HUAWEI GT2 Wireless Charger Watch User Guide

: June 6, 2024
: Huawei

Table of Contents

Charging a HUAWEI WATCH
Safety Information
- Precautions
- Disposal and Recycling Information
Reduction of Hazardous Substances
EU Regulatory Conformance Body Worn Operation
Statement
Frequency Bands and Power
Accessories and Software Information
FCC Statement
IC Statement
Industry Canada compliance RF exposure requirements
Legal Statement
- Privacy Protection
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

HUAWEI GT2 Wireless Charger Watch

Charging a HUAWEI WATCH

Connect a charging adapter to the socket.
Connect the HUAWEI WATCH wireless charger (charger for short)
to the adapter.
Place the rechargeable area of your watch onto the center surface of the charger. Charging will begin on contact. (To locate the rechargeable area of your watch, please refer to the user manual of the watch.)
Note: The charging adapter must be purchased separately.

Safety Information

Before using the charger, read the following precautions:

In places where the use of wireless devices is prohibited, comply with the regulations and do not use your charger.
The charger contains a magnet, which may affect normal operation of implantable medical devices or personal medical devices, such as pacemakers, cochlear implants, and hearing aids. Consult the manufacturer of your medical devices for more information. When using the charger, keep it at least 30 cm away from implantable medical devices.
Keep the charger dry. Avoid using it in dusty, damp, or dirty environments, as such environments may cause charger malfunction. Do not splash water on the charger. Keep the charger away from fire and do not ignite it.
Do not use the charger during thunderstorms, as thunderstorms may cause charger malfunction or a shock hazard.
Only use the charger within its approved operating range of 10°C to +45°C, and only allow it to be exposed to temperatures within its approved storage range of 40°C to +70°C. Extreme heat or cold may cause charger malfunction.
If the charging adapter needs to be replaced, the output of the adapter must match the specifications of the charger, and must comply with IEC/EN 62368-1 “Audio/video, information and communication equipment Part 1: Safety requirements” and IEC/EN 60950-1 “Information technology equipment Safety Part 1: General requirements.”
If the charger needs to be connected to a USB port, ensure that the USB port is USB-IF certified, and that it complies with USB-IF standards.
Do not expose the charger to heat sources such as direct sunlight, warmers, microwave ovens, ovens, or water heaters.
Dispose of the charger in accordance with local regulations. Do not dispose of it as normal household waste. Comply with local laws on the disposal of the charger and its accessories and support recycling efforts.
Prevent accidental swallowing of the charger by children and pets.
Keep the charger out of the reach of children.
Do not drop, squeeze, or pierce the charger as this may cause charger malfunction.
Connecting the charger to a non-approved or incompatible power supply, charging adapter, or meter may cause hazards such as fire.
Do not place metallic items onto the surface of the charger for a long time, as they may induce heat and cause charger malfunction.

Precautions

If your watch is not correctly placed, it may not charge properly.
Do not place any object between your watch and the charger.

Disposal and Recycling Information

The crossed-out wheeled-bin symbol on your product, battery, literature or packaging reminds you that all electronic products and batteries must be taken to separate waste collection points at the end of their working lives; they must not be disposed of in the normal waste stream with household garbage. It is the responsibility of the user to dispose of the device using a designated collection point or service for separate recycling of waste electrical and electronic equipment (WEEE) and batteries according to local laws. Proper collection and recycling of your device helps ensure electrical and electronic equipment (EEE) waste is recycled in a manner that conserves valuable materials and protects human health and the environment, improper handling, accidental breakage, damage, and/or improper recycling at the end of its life may be harmful for health and environment. For more information about where and how to drop off your EEE waste, contact your local authorities, retailer or household waste disposal service or visit the website https://consumer.huawei.com/en/.

Reduction of Hazardous Substances

This device and any electrical accessories are compliant with local applicable rules on the restriction of the use of certain hazardous substances in electrical and electronic equipment, such as the EU
REACH Regulation, RoHS Directive, and Battery Directive, etc. For declarations of conformity about REACH and RoHS, visit the website http://consumer.huawei.com/certification.

EU Regulatory Conformance Body Worn Operation

This device has been tested and meets applicable limits for radio frequency (RF) exposure. Exposure max value is 2.3959V/m at 10 cm distance.

Statement

Hereby, Huawei declares that this device CP81-1 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
The most recent and valid version of the Declaration of Conformity (DoC) can be viewed at http://consumer.huawei.com/certification.
This device may be operated in all member states of the EU. Observe national and local regulations where the device is used. This device may be restricted for use, depending on the local network.

Frequency Bands and Power

(a) Frequency bands 110.5–148 kHz.
(b) Maximum radio-frequency power transmitted in the
frequency bands in which the radio equipment operates: The maximum power for all bands is less than the highest limit value specified in the related Harmonized Standard.
The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to this radio equipment are as follows: 22.27 dBμA/m at 3 m

Accessories and Software Information

The product software version is 88.6E.01.05. Software updates may be released by the manufacturer to fix bugs or enhance functions after the product has been released. All software versions released by the manufacturer have been verified and are still compliant with the related rules.
All RF parameters (for example, frequency range and output power) are not accessible to the user, and cannot be changed by the user. For the most recent information about accessories and software, see the DoC at http://consumer.huawei.com/certification.

FCC Statement

When the device is running, keep a minimum distance of 15 cm away from it. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,M may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications to this device not expressly approved by Huawei for compliance could void the user’s authority to operate the device

IC Statement

This device complies with CAN ICES-3 (B)/NMB-3 (B).
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada compliance RF exposure requirements

This equipment complies with relevant RF radiation exposure limits set forth for a public/uncontrolled environment. This equipment should be installed and/or operated with a minimum distance as below between the radiator and your body: 10 centimeters.

Legal Statement

Copyright © Huawei 2021, All rights reserved
This document is for reference only. Nothing in this guide constitutes a warranty of any kind, express or implied.
All pictures and illustrations in this guide, including but not limited to the product color, size, and display content, are for your reference only. The actual product may vary. Nothing in this guide constitutes a warranty of any kind, express or implied. Visit http://consumer.huawei.com/us/support/index.htm for recent updated hotline and email address in your country or region.