KLEIN Bluetooth Jobsite Speaker AEPJS-1 Instructions

: June 6, 2024
: KLEIN

AEPJS-1

Bluetooth® Jobsite Speaker – Instructions

KLEIN Bluetooth Jobsite Speaker AEPJS-1

FIG. A

FRONT

KLEIN Bluetooth Jobsite Speaker AEPJS-1 - FRONT

BACK

KLEIN Bluetooth Jobsite Speaker AEPJS-1 - BACK

BOTTOM

KLEIN Bluetooth Jobsite Speaker AEPJS-1 - BOTTOM

1390176 Rev 06/20 F

Klein Tools AEPJS-1 is a powered speaker designed to provide high-quality sound for smart phones, tablets, computers or other audio devices.

GENERAL SPECIFICATIONS

Dimensions: 3.88″ x 3.5″ x 2.13″ (98.6 x 88.9 x 54.1 mm)
Weight: 10 oz. (283 g)
Wireless Compatibility: Devices with Bluetooth® Version 4.2
Wireless Connection Range: 32.8 ft. (10 m) in open space
Support Profiles: A2DP, AVRCP, GAVDP, HFP
Output Power: 5W
Battery Type: Internal, Li-Ion, 3.7V / 2150mAh
Battery Life: Approx. 10 to 13 hours at 70% volume
Charging Requirements: Maximum 5V DC, Minimum 0.4A
Certifications: CE, FCC, IC, & BC
Operating/Charging Temperature: 32° to 104°F (0° to 40°C)
Storage Temperature: -22° to 140°F (-30° to 60°C)
Relative Humidity: <85% non-condensing
Drop Protection: 6.6 ft. (2 m)
Ingress Protection (IP) Rating: IP45

IP Rating 1st number (IP45): Protected against solid objects over 1 mm in diameter

IP Rating 2nd number (IP45): Protected against low-pressure jets of water from all directions

Specifications subject to change.

WARNINGS

Read, understand, and follow these instructions to ensure safe operation.
Failure to observe these warnings can result in risk of fire or electric shock.

Keep these instructions for future reference.
No user-servicable parts inside. Do not open enclosure or attempt to repair this speaker.
Never lubricate any part of this speaker.
Never place this speaker on other electrical equipment.
Do not expose to direct sunlight, open flame, heat sources, equipment that produces heat, or extremes in environmental temperature.
Never immerse in water or other liquids. Avoid spilling liquids or falling foreign objects into openings or vents on the speaker enclosure.
Water-resistant cover must be properly sealed to achieve specified water & foreigh object ingress protection. Keep seal free of dirt, oil, sand, or other material that interferes with proper sealing. Failure to do so can result in risk of fire or electric shock.
Do not open water-resistant cover if wet or in a wet environment. Dry the speaker thoroughly and the seal around water-resistant cover completely before opening water-resistant cover.
When speaker is in use or charging, make sure there is adequate space to allow ventilation of internally-generated heat.
Use safety-rated power supply or wall adapter. Never use power supply or wall adapter that exceeds the specified charging voltage and current.
Route the power supply cable so that it will not to be stepped on or pinched by other objects.

SYMBOLS ON PRODUCT

****	Warning or Caution
Risk of Electrical Shock
Conformité Européenne. Conforms with European Economic Area directives.
WEEE – battery disposal
FCC. Conforms with particular Code of Federal regulations.
Meets CEC and DOE energy efficiency requirements.

FEATURE DETAILS (FIG.A)

1 Power button
2 “-” Volume down/skip backward button
3 Play/Pause/Talk button
4 “+” Volume up/skip forward button
5 USB charging port
6 Auxiliary “Aux In” jack
7 Water-resistant cover
8 LED indicator
9 Microphone
10 Lanyard tie point
11 1/4-20 mount
12 Magnet
13 Tool bag mounting flange

MAINTENANCE

CLEANING: Be sure speaker is turned off and wipe with a clean, dry lint- free cloth. Do not use abrasive cleaners or solvents.

STORAGE: If the speaker is to be left unused for an extended period of time, charge before storing, and recharge periodically during storage, to maintain battery’s charging capacity.

OPERATING INSTRUCTIONS

CHARGING BATTERY
** Fully charge speaker before use. First-time charge should be at least 4 hours.
Connect micro USB cable connection to USB charging port 5** , plug the other end of cable to computer or USB AC adapter or other USB power supply (not included). USB adapter/power supply should not exceed the specified charging voltage and current (Max. 5V DC, min. 0.4A). Normal charging time is 4 – 6 hours.

LED Indicator Color	Status
Solid Red	Battery charging (LED off when fully charged)
Flashing Red	Low battery
Solid Blue	Active Bluetooth® wireless connection
Slow-Flashing Blue	Attempting to pair with wireless device
Quick-Flashing Blue	Attempting to auto-link to paired wireless device
Solid Green	Aux line-in connection (overrides wireless connection)
No LED	Unit is off, battery is dead, or battery has finished charging

NOTE: LED may appear purple or yellow if battery is low or is charging.

ON/OFF: Press & hold power button 1 for 3 seconds, a tone will sound. Unit will automatically power off after 10 minutes of inactivity.

NOTE: Turn unit off when not in use to prolong battery life.

PAIRING: Wireless connection activates automatically and is ready to pair when unit is turned on. On your Bluetooth® wireless compatible device, enable Bluetooth® and search/scan for devices that can be paired. Select “AEPJS1” when it appears (refer to the user manual of your device). If necessary, enter “0000” as pairing passcode. A tone sounds after a successful pairing.

NOTE: Unit automatically attempts to connect the last wireless device but is ready to pair with any compatible device if the last paired device is not detected within 5 seconds of powering on.

DISCONNECT PAIRING: 1) Turn unit off; -or- 2) Double-press Power Button 1 (tone sounds); -or- 3) Plug a cable into Aux jack 6 ; -or- 4) turn off Bluetooth® wireless connection in paired device.

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations.
Please see www.epa.gov or www.erecycle.org for additional information.

OPERATING INSTRUCTIONS

PLEASE SEE REVERSE SIDE.

CUSTOMER SERVICE

KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069
1-800-553-4676

customerservice@kleintools.com
www.kleintools.com

*The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Klein Tools, Inc. is under license.

RESET WIRELESS CONNECTION OR PAIRING WITH DIFFERENT DEVICES: Double-press Power Button 1 (tone sounds). Repeat Pairing procedure with different devices.

PLAYING AUDIO: Use your device to control the speaker or use the built-in control buttons on the speaker.

Press Play/Pause/Talk button 3 to play or pause audio on your device.
Short-press the “-” 2 or “+” 4 button to adjust the speaker volume. A tone will sound when maximum volume is reached. Volume may also be controlled from your audio device.
Long press the “-” 2 or “+” 4 button to skip backward or forward (respectively) during a song.

AUXILIARY AUDIO-IN: Connect one end of the auxiliary cable to the AUX jack 6 of the speaker, plug the other end of cable to line-out or headphone jack of your device.

SPEAKERPHONE OPERATION:

When an incoming call occurs, playing music is muted & ring tone sounds. Short-press Play/Pause/Talk button 3 to answer the call, or long-press to ignore.
To disconnect the call, short press the Play/Pause/Talk button 3 to hang up.
To redial last call, long press Play/Pause/Talk button 3 when speaker is playing music.

LOW BATTERY INDICATION: A continuous double-beep tone will sound when battery level drops to approximately 10%. Speaker will automatically power off when the battery level is below 3%. Recharge speaker as soon as possible.

POSITIONING SPEAKER:

Make sure that front of speaker is not obstructed.
Stand speaker upright on a flat, level, stable surface.
Attach speaker to a metal surface via the magnet on the back of the unit 12. DO NOT mount to electrical equipment.
Mount speaker to any tripod or stand that uses a standard 1/4-20 threaded mounting screw, via the 1/4-20 mount 11 on the bottom of the unit.
Mount speaker to the Klein Tools Lighted Tool Bag, Cat. No. 55431. To attach speaker to tool bag, first remove worklight from bag by rotating counter-clockwise. Align tabs on mounting flange 13 on the back of the speaker with mounting hole on bag and rotate clockwise to secure in place.

COMPLIANCE

FCC & IC COMPLIANCE

This device complies with part 15 of the FCC RULES and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.

NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

FCC RF EXPOSURE STATEMENTS:

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body or nearby persons.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

IC NOTICE TO CANADIAN USERS

This device complies with industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 5 mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.

IFETEL REPORT

For use in Mexico, the operation of this equipment is subject to the following two conditions: (1) This equipment or device does not cause harmful interference and (2) this equipment or device accepts any interference, including that which can cause undesired operation.