Godox MoveLink II 2.4GHz Wireless Microphone System Instruction Manual

Godox MoveLink II 2.4GHz Wireless Microphone System

Forward

Thank you for purchasing Godox MoveLink 2.4GHz wireless microphone system MoveLink II. These products are suitable for video recording, journalistic shooting, audio recording, etc. Please read this manual carefully before using to make sure the correct operation and exert the optimum function.

Features

1. Adopt globally accepted 2.4GHz wireless and frequency-hopping technology to avoid the same frequency disturbance, which can be used in WIFI and Bluetooth simultaneously (may be influenced in occasions with multiple WIFI nodes).
2. Clear, stable and lossless sound quality, the addition of digital noise reduction function.
3. The maximum wireless distance up to 100m.
4. With TFT display to show the parameters set.
5. Support 3.5mm Earphone real-time monitoring.
6. With output volume control and silence function.
7. Stable match of transmitting and receiving.
8. Supports two-way transmitting and one-way receiving.
9. Freely switch mono or stereo channel to offer more output options.
10. Two lithium battery charging methods through USB port or MoveLink II charging case connected to power supply.

Warning

• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
• Always keep this product dry. Do not use in rain or in damp conditions.
• Keep out of reach of children.
• Do not use the device in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings.
• Do not leave or store the product if the ambient temperature reads over 50°C.
• Turn off the devices immediately in the event of malfunction.

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Names of Parts

Movelink II TX (Transmitter)

1. Built-in Microphone
2. 3.5mm Audio Port
3. Power Switch Button
4. Mute Button
5. Working Indicator
6. DNR/Pair Button
7. TFT Display
8. USB Type-C Port

MoveLlnk II RX (Receiver)

1. 3.5mm Audio Sync Monitoring Port
2. 3.5mm TRS Audio Output Port
3. Power Switch/Switch Volume Setting Button
4. Sound+/-
5. Working Indicator
6. Pairing Button
7. TFT Display
8. US8 T ype-C Port

Functions and MoveLink II TX (Transmitter)

Display

1. Connecting channel (A means connecting to A channel)
2. Connecting state(The lower picture with grey interface means unconnected, while the upper picture with colorful interface means connected)
3. Battery level
4. Silent icon
5. Soundbyte indication
6. Noise reduction indication

Function Introduction

• Power switch: long press the power switch to power on or off. In the state of power-on, if there is USB Type-C Cable inserted, long press the power switch to enter standby state and the charging animation will be displayed. In standby state, long press the power switch to power on.Long press the power switch and DNR/pair button at the same time in power down state can clear the previous pairing information.
• Short press the TX mute button to switch on or off silent mode.
• Short press the DNR/pair button to switch on /off digital noise reduction function,long press to match the receiver. The indicator will light blue when successfully matched.
• Charge the products through USB Type-C port directly. The charging animation will be displayed in charging.

lnstallatlon Method
Using built-in microphone: Through the back clip Install the transmitter on the collar through the back clip, aiming the built-in microphone towards the sound source direction. For achieving better invisibility during usage, it is recommended to fix the back clip towards the outside.

Through the magnetic mount
Back clip of Movelink transmitter and receiver with magnetic which can be mount on smooth metal iron surface.The including iron sheet can strongly absorb the back clip, allowing the transmitter or receiver to be hidden in the clothes. Hold the transmitter in one hand with the back clip facing out and put it into the clothes. With the other hand, cover the iron sheet on the clothes to absorb the back clip. After the back clip is strongly sucked, you can let them go. Note that single-layer clothes can be strongly adsorbed. Thicker, ultra-thick or multilayer clothes will have weak adsorption capacity and will not be able to adsorb. In this case, please do not use this installation method.

Using External Microphone:
Insert the 3.5mm lavalier microphone into the transmitter’ s 3.5mm audio port and lock it tightly. Clip the transmitter onto the belt by back clip and clip the lavalier microphone on the other end onto the collar. When using the external microphone, the built-in microphone will be automatically turned off .

Movelink II RX (Receiver)

Screen Display

1.  A/B channel transmitter’s battery level
2. A/B channel’s soundbyte dynamic display
3. Sound channel selection display
4. A/B channel’s volume adjustment display
5. Pairing interface
6. Connection State (The right picture with grey interface means unconnected, while the left two pictures with colorful interface means connected)

Function Introduction

Power Switch:
long press the power switch to power on or off. In the state of power-on, if there is USB Type-C inserted, long press the power switch to enter standby state and the charging animation will be displayed. In standby state, long press the power switch to power on. Long press the power switch and pair button at the same time in power down state can clear the previous pairing information.

Volume Adjustment:

1. In dual sound setting mode, short press the ·sound+/-” button once to increase or decrease the A/B transmitter’ s sound volume simultaneously by 1 unit; long press the ·sound+/-· button to increase or decrease the A/B transmitter’s sound volume gradually.
2. Switch to mono channel sound setting: Short press the power switch button POWER to separately adjust the volume of· A channel” and ·s channel” . The channel with blinking figures can be adjusted volumes and will be switched to dual channel adjustment if there are no operations after 5 seconds. Mono channel sound adjustment is same as (1) above, short press the ·sound+/-” once to increase or decrease the volume by 1 unit, long press the ·sound+/-· to increase or decrease the volume gradually.
3. There are 16 levels of volume adjustment: -5dB-10db.
   • Long press the pairing button to match the singles of transmitters. The left channel will automatically receive A transmitter’s singles while the right channel will receive B transmitter’ s. Short press the pairing button to select mono channel and stereo channel.
   • Charge the products through USB Type-C port directly. The charging animation will be displayed in charging.

Installation Method

Install the receiver onto the camera’s hot shoe and fix it through the back clip. And connect the receiver with the camera by a 3.5mm TRS-TRS audio connect cable. Then, insert your earphone plug into the 3.5mm Audio Sync Monitoring Port to monitor.

Port and Indicator

Ports:

• Transmitter LINE IN: audio singles input
• Receiver LINE Out: audio singles output
• Receiver Audio Sync Monitoring Port: insert the earphone plug into monitoring port

Indicator:
Working indicator: the indicator will display green in normal working state.

1. Transmitter
   • In the standby state, the indicator will be off.
   • In the boot-up state, the indicator will be orange in non-connection, be blue in connection.
   • During the pairing, the indicator will blink in red for two times circularly.
2. Receiver
   • In the standby state, the indicator will be off.
   • In the boot-up state, the indicator will be orange in non-connection, be blue in connection.
   • During the pairing, the indicator will blink in red for two times circularly.

What’s in the Box

Movelink II Charging Case (ML II-C3)

There are three charging bases in the charging case, which can charge three transmitters or receivers of Movelink II system after being connected to power supply.

Note: Movelink II Ml do not include Movelink II Charging Case while Movelink II M2 includes a Movelink II Charging Case.

• Movelink II Charging Case Schematic Diagram of Charging: The indicator will display yellow during the charging process and turn to green when being fully charged.

Movelink II system has two charging ways:

• being charged from USB Type-C cable;
• being charged through Movelink II Charging Case.

Technique Data

Product design and specifications are subject to changes without notice.

Troubleshooting

Unable to receive the audio signal. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the microphone or earphone is well connected, or if the devices are set to the correct mode. Check if the transmitter is set to mute mode or not. Signal disturbance or shooting interference. Change a different channel of the transmitter and receiver. Operation audio distance limited or signal missing. Check if batteries are exhaust­ed. If so, replace them.

Maintenance

Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess stress. Keep dry. The product isn’t water-proof. Malfunctions, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity. Avoid sudden temperature changes. Condensation happens if sudden temperature changes such as the circumstance when taking the product out of a building with a higher temperature to outside in winter. Please put the product in a handbag or plastic bag beforehand. Keep away from a strong magnetic field. The strong static or magnetic field produced by devices such as radio transmitters leads to malfunction. Changes made to the specifications or designs may not be reflected in this manual.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
• the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Warning

• Operating frequency: 2402MHz – 2480MHz
• Maximum EIRP Power: 5.328dBm(TX), 2.791dBm(RX)

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.For more information of DoC, Please click this web link: https://www.godox.com/DOC/Godox_MoveLinklI_Series_DOC.pdf  The device complies with RF specifications when the device used at Omm from your body.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and saf&-keep it. Thank you!

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional
items, giveaways, and additional accessories attached.etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time.and the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases: CD.

1. The product or accessory has expired Its warranty period;
2. Breakage or damage caused by Inappropriate usage, maintenance or preservation, such as Improper packing, Improper usage, Improper plugging In/out external equipment, falling off or squeezing by external force, contact­Ing or exposure to the Improper temperature, solvent, acid, base, flooding and damp environments, etc;
3. Breakage or damage caused by non-authorized Institution or staff In the process of Installation, maintenance, alternation, addition and detachment;
4. The original Identifying information of the product or accessory Is modified, alternated, or removed; (ID. No valid warranty card;
5. Breakage or damage caused by using Illegally authorized, nonstandard or non-public released software; (D. Breakage or damage caused by force majeure or accident;
6. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that are beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion, and consumption are not breakage within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

GODOX Photo Equipment Co.,Ltd.

• Add. Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Baoan District, Shenzhen 5181 03, China
• Tel +86-755-29609320{8062)
• Fax +86-755-25723423
• Email. godox@godox.com
• www.godox.com
• Made in China I 705-ML2C30-00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>