CERTA CTTPMSTLAPA 4 Wheel Smart Tyre Pressure Monitoring System User Guide
- June 7, 2024
- CERTA
Table of Contents
USER GUIDE
4 WHEEL SMART TYRE PRESSURE MONITORING SYSTEM
CTTPMSTLAPA
SAFETY & WARNINGS
- Read all instructions before installing the sensors and retain them for future reference.
- Use caution when working around excessive air pressure in car tires.
- Deflate the tire before attempting the installation of internal tire sensors.
- Keep the lithium button batteries away from children
- Dispose of the lithium batteries correctly in accordance with your local authorities.
COMPONENTS
APP INSTALLATION
Download and install the “Smart TPMS” app from App Store (Apple) or Google Play Store (Android).
App System Requirements
- Android 4.3 and above
- iOS 7.0 and above
- Bluetooth 4.0 and above
Pairing Sensors
Note:
Pair all sensors with a smartphone before installation onto the tire
Step 1.
- Open the “Smart TPMS” app on your mobile device. You will be prompted to turn on the Bluetooth if it is not already active.
- On the app main screen, select one of the four “Bind Device” options.
Step 2a. Manual Pairing:
- Select “Manual Matching”.
- Select one of the tire positions and enter the sensor ID number for the corresponding sensor (refer to the “Sensor ID codes” section of this user guide).
- Repeat for the remaining sensors.
| 
---|---
Step 2b. Automatic Pairing:
- Select “Automatch”.
- Once the app begins scanning, slowly insert the battery on the sensor halfway to put the sensor into pairing mode.
- Once the app has successfully paired with the sensor, the battery can be fully inserted into the sensor.
- Repeat for the remaining sensors.
| 
---|---
Step 3.
- Once all sensors have been paired, return to the main screen where tyre pressure data is displayed.
- A voice message will play, “Tire pressure and temperature is normal, enjoy your driving”
Application Settings
To access the app settings, press the button in the top left corner of the main screen.
Auto Start:| The app will automatically start when the phone is powered
on
---|---
Voice Alarm:| The mobile phone will play a voice alarm if the safety
values of the sensor are exceeded.
Pressure Unit:| Bar, Psi, a
Pressure – Range:| Set the minimum and maximum tire pressures
which will trigger the Voice Alarm. Refer to your car user manual or tire
specifications to identifying your preferred settings. Default settings are set to 2.0 and 3.0 Bar respectively.
Temp – Unit:| Cycle between Celsius °C and Fahrenheit °F.
Temp – Range:| Set the maximum temperature that you do not want
the tire to exceed. Refer to your car user manual or tire specifications to
identify your preferred settings. The default value is 65°C.
Restore Defaults Settings:| Revert to original settings
Sensor ID codes
Use these ID codes to manually pair the sensors with the app.
INSTALLATION
Note:
Ensure all sensors are paired with the app before installing the sensors onto
your wheels.
- Screw the anti-tamper nut onto the tire valve.
- Screw the sensor onto the tire valve
- Screw the anti-tamper ring counterclockwise until It makes contact with the sensor.
- Tighten the anti-tamper ring using the supplied spanner.
- Repeat steps 1-4 for the remaining sensors.
- Keep the wrench safe and accessible as it will be needed to remove the sensors.
Replacing the Battery
- Remove the sensor using the supplied spanner.
- Insert the sensor into the battery replacement tool.
- Screw the anti-tamper ring counter-clockwise until It makes contact with the sensor.
- Open the battery compartment by rotating the battery replacement tool clockwise.
- Remove and discard the old battery.
- Replace the battery with a CR1632 battery.
- Refer to the pairing steps to reconnect the sensor to the app.
TROUBLESHOOTING
Data is not displayed after pairing sensors.
TPMS sensor data may only be available after the vehicle exceeds 20km/h while
driving or after the vehicle has been driven for 11 minutes.
If tire pressure is at or below 0.3 bar the sensor will enter a power-saving
mode.
Sensors have been paired and the vehicle is running but no values are
displayed.
Restart the application and confirm that Bluetooth is turned on. Data will be
received in 2 minutes under normal circumstances.
App interface indicates abnormal tire conditions, but no voice prompt is
heard.
Confirm that the voice message function is activated in settings. Ensure
the phone is not in silent mode or volume is set to a minimum.
An excessive tire pressure difference was found in the first installation.
After initial installation, the air pressure of the tire may have not yet fully passed through to the sensor. The sensor will read the correct pressure value as the air is distributed after 5-10 minutes of driving.
Need more information?
We hope that this user guide has given you the assistance needed for a simple
setup.
For the most up-to-date guide for your product, as well as any additional
assistance you may require,
head online to help.kogan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>