NEWSKILL ICARUS 24Inch FHD Resolution Gaming Monitor User Manual

NEWSKILL ICARUS 24Inch FHD Resolution Gaming Monitor

Important Safety Precautions

1. Please read all the instructions carefully before using this product.
2. BE SURE TO unplug the power cord when cleaning LCD. Never clean it with liquid detergent or spraying detergent, but wipe it with wet soft cloth. If it is still not clean, please use special detergent for LCD.
3. DO NOT use accessories not authorized by the manufacturer, other wise they may incur danger.
4. When disconnecting the power cord of display or power adapter, always remember to hold the plug instead of puling the wire to unplug the power cord.
5. Keep the display away from water sources such as bath tub, washbasin, sink or washing machine.DO NOT place the display on wet floor or near a swimming pool, or press LCD surface with fingers or hard objects.
6. The grooves and openings on the back and bottom of the shell are for ventilation purpose and also for guaranteeing the reliability of the elements and preventing them from overheating; in order to prevent the vents from blocking; DO NOT place the display on bed, sofa, carpet or other similar surfaces; DO NOT place the display near to or on heat radiator or heater; DO NOT put the display into embedded device, unless it is provided with adequate ventilating equipment.
7. Only the type of power source indicated on the nameplate applies to this display. If you have any questions on the type of power source you use, please consult the dealer of the display or local administration of power supply.
8. For safety, the display or the power adapter is equipped with three-pin plug power cord. The third pin of this plug is for grounding, and only applicable to socket that is correctly grounded. In case that your socket is not available for the plug, please contact electrician to replace the socket.
9. Since there is high voltage or other risks when the shell is opened or moved, please DO NOT repair the display by yourself, but request qualified maintenance staff to carry out.
10. In one of the following cases, please unplug the display or the power adapter and ask qualified maintenance staff for help:
    • a. The power cord or the plug is impaired or worn.
    • b. The display falls off or the shell is damaged.
    • c. The display is obviously abnormal.
11. Please place the display in a cool, dry and well ventilated place.
12. Store the display in temperature range of -10°C~60°C, beyond which the display may be damaged permanently.

Power & Electrical Warnings

• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
• The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
• Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
• To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 5A.
• The wall socket shall be installed near the equipment and shall be easily accessible.

Read the safety instructions carefully and thoroughly.
All cautions and warnings on the device or user’s manual should be noted. Refer servicing to qualified personnel only.
Keep the User’s Guide that comes with the package for future reference. To prevent fire or shock hazard, keep this device away from humidity and high temperature. Lay this device on a reliable flat surface before setting it up. Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet. Do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet. Always disconnect the power cord or switch the wall socket off if the devicewould be left unused for a certain time to achieve zero energy consumption. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
The ventilator on the device is used for air convection and to prevent the device from overheating. Do not cover the ventilator. Do not leave the device in an unconditioned environment with a storage temperature above 60OC or below -20OC, which may damage the device.
NOTE: The maximum operating temperature is around 40OC.
When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
Always keep strong magnetic or electrical objects away from the device.
If any of the following situations arises, get the device checked by service personnel: The power cord or plug is damaged.
Liquid has penetrated into the device.
The device has been exposed to moisture.
The device does not work well or you can not get it work according to user’s manual. The device has dropped and damaged.
The device has obvious sign of breakage

Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:

1. Take a 10-minute break for every 30 minutes of screen time.
2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day

Do not place the monitor in rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/or mechanical hazards.

Operation

• Keep the monitor out of direct sunlight and away from stoves or any other heat source.
• Keep the monitor out of water source
• Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes.
• Do not knock or drop the monitor during operation or transportation.

Maintenance Guidelines
CAUTION

• Do not place the monitor in rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/or mechanical hazards.
• Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.

Caring for Your Monitor

• To clean your screen, slightly dampen a soft, clean cloth with water.
• If possible, use a special screen-cleaning tissue or solution. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
• Use a slightly dampened, warm cloth to clean the frame. Avoid using detergent of any kind as some detergents might leave a milky film on the plastics.
• Unplug the monitor if you are not going to use it for an extendedperiod of time.
• To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. If your monitor gets wet, wipe it with dry cloth as soon as possible.

Product Description

Packing list
Please check the following items in the packing case before installation: If any of above items is missing, please contact with the dealer.

Product Overview

Monitor Buttons

Explanation of indicators Indicator: A steady blue light indicates that the power is on and the monitor is operating normally. Blue light flashes to indicate There is no video source and no horizontal or vertical signal or low voltage is detected. Make sure your computer It is turned on and all video cables are fully plugged in and/or connected.

Installation of base

Keep the foam underneath the monitor before attaching the stand.

1. Open the package, take out the product with foam still attached, and gently place it on adesktop or table.

2. Take out the support rod and the base, and lock the support with the thumbscrew of the base. (see below)

3. Remove the upper foam cover and place the machine on a flat surface
   Connect the bracket rod to the monitor with screws.

4. Put the bracket decoration cover back to the screw position.

Installation of mount

1. Open the package, take out the product with foam still attached, and gently placeit on a desktop or table. Remove the extra parts and the foam covering the backof the monitor. Press the release button to remove the stand plate.lf the monitorwas already attached to the stand, remove the stand.
2. Remove the original screws from the opening on the back of the monitor. Mount the monitor to the wall or fixture as needed. Remember to use the provided wall mounting screws when installing the monitor. Please place the screws correctly, as shown in the figure below.
3. Hang the assembled product on a hard wall. Do not pinch the screen with your hands during the hanging process to avoid damaging the screen.

Connectivity Options

• Connecting the power cable
  Please connect the power adapter to the power cable, connect the power adapter plug to the corresponding power port of the monitor, and then connect the power cable to a properly grounded power outlet.

• Connecting your earphones
  Connect audio outputting devices such as earphones to the AUDIO OUT interface .

• HDMI connectivity
  Use the HDMI cable to connect the HDMI IN interface of the product to the HDMI OUT interface of a PC.

• DPconnectivity
  Use the DP cable to connect the DP IN interface of the product to the DP OUT interface of a PC.

OSD Menu

The On-Screen Display (OSD) is used to adjust preferences and settings for the monitor itself. It will appear in the lower right corner once we activate it.

When using the monitor for the first time, settings will automatically adjust to optimal settings according to your computer’s configuration and parts etc.

1. Press one of the buttons (M, E, ) to activate the browser window.
2. Press M to enter the OSD screen.
3. Press or to navigate between functions.
   • The current selection will be highlighted, press M to access the sub-menu or select.
   • Navigate between the options with or and advance in the submenus with M button.
4. Press E to exit the current screen.

OSD Menu Functions

BRIGHTNESS

| BRIGHTNESS| 0-100
CONTRAST| 0-100
ECO| STANDARD, TEXT, GAME, MOVIE, FPS, RTS
DCR| ON/OFF

Imagen

| H. POSITION| 0-100
V. POSITION| 0-100
CLOCK| 0-100
PHASE| 0-100
ASPECT| WIDE, 4:3, AUTO
COLOR TEMP.| COLOR TEMP.| WARM, COOL, USER

OSD SETTING

| LANGUAGE| EPNOGRTLIUSGHU/FÊRSA/TNUÇRAKISC/ED/EPUOTLSSCKHI//N简ED体E中RL文AN/DITSA/LРIAУСNСOК/EИSЙP/A한Ñ국OL// 日本語
OSD H. POS.| 0-100
OSD V. POS.| 0-100
OSD TIMEOUT| 0-60
TRANSPARENCY| 0-100

RESET

| IMAGE AUTO ADJUST|
COLOR AUTO ADJUST|
RESET|

OTHER

| SIGNAL SOURCE| VGA, HDMI, DP
MUTE| ON/OFF
VOLUME| 0-100
LOW BLUE RAY| 0-100
OVERDRIVE| ON/OFF
Adaptive Sync| ON/OFF

Technical Specifications of Product

Audio
Speakers| No
Audio output| Yes
Accessories
Power cable| Yes
Power adapter| Yes
HDMI Cable| No
DP Cable| Yes
Additional functions
Low Blue Light| Yes
Physical Dimensions
Dimensions (with Stand)| 538.8 x 210.0 x 397.9mm
Dimensions (without Stand)| 538.8 x 91.2 x 322.4mm
Net Weight| 3,9Kg
Gross Weight| 5,4Kg

MORE INFORMATION AT www.newskillgaming.com

References

• Newskill Gaming - The Best Gaming Peripherals

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>