ZYXEL PoE12-30W PoE Injector Series User Guide

: June 6, 2024
: ZYXEL

Table of Contents

Connecting the PoE Injector
LEDs
Troubleshooting
Wall Mounting (Optional)
Warranty Card
- Purchase Information
- Certifications
Safety Warnings
Support Information
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

ZYXEL PoE12-30W PoE Injector Series User Guide

Connecting the PoE Injector

ZYXEL PoE12-30W PoE Injector Series User Guide ZYXEL PoE12-30W PoE Injector
Series

Connect an Ethernet device to the IN port of the PoE injector.
Connect a PoE-enabled device to the OUT port of the PoE injector.
Use the included power cord to connect the PoE Injector’s power socket to a power source (wall outlet or power strip).

LEDs

PoE| Green
On -PoE power is supplied.
---|---
PWR| Green
On -The system is receiving power and an Ethernet cable is connected to the OUT port.
Off -The system is off or has failed.

Troubleshooting

The PWR LED is off and/or power is not being supplied to my PoE-enabled device.

Check to see that the power cord is securely connect-ed to the PoE Injector and an appropriate power source. Make sure the power source is on and functioning properly.
Refer to the Connecting the PoE Injector section. Check that the Ethernet cables are connected properly and that you are using the correct type of Ethernet cable. Contact your local distributor if the problem persists.

Wall Mounting (Optional)

Wall Mounting

Warranty Card

Thank you for purchasing a Zyxel product. Zyxel has o reputation for delivering high quality, high performance products and services to our customers. We recommend that you now visit the Zyxel website and register your product online. This will mean you can receive the latest firmware, drivers and product related information. If you still hove further questions or enquiries related to the product, please contact our subsidiaries worldwide. Please note that warranty terms may vary by region. Full detailed information is available on our website, here: http://www.zyxel.com/support/warranty_information.shtml

Purchase Information

Zyxel Product Name:

Hardware Serial Number:

Date of Purchase:

(In certain countries, the warranty will be validated with seller’s signature and stamp):

Certifications

Federal Communications Commission (FCC) Interference Statement The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operations.

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

CE Mark Warning: This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Viewing Certifications
Go to http://www.zyxel.com.

Select your product on the Zyxel home page to go to that product’s page.
Select the certification you wish to view from this page.

Safety Warnings

Do NOT use this product near water, for example, in a wet basement or near a swimming pool.
Do NOT expose your device to dampness, dust or corrosive liquids.
Do NOT store things on the device.
Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. ‘Connect ONLY suitable accessories to the device.
Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.
Place connecting cables carefully so that no one will step on them or stumble over them.
Always disconnect all cables from this device before servicing or disassembling.
Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example,110V AC in North America or 230V AC in Europe).
Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord.
Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.
If the power adaptor or cord is damaged, remove it from the device and the power source.
Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.
Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.
Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.
Make sure that the cable system is grounded so as to provide some protection against voltage surges.
Make sure to connect the cables to the correct ports.
Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately.