ROCKVILLE RWM2602UR High Performance Hand Held Wireless Dual Microphone System Owner’s Manual
- June 6, 2024
- RockVille
Table of Contents
RWM2602UR
High-Performance Hand-Held Wireless Dual Microphone System
OWNER’S MANUAL
Thank you for purchasing this Rockville high-performance hand-held wireless
dual microphone system.
With the RWM2602UR we are happy to bring you what we consider to be the
absolute best value in pro audio microphone systems. Proudly conceived and
developed in the USA, Rockville pro audio products are designed and engineered
by a team of pro audio enthusiasts.
We have spared no expense in manufacturing these Wireless Microphones Units to
meet the highest quality standards. With proper care and installation, these
units will provide you with the highest levels of quality. We hope that these
units will bring you years of performance and reliability.
Please read this owner’s manual carefully for proper use of your Rockville
Wireless Microphone System. Should you need technical assistance please call
our technical helpline at
1-646-758-0144, Monday through Friday,
9 am to 5 pm EST.
Specs
FEATURES
- The high-performance wireless handheld rechargeable microphone system
- Built-in charging dock for microphones
- LED microphone charging LED indicator
- Includes RWM2602UR transmitter with (2) rechargeable handheld,
- High sensitivity, unidirectional, wireless cardioid microphones with rechargeable batteries
- Professional rack mount design with LCD displays
- Featuring a dual filter design to limit feedback and interference
- Individual microphone volume control
- Comfortable ergonomic composite microphone construction
- Low power consumption for longer battery life
- AF/RF LED Indicators
- Ultra signal stability minimizes audio artifacts
- OSA technology: Locates, prioritizes and selects the clearest frequency for the best sound quality
SPECIFICATIONS
- Operating Range*: 200´-260´(indoor), 160´-220´(outdoor)
- Frequency Range: 500MHz-600MHz
- Frequency Stability: ±0.005%
- Modulation Mode: UHF
- Frequency Response: 50Hz-15KHz(±3 dB)
- Dynamic Range: 110dB S/N: 90dB T.H.D: < 0.1%(1KHz)
- Audio Output Jack: (Ch1/Ch2) XLR – 1/4˝ balanced + 1/4˝ mixed
- Power Voltage: AC110V-240V 50/60Hz
- Rechargeable Battery: 1.2V (can take up to 24 hours to fully recharge)
- Operating Temperature: 23°F-104°F
- Mic Battery Operating Time: up to 15 hours
***** Operating range is subject to environmental conditions. Results may vary.
Receiver (Front)
a. Antenna
b. Power ON/OFF switch
c. LED charge indicator| d. Volume control knob
e. Radiofrequency LED indicator
f. Audio frequency level LED indicator
---|---
Receiver (Back)
a. Antenna port
b. Charging port
c. Individual channel outputs| d. 2 channel mix output
e. Individual mic outputs
f. Power input
---|---
Microphones
a. Microphone windscreen
b. Low battery indicator| c. Power ON/OFF switch
d. Battery compartment
---|---
Receiver LCD Display
a. Channel frequency display
b. Group number display
c. Channel number display
Remember to remove the protective plastic film from the LCD display
Setup and Operation
- The receiver should be placed in an area that is stable and least likely to shake the unit.
- The receiver should be at least 3´ off the ground for optimal transmission.
- Connect the antenna, balanced cable AF line, and power supply provided.
- The antenna should extend vertically.
- Switch on the receiver.
- While the receiver is on standby, switch on the microphones.
- Adjust volume as necessary.
- Place the microphone base firmly on the charging port to recharge.
Tip:
To minimize feedback avoid operating the microphones in close proximity of or
in front of speakers.
Microphone Operation
Standby/ Mute Mode
Put the handheld microphone switch in the MIDDLE position.
The microphone power LED indicator will be on.
Now the mic is on standby and mute mode.
Active Mode
Put handheld microphone switch in the ON position.
The microphone power led indicator will be on.
Now the microphone is in active mode and is ready for use.
The receiver RF LED indicator will be on.
Battery Status
As the microphone battery power diminishes, the power LED indicator will
gradually become darker until it finally turns off.
At this point, you need to recharge or change the batteries.
Charging the Microphones
Turn off the power before charging.
Place the microphone in the charging port as shown.
The initial charge will take longer than subsequent recharges. Please allow it
to charge overnight.
The charge LED indicator on the receiver will turn off when the microphone is
fully charged.
Troubleshooting
Problem
|
Solution
---|---
No sound or a faint sound|
-
Verify all sound system connections or adjust channel volume as needed.
-
Verify that the receiver is connected to the mixer/ amplifier.
-
Turn on the transmitter.
-
Make sure the batteries are installed correctly.
-
Charge or change battery.
-
Make sure the AC adapter is securely plugged into an electrical outlet.
-
Make sure the receiver is powered on.
Audio artifacts or dropouts|
- Change receiver and transmitter to a different group and/or channel.
- Identify nearby sources of interference (cell phones. Wi-Fi access points. signal processor. etc…) and shut down or remove the source.
- Charge or change transmitter battery.
- System must be set up within recommended range and the receiver kept away from metallic surfaces.
- The transmitter must be used in one of sight from the receiver for optimal sound.
Distortion| Reduce transmitter channel volume.
Sound level variations when switching to different sources| Adjust
transmitter volume as necessary.
Transmitter information does not appear on the Receiver LCD| The transmitter
is off.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Responsible party name: Rockville
Address: 600 Bayview Ave, Entrance A, Inwood, NY 11096
Hereby declares that the product Rockville RWM2602UR wireless microphone
system complies with FCC rules as mentioned in the following paragraph:
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device
must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Visit us at:
RockvillePro.com
Due to constant improvements, these specifications are subject to change
without notice.
Copyright 2016
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>