ROCKVILLE Wireless Microphone System RWM2603UR Owner’s Manual
- June 6, 2024
- RockVille
Table of Contents
OWNER’S MANUAL
RWM26O3UR
HIGH PERFORMANCE HAND-HELD WIRELESS DUAL-MICROPHONE SYSTEM
Who reads manuals? Instead, go to https://vimeo.com/454897844 or scan the QR code and watch a short video, which shows you how to set this item up and how to use it.
Thank you for purchasing this Rockville high-performance hand-held wireless
dual microphone system. Please read this owner’s manual carefully for proper
use of your Rockville RWM2603UR Wireless Microphone System. Should you need
technical assistance please call our technical helpline at
1-646-758-0144, Monday through Friday,
9am to 5pm EST.
Specs
FEATURES
- High-performance wireless hand held rechargeable microphone system
- Built in charging dock for microphones
- LED microphone charging LED indicator
- Includes RWM2603UR transmitter with (2) rechargeable hand held,
- High sensitivity, unidirectional, wireless cardioid microphones with re-chargeable batteries
- Professional rack mount design with LCD displays
- Featuring a dual filter design to limit feedback and interference
- Individual microphone volume control
- Comfortable ergonomic composite microphone construction
- Low power consumption for longer battery life
- AF/RF LED Indicators
- Ultra signal stability minimizes audio artifacts
- OSA technology: Locates, prioritizes, and selects the clearest frequency for the best sound quality
SPECIFICATIONS
Operating Range: 200″-260″(indoor), 160″-220″(outdoor)
Frequency Range: 500MHz-599MHz
Frequency Stability: ±0.005%
Modulation Mode: UHF
Frequency Response: 50Hz-15KHz(±3 dB)
Dynamic Range: 110dB
S/N: 90dB
T.H.D: < 0.1%(1KHz)
Audio Output Jack: (Ch1/Ch2) XLR – 1/4″ balanced + 1/4″ mixed
Power Voltage: AC110V-240V 50/60Hz
Rechargeable Battery: 1.2V (can take up to 24 hours to fully recharge)
Operating Temperature: 23°F-104°F
Mic Battery Operating Time: up to 15 hours
Operating range is subject to environmental conditions. Results may vary.
Receiver (Front)
| a. Antenna | c. LED charge indicator | e. Radio frequency LED indicator |
|---|---|---|
| b. Power ON/OFF switch | d. Volume control knob | f. Audio frequency level LED |
indicator
Receiver (Back)
| a. Antenna port | c. Individual channel outputs | e. Individual mic outputs |
|---|---|---|
| b. Charging port | d. 2 channel mix output | f. Power input |
Microphones
| a. Microphone windscreen | c. Power ON/OFF switch |
|---|---|
| b. Low battery indicator | d. Battery compartment |
Receiver LCD Display
a. Channel frequency display| b. Group number display| c. Channel number
display
---|---|---
Remember to remove protective plastic film from the LCD display
Setup and Operation
- The receiver should be placed in an area that is stable and least likely to shake the unit.
- The receiver should be at least 3’ off the ground for optimal transmission.
- Connect the antenna, balanced cable AF line, and power supply provided.
- The antenna should extend vertically.
- Switch on the receiver.
- While the receiver is in stand-by, switch on the microphones.
- Adjust volume as necessary.
- Place the microphone base firmly on the charging port to recharge.
Tip: To minimize
feedback avoid operating the microphones in close proximity of or in front of
speakers.
Microphone Operation
Standby/ Mute Mode
Put the hand held microphone switch in the MIDDLE position.
The microphone power LED indicator will be on.
Now the mic is on standby and mute mode.
Active Mode
Put hand held microphone switch in the ON position.
The microphone power led indicator will be on.
Now the microphone is in active mode and is ready for use.
The receiver RF LED indicator will be on.
Battery Status
As the microphone battery power diminishes, the power LED indicator will
gradually become darker until it finally turns off.
At this point you need to recharge or change the batteries.
Charging the Microphones
Turn off the power before charging.
Place the microphone in the charging port as shown.
The initial charge will take longer than subsequent recharges. Please allow it
to charge overnight.
The charge LED indicator on the receiver will turn off when the microphone is
fully charged.
Troubleshooting
| Problem | Solution |
|---|---|
| No sound or faint sound | • Verify all sound system connections or adjust |
channel volume as needed.
• Verify that the receiver is connected to the mixer/ amplifier.
• Turn on transmitter.
• Make sure the batteries are installed correctly.
• Charge or change battery.
• Make sure AC adapter is securely plugged into electrical outlet.
• Make sure receiver is powered on.
Audio artifacts or dropouts| • Change receiver and transmitter to a different
group and/or channel.
• Identify nearby sources of interference (cell phones, Wi-Fi access points,
signal processor, etc…) and shutdown or remove source.
• Charge or change transmitter battery.
• System must be set up within recommended range and receiver kept away from
metallic surfaces.
• Transmitter must be used in line of sight from receiver for optimal sound.
Distortion| Reduce transmitter channel volume.
Sound level variations when switching to different sources| Adjust transmitter
volume as necessary.
Transmitter information does not appear on the Receiver LCD| Transmitter is
off.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Responsible party name: Rockville
Address: 600 Bayview Ave,
Entrance A,
Inwood, NY 11096
Hereby declares that the product Rockville RWM2603UR wireless microphone system complies with FCC rules as mentioned in the following paragraph:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
tuming the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Visit us at:
RockvilleAudio.com
Due to constant improvements, these specifications are subject to change
without notice.
Copyright 2020
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>