VISA LIGHTING CB5301 Air Foil Wall Mount Instruction Manual

June 4, 2024
VISA LIGHTING

VISA-LIGHTING-LOOG

VISA LIGHTING CB5301 Air Foil Wall Mount

WARNING

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

INDOOR FIXTURE

VISA-LIGHTING-CB5301-Air-Foil-Wall-Mount-FIG1

NOTE: LAMP HOUSING IS NOT SHOWN (FOR REFERENCE ONLY) TO HELP WITH INSTALLING FIXTURE TO THE WALL. REFER TO PAGE 5 FOR COMPLETE FIXTURE DETAILS.

DO NOT REMOVE LAMP HOUSING FROM WALL MOUNTING ARM ASSEMBLY

  1. Remove decorative cover and wire access cover. Remove mounting plate and save nuts and washers.
  2. Locate auxiliary mounting holes and install anchors (by others). Secure mounting plate to junction box. Secure mounting plate to wall using auxiliary mounting holes. Attach with screws into wall anchors (by others).
  3. Align fixture with mounting plate studs on back plate. Slide fixture onto wall mounting plate. Install metal washer and 1/4-20 nut on to mounting plate studs. Make sure fixture is supported in position until 1/4-20 nuts have been installed. Tighten 1/4-20 nuts to draw housing flush with wall.
  4. Make all electrical connections in accordance with local and national electric codes.
  5. Reinstall access cover and decorative cover.

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

INDOOR FIXTURE

VISA-LIGHTING-CB5301-Air-Foil-Wall-Mount-FIG2

NOTE: LAMP HOUSING IS NOT SHOWN (FOR REFERENCE ONLY) TO HELP WITH INSTALLING FIXTURE TO THE WALL. REFER TO PAGE 5 FOR COMPLETE FIXTURE DETAILS.

DO NOT REMOVE LAMP HOUSING FROM WALL MOUNTING ARM ASSEMBLY

  1. Remove decorative cover and wire access cover. Remove mounting plate and save nuts and washers.
  2. Locate auxiliary mounting holes and install anchors (by others). Secure mounting plate to junction box. Secure mounting plate to wall using auxiliary mounting holes. Attach with screws into wall anchors (by others).
  3. Align fixture with mounting plate studs on back plate. Slide fixture onto wall mounting plate. Install metal washer and 1/4-20 nut on to mounting plate studs. Make sure fixture is supported in position until 1/4-20 nuts have been installed. Tighten 1/4-20 nuts to draw housing flush with wall.
  4. Make all electrical connections in accordance with local and national electric codes.
  5. Reinstall access cover and decorative cover.

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

OUTDOOR FIXTURE

VISA-LIGHTING-CB5301-Air-Foil-Wall-Mount-FIG3

DO NOT REMOVE LAMP HOUSING FROM WALL MOUNTING ARM ASSEMBLY

  1. Remove decorative cover and wire access cover. Remove mounting plate and save nuts and washers.
  2. Caulk around auxiliary mounting holes and area on mounting plate where it connects to the junction box. See page 6 for caulking instructions.
  3. Locate auxiliary mounting holes and install anchors (by others). Secure mounting plate to junction box. Secure mounting plate to wall using auxiliary mounting holes. Attach with screws into wall anchors (by others).
  4. Align fixture with mounting plate studs on back plate. Slide fixture onto wall mounting plate. Install metal washers, rubber washers, and 1/4-20 nuts on to mounting plate studs. Make sure fixture is supported in position until 1/4-20 nuts have been installed. Tighten 1/4-20 nuts to draw housing flush with wall.
  5. Make all electrical connections in accordance with local and national electric codes.
  6. Reinstall access cover and decorative cover.

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

REFERENCE PAGE

VISA-LIGHTING-CB5301-Air-Foil-Wall-Mount-FIG4

EXAMPLE OF WHAT THE FINISHED PRODUCT SHOULD LOOK LIKE ONCE INSTALLED ON WALL. STYLE MAY VARY, BUT INSTALLS SIMILARLY ON ALL MODELS.

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting

CAULKING INSTRUCTIONS

FOR OUTDOOR MOUNTING ONLY

VISA-LIGHTING-CB5301-Air-Foil-Wall-Mount-FIG5

NOTES:

  1. CAULK AROUND JUNCTION BOX LOCATION ON MOUNTING PLATE AND AUXILIARY MOUNTING HOLES.
  2. CLEAN UP ANY EXCESS CAULK THAT HAS BEEN SQUEEZED OUT AFTER INSTALLING MOUNTING PLATE, (TO ENSURE PROPER FIT WHEN FIXTURE IS INSTALLED TO MOUNTING PLATE). THIS COULD CAUSE AN ISSUE WHEN INSTALLING FIXTURE IF NOT REMOVED.

When using electrical equipment, basic safety precautions should always be followed, including the following:

  • Read all instructions carefully before installing and save for future use.
  • Make sure all connections are in accordance with the National Electrical Code and local regulations.
  • To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
  • Service should be performed by qualified personnel.
  • These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

Model: CB5301, CB5303, OW5303
Fixture Family: AIRFOIL
Document Description: Installation Instructions for AIRFOIL

1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals