VISA LIGHTING CB1851 Series Sole Lighting Mirror Instruction Manual

: June 7, 2024
: VISA LIGHTING

Table of Contents

VISA LIGHTING CB1851 Series Sole Lighting Mirror
Dimension
CLEANING AND CARE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Tools Required
FRAMING INSTRUCTIONS
Install LED assembly
Contact
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VISA LIGHTING CB1851 Series Sole Lighting Mirror

Model: CB1851, CB1853
Fixture Family: SOLE
Document Description: Installation Instructions for Sole Series Mirrors

Installation instruction video: https://youtu.be/Wb9MbmjCKtk

Dimension

Sheet 1: COVER PAGE/CLEANING AND CARE INSTRUCTIONS
Sheet 2: IMPORTANT SAFETY INSTRUCTIONS
Sheet 3: SHIPPING NOTES + TOOLS REQUIRED
Sheet 4: FRAMING INSTRUCTIONS
Sheet 5: Use the provided cardboard template. Drill holes/ Trace centre cut
Sheet 6: Cut and install wood blocking
Sheet 7: Remote-mounted driver box
Sheet 8: Install LED assembly + Install lens frame assembly
Sheet 9: Wiring Diagram

CLEANING AND CARE INSTRUCTIONS

Use care when cleaning this LED Luminaire. The mirror is made of polycarbonate. Do not use abrasive cleaners, chemicals or solvents which may result in surface damage to the lens or housing.
The luminaire can be cleaned with mild soap and warm water. Use a microfiber cloth to clean the mirror surtace.

When using electrical equipment, basic safety precautions should always be followed, including the following:

Warning

Read all instructions carefully before installing and save for future use.
Make sure all connections are following the National Electrical Code and local regulations.
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
Service should be performed by qualified personnel.
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of burns, fire, electric shock, or injury to persons:

Use this illuminated mirror for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
Install per applicable local and national codes.
Risk of Death or Serious Injury:
Do not install near pools, ponds, or other bodies of water.
To reduce the risk of Ligature:
Ensure all fasteners are fully seated and do not protrude from the mirror frame.
Apply a pick-proof sealant around the perimeter of the frame at the mounting surface.
Ingress protection:
Ingress protection for fixtures is from the outside only. The sole is not sealed from the wall cavity.
Wall gasket must be installed on a smooth flat surface (i.e. acrylic or vinyl for wash-down applications) for an IP65 rating. Rough, textured, round or otherwise curved surfaces require additional sealing measures (not provided).
Grounding Instructions:
The remote driver box must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product. Electrical Ratings: 120-277 VAC, 50/60Hz, 50 W MAX
Wood blocking (furring strips)
WARNING- Wood blocking must be installed as described to achieve rated impact resistance.
Impact ratings are void if wood blocking is not installed as described

SHIPPING NOTES Each Sole luminaire will be bulk shipped in 5 components:

Cardboard wall template
Lens frame assembly
Painted Pin-in-Torx screws
LED assembly
Remote Driver Box

Note: CB1853 (OVAL) shown below, CB1851 (RECTANGULAR) is shipped the same way

Tools Required

Jigsaw
Drill
T20 Pin-in-Torx drive
Philips screwdriver
Level
Pencil

Not included

2×4 Wood blocking
Wood blocking mounting screws
Wiring between LED assembly and remote driver box

FRAMING INSTRUCTIONS

No parts are required from Visa before installing the wallboard. Wood blocking is installed after cutting a hole in the wall for LED assembly.
For ADA installation – install mirror framing such that the lower edge of the mirror surface is per code. The cardboard template supplied outlines this surface.
The Center Wall Stud is required for impact resistance. Adjacent Studs are to be positioned as follows to provide necessary impact resistance and avoid interference with wood-blocking
CB1851: 11-3/4″ to 16″ away from center
CB1853: 12-1/2″ to 16″ away from center
Deviations from this may be acceptable for low-risk or non-behavioural health areas where the impact resistance is of lesser concern, consult the facility for acceptance.

Use the cardboard template provided. Drill holes/ Trace centre cut

Remove the perforated, cross-hatched cut-out section.
Level and tape the template to the wall at the correct height
Using a pencil, trace the wall cutout
Use a 1/8″ diameter drill to mark hole locations per the template.
Remove template
Cut wall surface hole as traced

Cut and install wood blocking: Wood 2 x 4 is required to make the 6 wood blocking pieces (Cross-Sectional Dimensions 1.5″ x 3.5″)
CB1851: 91″ total / CB1853: 94″ total

Instructions:

See dimensions below to make pieces, can also use a carboard template
Start screws in the wallboard, 2 for each piece of wood. (Locations marked from the cardboard template.)
Insert wood through a hole in the wall surface and align it with the edge of the cutout
Screw wood blocking in place

Remote Mounted Driver box (RMD) (Components may vary depending on options ordered)

It is recomended that the remote driver box is installed in a location that is accessible to service the drivers without disturbing the patient room or mirror.
For locations that are at low risk or non behavioral health such that it was decided not to use pick-proof caulk around the mirror, the Remote Driver Box may be installed directly to the recessed housing.
Mount remote box per local and national codes, use fasteners appropriate for the mounting surface (by others).
Make all wire connections per local and national codes.

Install LED assembly

Attach LED assembly over top of wallboard using the screws provided (x3). Use the hole locations marked from the wall template.

Install lens frame assembly

Attach using the provided screws. Use the hole locations marked from the wall template. Screws need to secure into the wood blocking. Screws are long enough for wall surfaces from 5/8″ to 1- 3/4″ thick. **See note below for a special circumstance.
For areas at a high-risk of ligature, apply pickproof caulk around the Frame perimeter at the wall surface.

Wiring diagram

Body light and optional nightlight LED are controlled on separate circuits, only the Bodylight is dimmable via 0-10V dimming
Ensure that the LEDs are connected to the correct driver:
- Body light LEDs to driver labelled “DriverA”
- Optional nightlight LEDs to driver labelled “DriverNGT”