PET GEAR PG8650NZ No-Zip Excursions Pet Stroller Instruction Manual
- June 7, 2024
- PET GEAR
Table of Contents
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
NO-ZIP EXCURSION PET STROLLER
PG8650NZ
Interior Dimensions:
26″L x 15″W x 20″H
To see our full line of products, visit us online at:
www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 – Eastern
Standard Time 8 am-3 pm, Monday through Friday
PARTS LIST
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
BACK WHEEL ASSEMBLY
Step 1. Hold down lock release button shown in Figure A and slide back wheel
into axle shown in Figure B.
When the wheel meets the stroller, let go of the lock release.
Step 2. Pull-on wheel to make sure the wheel is engaged.
Repeat on another side.
When finished it should look like Figure C.
To Remove Back Wheels :
Hold down the lock/release button (Figure A) and pull the wheel off.
FRONT WHEEL ASSEMBLY
Step 1. To attach the front wheel, hold down on the wheel release button as shown in Figure D.
Step 2. While holding down the wheel release button, insert the metal post on the wheel and push down until the wheel meets the stroller (Figure E.) Let go of the wheel release. Pull up slightly on the wheel to be sure it’s locked in place. Repeat for another front wheel.
To Remove Front Wheels :
Hold down the wheel release button and pull the wheel out.
STROLLER ASSEMBLY
When all wheels are on the stroller, carefully place the stroller on all 4 wheels and begin to pull up on the handle to unfold the stroller shown in Figure F.
As you unfold the stroller, straighten the side latches until they lock in the place shown in Figures G and H. You will hear a click when the slide latches are engaged.
To adjust the handlebar, pushbuttons are located on each side of the handlebar and adjust to comfort shown in Figure I.
To open the front canopy on your stroller, simply push the release button located on the front of your stroller and lift the canopy shown in Figures J and K. To close the front of your stroller, clip the canopy back into the front of the stroller.
To open the back of your stroller, simply push the release button located on the back of your stroller and open the rear door shown in Figures L and M. To close the back of your stroller, clip the rear door into the back of the stroller.
| 
---|---
FRONT WHEEL LOCKING INSTRUCTIONS
Step 1. To use the stroller in the locked position for jogging, push wheel lockdown is shown in Figure N.
Step 2. To use the stroller in swivel position, push wheel lock up, shown in Figure O.
TO ASSEMBLE BACK TRAY
Step 1. To assemble the back tray, align the holes on the front of the tray with both of the knobs on the stroller, and secure into place by pushing forward, then down.
TO FOLD/PACK UP STROLLER
Step 1. Fold-down handlebar by pushing in the buttons located on each end of the handlebar shown in Figure P.
Step 2. Pull up on the hooked part of the side latch (Figure Q.) until the
latch disengages.
Step 3. Fold sides inward and push forward shown in Figure R.
LOOKING AFTER YOUR STROLLER
- Always store product in a clean, dry place.
- Not recommended for use on the beach.
- Do not put heavy items on top of the stroller.
- Clean the frame by wiping it with a lightly oiled cloth.
- Do not use detergent or abrasives. Spot clean fabric with dry cleaning fluid or mild soap and warm water.
- To ensure easy maneuverability and to minimize wear and tear, (especially wheels, axles, and swivels), keep all moving parts clean and lubricated with WD40 ® or light machine oil.
- NOTE: Do not lubricate brake components or swivel locks.
- Regularly check a stroller for loose parts. These should be tightened or replaced.
WHEEL MAINTENANCE
- To clean and lubricate front and rear wheels, push out locking lever under wheel housing to release rear wheel.
- To ensure ease of maneuverability and to minimize wear and tear, keep all moving parts clean and lubricated with WD40 ® or light machine oil.
- Push wheelsets back on until they click and lock in position; pull on wheel housings to ensure they are secure.
- Push stroller back and forth and rotate swivels around to work in lubricant.
- Clean the rear wheel assembly and the rest of the frame with warm, soapy water; clean off with warm water and dry thoroughly.
- NOTE: Do not lubricate brake components or swivel locks.
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous
animals that dig, chew or paw aggressively. Do not leave your pet unattended.
PET GEAR is not liable for any damage caused by aggressive, destructive,
immature, or untrained animals. Do not use near an open or exposed flame.
Failure to follow these warnings and the instructions could result in serious
injury or death.
- Do not carry additional bags, goods, or accessories in or on stroller except as recommended in the manufacturer’s instructions.
- Recommended use of an approved safety restraint correctly fitted and adjusted.
- Do not leave pet unsupervised in the stroller.
- Before making adjustments to the stroller ensure that the pet’s body is clear of any moving parts.
- Do not hang bags from handles as this may cause the product to become unstable.
- Do not use on escalator or stairs; fold the stroller and carry.
- Put on brake whenever you park the stroller.
- Ensure the stroller is completely erected and check that all locks are engaged before placing pet in the stroller.
- Do not overload as the stroller may become unstable; the maximum weight of a pet using this stroller is not to exceed 150 lbs.
REPLACEMENT PARTS
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
192 Sheldon Avenue West Rutland, VT05777 877-752-9123 www.petgearinc.com
N0-ZIP EXCURSION PET STROLLER • PG8650NZ
Documents / Resources
| PET
GEAR PG8650NZ No-Zip Excursions Pet
Stroller
[pdf] Instruction Manual
PG8650NZ, No-Zip Excursions Pet Stroller
---|---