leaks after setup and periodically.

• Avoid household cleaners on surfaces.

• Always use a Drip Loop when operating the pump.

Maintenance:

• Change water periodically to reduce scaling and mineral
  buildup.

• Check and maintain proper water level.

• Drain water if fountain will be out of service for an extended
  period.

• Rinse pump with fresh water periodically to remove debris.

• Clean basin with tap water and wipe away buildup.

• Use distilled water to prevent mineral buildup.

FAQ

Q: What should I do if there is no water flow shortly after

powering up?

A: Unplug the fountain and check if the flow control on the pump
is fully open. If needed, remove any trapped air by taking out the
pump, then placing it back in the filled basin.

Q: How can I prevent splashing while the fountain is

running?

A: Try rearranging the rocks or reduce the flow rate by
adjusting the stem on the front cover of the pump.

“`

Assembly Instrucons
The following instrucons will assist you in assembling your parcular fountain. Depending on which fountain you purchased, there will be slight variaons in the assembly process.

Felicity with Tealights ­ Item # 03823

Mantra with Tealights ­ Item # 03851
Fountain Base Tubing

Fig. A

Fig. B

Fig. C Pump installed onto Tubing

Step 1. Set the “Flow Control” on the pump to the fully opened posion. Do this by sliding the stem on the front of the pump cover all
+ the way over to the ” ” sign. (see Fig. A)

Step 2. Insert the included plasc fing into the outlet of the pump. Some models may already have the fing pre-installed. (see Fig. A)

Step 3. Turn the fountain upside down and atach the pump & fing to the so tubing extending down from the inside of the fountain. (see Fig. B and Fig. C)

Step 4. Place the fountain with the atached pump onto the basin. Be sure to check that the basin is sing on a level surface.

Step 5. Slowly fill the basin with water unl it reaches the base of the fountain.

Step 6. Add the included decorave rocks (dependent on model) to the top surface of the fountain base.

Step 7. Slide the switch located on the rear side of Tealights to the “ON” posion and place in each of the (2) holders on the base of the fountain.

Step 8. Plug into outlet. Be sure to leave a “Drip Loop” in the wire (see Fig.

Setup hints:

1. If water does not flow shortly aer power up, unplug and refer to STEP 1 to confirm that the flow control is in the fully open posion. OR Air may be trapped within the pump. Remedy this by removing the pump from the water & placing back into the filled basin.
2. If splashing occurs when the fountain is running, try re-arranging the rocks or reduce the flow rate on the pump by sliding the stem on the front cover towards the other side.

Care and Operang Instrucons

WARNINGS:

·

This product is for INDOOR use only.

·

Pump must ALWAYS be submerged in water. DO NOT RUN DRY.

·

Keep ALL electrical connecons out of the water.

·

Never plug into an electrical outlet if any part of the product appears to be damaged.

·

Check for leaks aer inial setup and occasionally aerwards.

·

DO NOT use any household cleaners on any of the surfaces.

·

ALWAYS use a “Drip Loop” when operang the pump (see Fig.1).

SAVE THESE INSTRUCTIONS

MAINTENANCE:

·

Change water periodically to reduce scaling & mineral buildup.

·

Check water level and add as necessary to maintain proper level.

·

Drain all water from the basin if the fountain will be out of service for an extended period of me.

·

Remove pump from fountain periodically and rinse with fresh water to remove any debris or buildup.

·

Rinse basin periodically with tap water and wipe away any buildup.

·

Use of dislled water will prevent mineral buildup.

Limited Warranty
E. G. Danner will repair or replace any unit found to be mechanically defecve within 90 days of purchase. For warranty issues please contact Danner Customer Service for informaon before returning the product. A dated proof of purchase must be presented to validate any warranty claim. Damage or injuries resulng from negligence, abuse or misuse of this product are excluded from this warranty. This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ZG0380TL Rev. B 02/24
DANNER MFG. INC. · Islandia, NY 11749-1489 · Phone 631-234-5261 · Visit our website at www.Dannermfg.com

References

• Danner Manufacturing Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>