poly TC10 Intuitive Touch Interface Instructions

June 9, 2024
Poly

poly TC10 Intuitive Touch Interface

SAFETY AND REGULATORY NOTICES

Poly TC10
This document covers Poly TC10 (Models P030 and P030NR).

Service Agreements
Please contact your Poly Authorized Reseller for information about service agreements applicable to your product.

Safety, Compliance, and Disposal Information

  • This equipment is intended for indoor use only.
  • This equipment is not intended to be directly connected to outdoor cables.
  • Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static-free cloth.
  • Do not immerse the system in any liquids or place any liquids on it.
  • Do not disassemble this system. To reduce the risk of shock and to maintain the warranty on the system, a qualified technician must perform service or repair work.
  • There are no user serviceable parts inside this product.
  • This equipment is not intended to be operated by children.
  • Users must not service any parts in compartments that require a tool to access.
  • This equipment should be used only on even surfaces.
  • Keep ventilation openings free from any obstructions.
  • The ambient operating temperature rating of this equipment is 0-40°C and should not be exceeded.
  • In order to remove all power from this unit, disconnect all power cables, including any USB or Power over Ethernet (PoE) cables.
  • If the product is powered using PoE, you must use an appropriately rated and approved networking device compliant with IEEE 802.3af, or the power injector identified for use with this product.

Operating Ambient Temperature

  • Operating temperature: +32 to 104°F (0 to +40°C)
  • Relative humidity: 15% to 80%, non-condensing
  • Storage temperature: -4 to 140°F (-20 to +60°C)

Installation Instructions

  • Installation must be performed in accordance with all relevant national wiring rules.

FCC STATEMENT

USA

This device is compliant with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference.
  • This device must accept any interferences received, including interference that may causeundesired operation.

In accordance with part 15 of the FCC rules, the user is cautioned that any changes or modifications not expressly approved by Poly could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Responsible Party issuing FCC Supplier’s Declaration of Conformity

Polycom, Inc. 6001 America Center Drive San Jose, CA 95002 USA TypeApproval@poly.com.

Radiation Exposure Statement
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 centimeters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device with its antenna complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement

Canada

This device complies with RSS247 of the Industry Canada rules and also with ISED’s license-exempt RSS regulations. Operation is subject to the two following conditions:

  1. This device does not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesiredoperation.

Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20 cm between the radiator and your body.

FCC and Industry Canada Example Label

  • See an example of the Poly TC10 regulatory label below.
  • FCC ID: M72-P030
  • IC: 1849C-P030poly-TC10-Intuitive-Touch-Interface-FIG-1

DECLARATION

EEA

CE Mark

P030 is marked with the CE mark. This mark indicates compliance with EU Radio Equipment Directive (RED) 2014/53/EU, RoHS Directive 2011/65/EU, and Commission Regulation 278/2009. P030NR is marked with the CE mark. This indicates compliance with the EU EMC Directive (EMCD) 2014/30/EU, Low Voltage Directive (LVD) 2014/35/EU, RoHS Directive 2011/65/EU and Commission Regulation 278/2009. A full copy of the Declaration of Conformity for each model can be obtained at www.poly.com/conformity.

Poly Studio TC10 Radio Operating Frequency
The frequency ranges in the following table apply to Poly Studio TC10 (P030 )poly-TC10-Intuitive-Touch-Interface-FIG-2 Restriction of Hazardous Substances Directive (RoHS)
All Poly products comply with the requirements of the EU RoHS Directive. Statements of compliance can be obtained by contacting typeapproval@poly.com.

Environmental
For the latest environmental information including Networked Standby Efficiency, battery replacement, handling, and disposal, take back, RoHS, and Reach, please visit https://www.poly.com/us/en/company/corporate- responsibility/environment.

End of Life Products

Poly encourages you to recycle your end-of-life Poly products in an environmentally considerate way. We recognize our Extended Producer Responsibility (EPR), in accordance with the requirements of the European Waste Electronic and Electrical Equipment (WEEE) Directive 2012/19/EU. All Poly products are marked with the crossed wheelie bin symbol shown below. Products that carry this symbol should be not be disposed of in the household or general waste stream. Further recycling information and detail of the options open to you, including our voluntary free global recycling service to ISO 14001 standard can be found at: https://www.poly.com/WEEE. The Poly Global Producer Responsibility Statement can be found in the Environment section of the Poly.com website.

Poly Take Back
In addition to any mandated take back requirement, Poly offers free recycling of its branded products to business users. Detailed information is available at www.poly.com/us/en/company/corporate- responsibility/environment.

Getting Help and Copyright Information

GETTING HELP
For more information about installing, configuring, and administering Poly/Polycom products or services, go to the Poly Online Support Center. Poly 345 Encinal Street Santa Cruz, California 95060 © 2022 Poly. All trademarks are the property of their respective owners.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals