YAMAHA NS-IW660 In-Wall Speaker Owner’s Manual
- June 7, 2024
- Yamaha
Table of Contents
YAMAHA NS-IW660 In-Wall Speaker Owner’s Manual
CONSUMER PRECAUTIONS
Read these precautions carefully before installing your NS-IW660 speaker.
- Before you begin installation, read this owner’s manual and consult your local building codes. If you have any doubts or reservations, contact your dealer or a qualified audio/video installer.
- YAMAHA recommends installing the speaker only in two-by-four wood frame or similar construction. The instructions provided in this owner’s manual are intended specifically for this type of wall construction.
- When installing your NS-IW660 in-wall speaker, be aware of the product weight (See specification page) and the sturdiness of the material into which you are installing the speaker.
- Be aware of any concealed studs, electrical wiring or plumbing in the wall or ceiling into which you are installing the speakers. If you are not sure of a safe way to install these speakers, consult a professional installer or a building contractor.
- Never touch the speaker with your hands or expose it to excessive physical shock. If it is dented or bent, the sound will be distorted.
- Lower the power amplifier/receiver volume control before changing input sources. Never change input sources (for example, FM to CD) at high listening levels. Always turn the receiver/amplifier unit off when installing or removing any cables.
- Anytime you note distortion, reduce the volume control on your power amplifier/receiver to a lower setting. Never allow your power amplifier to be driven into “clipping.”
- Secure placement or installation is the owner’s responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers.
WARNING:
Installation shall be in accordance with the applicable section of the National Electrical Code, ANSI/NFPA 70, and/or the National Fire Alarm Code, ANSI/NFPA 72, as applicable. The wiring method and compartment shall be such as not to interfere with the operation of the speaker.
UNPACKING
After unpacking, check that the following items are contained.
TOOLS NEEDED
SPEAKER PLACEMENT
- Stereo
For best stereo performance, install the left and right speakers at equal distance from the listening position. Each speaker should be separated by a distance of 6- 10 ft. The center of the speaker should be placed at the listener’s ear level.
- Home Theater
Install the left and right front speakers on either side of your TV, with the center of the speaker at the listener’s ear level. The center channel speaker can be installed horizontally above or below the TV. Surround speakers should ideally be placed behind the listening area, at least as far apart as the front speakers and up to 2 additional feet apart per side. The height of the speaker should be at a minimum of ear level or preferably somewhat higher.
INSTALLATION
Before installation, check to ensure that the area you are installing the speaker is free of any wall studs, either by tapping the wall or using a stud finder.
If you wish to paint the speaker frame and grille, please refer to page 7 “PAINTING THE SPEAKER FRAME AND GRILLE” before proceeding.
-
Position the cutout template where you are installing the speaker. Make sure the template is level, then trace around the template with a pencil.
-
Drill a pilot hole in the center outline you traced.
-
Insert the bent coat hanger wire into the hole. Then slowly rotate to check for any obstruction. If there is any obstruction, patch the hole and select another location.
-
Cut the wall along the outline you traced.
-
Run high quality speaker cable from your receiver to the speaker. Leave a few extra feet of cable.
Note: You can insulate the cavity by placing a sheet of fiberglass insulation around the speaker components to improve speaker performance.
-
Connect the speaker cable to the speaker and your receiver. Please refer to page 6, “CONNECTIONS” section for detailed instructions.
-
Place the speaker into the wall. Loosen each mounting screw by turning it counterclockwise one complete turn. This will release the mounting clamp from its shipping position.
-
Tighten each of the four mounting screws evenly until the mounting clamp grips the wall “finger tight.” Now tighten each screw one additional turn only. This will secure the speaker firmly to the wall.
Note:
We recommend using only hand tools as powered drivers may over-tighten the
screws.
Note:
You can swivel the tweeter and the midrange speaker to direct high
frequency sounds precisely toward the listening position by gently pressing
the outer edge of the tweeter mount.
- Attach the grille to the frame.
Note:
For permanent grille attachment, application of the supplied glue strips is recommended.
Recommended Glue Strip Location
CONNECTIONS
- Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of the receiver.
- Connect the (+) terminals on the receiver and speakers using the corresponding side of the cable. Connect the (-) terminals on both components using the other side of the cable.
Notes:
- Make sure that the bare wires are not touching each other as this could damage the speaker and receiver.
- Connect one speaker to the left terminals of your receiver, and another speaker to the right terminals, making sure not to reverse the polarity (+, -). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass.
• How to connect
- Hold down the knob.
- Insert the bare wire. Remove the insulation coating at the extremity of each speaker cable by twisting the coating off.
- Release the knob. Test the connection by pulling lightly on the cable at the terminal.
• When using a banana plug
Insert the banana plug into the terminal. Test the connection by pulling lightly on the cable at the terminal.
PAINTING THE SPEAKER FRAME AND GRILLE
The speaker frame and grille can be painted to match your room decor. Use high quality spray paint and select a well-ventilated area before proceeding.
• Painting the frame
- Remove the speaker from the wall if it is already installed. Also, remove the grille from the baffle.
- Mask the speaker components and the baffle with the supplied paint protective cover.
- Apply the paint to the frame.
• Painting the grille
- Carefully remove the grille from the speaker, if attached.
- Apply the paint to the grille. Make sure that the grille holes remain free of paint. Clogging the holes with paint may diminish the sound quality.
ADJUSTING THE HIGH LEVEL VOLUME CONTROL
If you wish to adjust the tonal balance to suit your taste or your listening environment, use the High Level control on the front panel to change the high frequency volume level. Turn the control clockwise to boost and counterclockwise to cut over a range of -6 dB to+3 dB.
SPECIFICATIONS
Speaker:
6.5″ Kevlar cone woofer
1.6″ Aluminum dome midrange
1″ Titanium dome tweeter
Frequency Range: 50Hz to 28KHz
High level Frequency Control: +3dB to-6dB
Impedance: 8 ohms
Nominal Input: 50 W
Maximum Input: 150 W
Sensitivity (dB/2.83v. 1m): 88 dB
Crossover Frequency: 3,500Hz and 7,000Hz
Dimension (H x Wx D): 11.9″ x 8.9″ x 3.8″ (303.6 x 226.4 x 96.45 mm)
(Mounting depth): 3.1″ (77.7mm)
Weight: 4.7 lbs (2.1 kg)
Magnetic Shielding: No
*Specifications subject to change without notice due to product improvements.
Yamaha Corporation of America is proud of the experienced craftsmanship that goes into each and every YAMAHA Loudspeaker. YAMAHA sells its products only through a network of high quality, specially authorized dealers and is pleased to offer the following Limited Warranty, which applies only to products purchased by consumers directly from our authorized dealers. We suggest that you read the Limited Warranty thoroughly, and invite you to contact your authorized YAMAHA dealer or the Yamaha Corporation of America Service Department if you have any questions.
CUSTOMER SERVICE
YAMAHA CORPORATION OF AMERICA
6600 ORANGETHORPEAVE., BUENAPARK, CA 90620-1373
http://usa.yamaha.com Phone: (800)292-2982
Do not return any product to the above address without a written Return Authorization issued by YAMAHA.
Documents / Resources
|
YAMAHA NS-IW660 In-Wall
Speaker
[pdf] Owner's Manual
NS-IW660, In-Wall Speaker
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>