MONSTER MLB7-1046-RGB Multi-Color/Multi White LED Light Bulb with IR Remote Control User Manual

MONSTER MLB7-1046-RGB Multi-Color/Multi White LED Light Bulb with IR

Remote Control

Introduction

This Multi-color/Multi-white LED Light Bulb is easy to install, easy to use, and is ideal for adding controllable ambient lighting to any room.

Features

• Multi-color and dimmable LED lighting effects
• Included color-selector remote works up to 26ft away
• E26/A21 shape conveniently fits into most standard fixtures
• Plug and play

What’s Included

• Multi-color/Multi-white LED Light Bulb
• IR Remote Control with battery (1 x 3V battery, CR2025)
• User Manual x1 pc

Safety Instructions

Please read and understand all instructions before using this product. If damage is caused by failure to follow the instructions, this warranty is null and void.

• Keep these instructions.
• Do not use this product for emergency lighting/exits
• Not for use with dimmers
• Not for use in totally enclosed luminaires
• Risk of electrical shock – use in dry location only
• Do not expose this product to open flames or use near fire
• Do not drop, puncture, or disassemble this product.
• Do not use the product in a strong magnetic field.
• Use a clean, soft cloth to clean. Do not use any corrosive cleaners/oils to clean.
• Do not attempt to repair the device or open the unit as this will void the warranty.

Get Started

1. Turn off the light fixture and carefully remove the old bulb.
   CAUTION: If the fixture had been on, the bulb maybe hot.

2. Install the LED Light Bulb into the light socket.

3. Remove the tab from the battery compartment of the remote control.

4. Turn on the light fixture. Your LED Bulb is now ready to use.

Lighting Facts

• Brightness – 800 lumens

• Estimated Yearly Energy Cost – $0.70
  Based on 3 hours/day, 11¢/kWh. Cost depends on rates and use.

• Life – 22.8 years
  Based on 3 hrs/day

• White Appearance – WARM = 3000K ~ COOL = 5000K

• Energy Used – 5.8 Watts

• Bulb Shape – A21

• Bulb Screw – E26

Controls, at a Glance

1

| ON/OFF| Turn the product on and off
---|---|---

2

| MULTI-WHITE SELECTORS| Select from cool, soft, or warm white

3

| MULTI-COLOR SELECTORS| Change the color to match your mood

4

| FLASH| Flash color-changing mode

5

| STROBE| Strobe color-changing mode

6

| FADE| Fade color-changing mode

7

| SMOOTH| Smooth color-changing mode

8

| RESET| Reset to default settings

9

| DIMMER BUTTONS| Adjust the brightness/intensity

IR Remote Operation

1. Turn on the LED Light by pushing the ON button on the remote control
2. Select the desired color of the desired effect by pushing the corresponding button on the remote control
3. Set the desired brightness using the buttons to increase/decrease the intensity of color
4. Push the OFF button to turn off the LED Light

NOTE 1: In order to use the remote control, power to the light fixture must be on.
NOTE 2: You can still control your light fixture by an associated light switch, the LED Bulb will turn on again into the last used color or mode.

Changing the Remote Control Battery

The battery for the remote control has already been installed. Remove the battery pull tab to operate.

1. The battery compartment is located on the narrow side of the remote control
2. Remove the empty battery and insert a 3V battery, type CR2025, with the positive terminal pointing upwards
3. Place the battery compartment back in the remote control so it locks in place

Customer Service

1 Year Limited Warranty
Tel: 866-246-2008
Email: customerservice@monsterilluminessence.com

In the event this product becomes defective, please do not return this product to your retailer.

Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s warranty or authority to operate the equipment.

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed or mobile condition. The minimum separation distance is 20cm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>