TESLA WH1257500 Wireless Charging Platform User Manual
- June 9, 2024
- Tesla
Table of Contents
TESLA WH1257500 Wireless Charging Platform
What’s in the box
- Charger
- Magnetic Stand
- 45W USB-C Power Supply.
Configurations
- Flat
- Tilted (with Magnetic Stand)
Cable Routing With Stand
Route cable through the stand and out the bottom.
Power On
- Plug USB-C cable into 45W USB-C power supply
- Plug power supply into power outlet.
Charge Devices
Drop devices flat on Alcantara surface.
Device Not Charging
Devices placed over the aluminum frame will not charge.
LED Status Indicator
LED on bottom side of front edge indicates status.
FreePower Wireless Charging
FreePower wireless charging is the technology inside that powers the Tesla
Wireless Charging Platform. To learn more about FreePower, visit
www.freepower.io
SPECIFICATION
- USB-C PD: Any 15V 3A USB-C PD power supply
- Charge Performance: Wireless charging performance may vary. For best results, keep charger out of direct sunlight and warm environments, use a thin phone case or no phone case.
- Safety: This product is intended for home and office use only. Prevent cable from being pinched or damaged. Unplug the product if not used for an extended period of time. Use in dry locations.
- Foreign Objects: If a metal object is detected between the wireless charger and a device charging, transmitting power will stop and the LED status indicator will show a slow pulsating blink. Remove device and ensure there are no metal objects attached to the device or on the surface on the charger before resuming normal operation.
- Compatibiliy: Qi Certified devices
- Tesla Logo: Product of Tesla, Inc1 Tesla Road, Austin, TX 78725
- FreePower Logo: Product of Aira, Inc 2048 N 44th St, Phoenix, AZ 85008
- Regulatory Info: FCC ID: 2AWGG-WH1257500 and IC: 29612-WH1257500
- Part Number: 1799799
- Support Contact: OnlineOrders@Tesla.com
- IP Rating: IPX2
FCC Notice
This device complies with Part 15, Subpart C, of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Tesla could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
ISED Compliance Statement:
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
Radio Frequency Exposure:
This device meets the Innovation, Science and Economic Development Canada
requirements for exposure to radio waves and is designed and manufactured not
to exceed the emission limits for exposure to radiofrequency (RF) energy. To
comply with Canada RF exposure compliance requirements, this device must not
be co-located or operating in conjunction with any other antenna or
transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>