ROCKVILLE RWM1203VH VHF Dual Channel Handheld Wireless Microphone System Owner’s Manual

ROCKVILLE RWM1203VH VHF Dual Channel Handheld Wireless Microphone System

Owner’s Manual

Rockville

Thank you for purchasing this Rockville Wireless Microphone System. Please read this installation guide carefully for proper use. Should you need assistance
please call our technical help line at 1-646-758-0144, Monday through Friday, 9am to 5pm EST.

IMPORTANT SAFETY INSTRUCTIONS

• To reduce risk of electric shock, never open the unit. There are no user-serviceable parts; refer service to an authorized Rockville service center.
• Do not expose this unit to any kind of moisture.
• Please ensure that the unit is situated in a properly ventilated area.
•  Make sure the unit is placed on a level and stable surface.

specs

FEATURES

• VHF Dual Channel Handheld Wireless Microphone System
• Large display on receiver + digital display on each mic
• Each mic is large and solid with a nice weighted feel
• Improved high performance wireless handheld microphone capsule
• Includes transmitter with two handheld, high sensitivity, unidirectional, wireless cardioid microphones
• Featuring a dual filter design to limit feedback and interference
• Ultra signal stability eliminates unwanted distortion
• Transmitter automatically links to receiver for ease of use
• Use two handheld mies at once
• Individual microphone volume controls.
• Low power consumption for longer battery life.

SPECIFICATIONS SYSTEM

Operating Range: 150 feet or more* Channel: Two Channel Frequency Range: 210MHz – 270MHz Frequency Response: 40Hz-18KHz S/N.:>103dB (1KHz-A)
Operating Temp: 14°F -122°F Oscillation Mode: Quartz Crystal Frequency Stability: ±0.005% Modulation Mode: VHF
Harmonic Radiation :< 63dBm RF Output Power: 1 0mW Power Voltage: AC11 0V- 60Hz Mic Battery: AA x 2.

RECEIVER

Sensitivity: (S/N=30dB) >2mV Audio Output Impedance: 6000 Audio Output Level.: 0-0.5V Power Supply: AC11 0V 60Hz
Current Consumption: s50mA Audio Out Connector: 1/4″ unbalanced

TRANSMITTER

Frequency Stability: ±0.005% RF Output Power: s1 0mW Modulation Mode: VHF Maximum Deviation Range: ±50KHz
Microphone Mode: Fixed Power Supply: AA/1 .5Vx2 Current Consumption: s35mA.

operating range is subject to environmental conditions. Results may vary.

Receiver (Front)

a. AntennaA
b. Antenna B
c. MIC A Volume adjustment knob
d. MIC B Volume adjustment knob
e. MIC A RF signal LED indicator
l,Mi%4ii~ttaJ►
f. MIC AAF signal LED indicator
g. LCD screen
h. MIC B AF signal LED indicator
i. MIC B RF signal LED indicator
j. Power on/off switch

Receiver (Back)

Microphones

a. Microphone windscreen
b. Power LED indicator
c. Power on/off switch
d. Low battery indicator
e. Battery compartment

Setup and operation

Most mixers and powered speakers have both a Microphone input and a line level input. For best performance of the wireless microphone system you should make sure that you run the cable from one the receiver outputs (XLR, 1 /4″ output) into the line input of the powered speaker or mixing board.

• The reciever should be placed in an area that is stable and least likely to shake the unit.
• The receiver should be at least 3· off the ground for optimal transmission.
• Connect the antenna, balanced cable AF line, and power supply provided.
• The antenna should extend vertically.
• Switch on the reciever.
• While the receiver is in stand-by, switch on the microphones.
• Adjust volume as necessary.

Troubleshooting

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible party name: Rockville
Address: 600 Bayview Ave,
Entrance A,
Inwood, NY 11096

Hereby declares that the product Rockville RWM1203VH VHF microphone kit complies with FCC rules as mentioned in the following paragraph:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RockvilleAudio.com
© 2020 ROCKVILLE // Features and specifications are subject to change and/or improvement without notice.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>