ROCKVILLE TM Series Home Theater System Tower Speaker Owner’s Manual

OWNER’S MANUAL

TM SERIES
COMPLETE POWERED HOME THEATER SPEAKER SYSTEM

https://vimeo.com/450192011

Who reads manuals? Instead, go to vimeo.com/473203709 or scan the QR code and watch a short video, which shows you how to set this item up and how to use it.

Thank you for purchasing this Rockville TM series complete powered home theater tower speaker system.

This powered home theater tower speaker system creates a new performance level in home theater speakers. Our unique design eliminates high-frequency diffraction while pro­viding full-range accuracy and enhanced bass response.

In the old days, a home theater system consisted of many speakers, a subwoofer, a re­ceiver, an equalizer, wires all over the place, a separate radio module, and lots of other devices. With the Rockville TM series home theater system, you will not need to purchase anything else. This has everything built-in! Each tower speaker has a tweeter, full-range speakers, and a subwoofer built-in. You can connect it to any TV easily through the RCA inputs or through the optical input. You can listen to all your music through your phone or MP3 player using Bluetooth or the 3.5mm aux input. We have equipped them with two 1/4″ mic inputs with echo and mic volume control so you can use these for karaoke. These also have USB and SD inputs as well as an FM radio receiver.

Please read this installation guide carefully for proper use of your Rockville TM series home theater speaker system. Should you need technical assistance, please call our technical helpline at 1-646-758-0144, Monday through Friday, 9 am to 5 pm EST.

Included

• (2) 10″ speakers (master & slave)
• (1) Proprietary noise rejecting speaker interconnect cable
• (1) Antenna cable
• Wireless remote control
• Plastic/rubber feet
• Manual
• Warranty card

IMPORTANT SAFETY INSTRUCTIONS

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE THE AMPLIFIER PLATE. NO USER-SERVICEABLE PARTS INSIDE. WE RECOMMEND TAKING THE UNIT TO A QUALIFIED SERVICE TECHNICIAN FOR ANY REPAIRS.

• Do not place these speakers on an unstable surface. The speaker may fall over, causing serious injury to a child or adult and serious damage to the unit.
• Do not use these speakers near water; for example, near a bathtub, sink, in a wet basement, or near a swimming pool.
• The speakers should be situated away from heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
• These speakers should be connected to a power supply outlet of the same voltage as that which is specified on the amp plate of the unit. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the unit.
• Clean only with a soft damp cloth. Unplug this product from the wall outlet before cleaning.
• Upon completion of any servicing or repairs, request that the service center/shop uses factory autho­rized replacement parts. Replacement with unauthorized parts may result in fire, electrical shock, or other hazards.

How to Avoid Irritating Feedback

The placement of your microphone is critical in avoiding feedback through your speaker. Never set up your microphone in front of the speaker. Always set up your microphone behind the speaker. When approaching the speaker to make any adjustments, we recom­mend approaching the speaker from the rear and not walking directly towards the front of the speaker.

FRONT PANEL (MASTER UNIT)

1. Volume +
2. Previous track/channel
3. Next track/channel
4. Power/standby
5. Input select
6. Play/pause/automatic station search (FM radio)
7. Volume –
8. SD card input
9. USB input
10. Mic 1 input
11. Mic 2 input

|
---|---

REAR PANEL (MASTER UNIT)

1. L/R RCA input 2
2. L/R RCA input 1
3. 5mm AUX input
4. Coaxial input
5. Optical input
6. FM antenna
7. L/R RCA output
8. Power switch
9. Output to left speaker
10. Power input

|
---|---

REMOTE CONTROL FUNCTIONS

**: Power/Standby
MUTE: Cancel unit sound
OPT/COAX: Select optical or coaxial input
SD/USB: Select SD or USB input
BT: Enter Bluetooth mode
FM: Enter FM radio mode
AUX1 /2/PC: Select RCA1, RCA2, or AUX input
CH +/-: Use to navigate FM stations
:** Previous track/next track
: Play/Pause in USB/SD/BT modes
AUTO: Automatic station search
SAVE: Save stations to unit memory
TUNE +/-: Manually tune FM stations
SW +/-: Subwoofer volume level
THE +/-: Adjust treble level
VOL +/-: Master volume control
EQ +/-: Select from preset EQ settings
DISP +/-: Adjust display brightness
0 — 9: Number pad used to direct select tracks when in USB/SD mode
REPEAT: Repeat one song/repeat all songs/shuffle
MIC +/-: Adjust the microphone volume
ECHO +/-: Adjust reverb volume|
---|---

SET UP

Place speakers in the desired position. Using the included proprietary noise rejecting cable, connect the master speaker to the slave unit. Now plug the master unit into the nearest AC outlet.

BLUETOOTH

To connect your iPod, iPhone, MP3 player, Android phone, or any other Bluetooth-capable device, follow the steps listed below.

1. Make sure the unit is plugged in and the power switch is in the ON position.
2. Press the BT button on the remote control or push the INPUT button on the unit until the digital readout shows “BT” and the blue indicator LED is on.
3. Turn on the Bluetooth feature on your device and ensure that it is in “discoverable” Search for “RockvilleTMxx” on your list of available devices and select it.
4. Listen for the voice prompt, “Bluetooth link” which indicates the devices are successfully paired.

USB/SD

For USB/SD playback follow the steps listed below.

1. Make sure the unit is plugged in and the power switch is in the ON position.
2. Press the USB/SD button on the remote control or push the INPUT button on the unit until the digital readout shows “USB” or “SD”.
3. Plugin your SD card or USB flash drive. The unit will automatically read the files and begin playing music.

RCA

For playback via RCA inputs follow the steps listed below.

1. Make sure the unit is plugged in and the power switch is in the ON position.
2. Press the AUX1/2/PC button on the remote control or push the INPUT button on the unit until the digital readout shows “AU1” or “AU2”.
3. If multiple sources are connected, use the remote button or INPUT button to switch between the sources.

These inputs labeled RCA 1 and RCA 2, can be used to connect stereo signal sources such as TVs, digital set-top boxes, game consoles, DVD players, CD players, etc.

AUXILIARY

Use the 3.5mm Auxiliary jack to connect computers, cellphones, or any other external sound source with a 3.5mm output.

1. Make sure the unit is plugged in and the power switch is in the ON position.
2. Press the AUX1/2/PC button on the remote control or push the INPUT button on the unit until the digital readout shows “PC”.

OPTICAUCOAXIAL

Many TVs, Digital set-top boxes, game consoles, and DVD players have optical (fiber op-tics) or coaxial outputs. To connect via Optical or Coaxial input, follow the steps listed below.

1. Make sure the unit is plugged in and the power switch is in the ON position.
2. Press the OPT/COAX button on the remote control or push the INPUT button on the unit until the digital readout shows “OPT” or “COAX”.
3. Use a digital optical audio cable to connect the speakers to the source.

OPTICAUCOAXIAL (CONTINUED)

4. Set your N’s sound output to external speakers.

Please note: If you are having issues with sound output, go into your N’s audio settings and make sure to deactivate Dolby Pro-Logic, Dolby ATMOS, etc. and select PCM format.

FM RADIO

For FM radio follow the steps listed below.

1. Make sure the unit is plugged in and the power switch is in the ON position. Be sure to connect the included FM antenna.
2. Press the FM button on the remote control or push the INPUT button on the unit until the digital readout shows numbers (see image below).
3. While in FM mode, press the AUTO button to activate automatic station search. Use the CH+/- buttons to manually search through stations.

MIC INPUT

To use the system for karaoke, connect any microphone via either one of the 1/4″ inputs located on the front of the unit.

WORK 0M00

RCA OUTPUT Use these RCA outputs to connect an additional subwoofer or the second set of speakers.

Troubleshooting

ON position.
2. Check that the power cable is not damaged.
No sound/ distorted sound| 1. Check that all appropriate cables are plugged incorrectly.
2. Check the volume settings on the unit.
3. Check the volume settings on the input source.
4. Make sure you’ve selected external speakers in your N’s sound output settings.
5. Deactivate Dolby Pro-Logic, Dolby ATMOS, etc., and select PCM in your N’s sound format settings.
6.If using a microphone, make sure it is on.
7. Make sure the proper source is selected.
8. If the unit volume or source volume is maxed out, turn one of them down as you may be overdriving the unit.
Mic feedback| Point the mic away from the speaker. Make sure the mic is behind of the speaker, not in front of it.
Poor mic sound| Make sure you are using a proper cable. For’ ” cables, there are 3 types: instrument, TS (unbalanced), and TRS (balanced). Use TRS cables when connecting microphones to this unit.
Bluetooth pairing fails| 1. Check to see that both devices are turned on and that your Bluetooth device is discoverable.
2. Turn both devices off and then on again.
3. Make sure you’ve selected the proper source.
4. Make sure that the Bluetooth device is within 5 feet of the unit while pairing.
5. Move both devices away from other Bluetooth devices, microwaves, wireless routers, and other electronics.
6. Make sure that the unit is not paired to a previously paired device.
No SD or USB playback| 1. Make sure you’ve selected the proper source.
2. Make sure that the audio files are in the specified formats: MP3, WMA, WAV FLAG, APE, F1A, SBC, and MC.

FEATURES TM80

• Complete Powered Home Theater Tower Speaker System With Dual fr Subs
• Peak Power: 800 watts
• RMS Power: 200 watts
• (2) 8– subwoofers
• (4) Full-range drivers: 4′ full-range drivers with polypropylene cones, rubber surrounds, and bullet dust cap
• (2) silk dome tweeters
• Class “NB” amplifier circuitry with auto-switching power supply
• Built-in, 8 band equalizer with preset equalizer settings
• Adjustable bass and treble
• Computer-optimized electronic crossover network supplies amazing sounding highs, lows, and mids
• The digital display on the front panel with brightness control
• Built-in Bluetooth with 150-foot range and perfect interference-free sound quality
• Built-in USB playback (MP3, WMA, WAV, FLAG, APE, F1A, SBC, and MC)
• Built-in SD card playback (MP3, WMA, WAV, FLAC, APE, F1A, SBC, and MC)
• Built-in FM radio with crystal clear reception
• Full function remote included
• Front-panel USB/SD inputs
• Easily connect to your television through RCA or through the optical connection
• Ferrofluid enhanced 1– neodymium silk dome tweeter
• Tweeter has a 1–voice coil diameter
• Specially wound voice coils produce accurate responses along the entire frequency spectrum
• One complete pair with master/slave output connection
• Includes a noise rejecting cable to connect the 2 speakers together

SPECIFICATIONS

Amplifier: Class NB
Quad Amp Design: Each driver features frequency specific independent amplifiers
Low Frequency: (2) 8″ paper cone with sponge surround
Mid Frequency: (4) 4″ polypropylene cone with rubber surround
High Frequency: (2)1– neodymium silk dome tweeter
Frequency Response: 40Hz – 20kHz
SPL Peak: 106dB 01w/1m
S/N Ratio: >60dB
Separation: >45dB
Input Connectors: (2) unbalanced RCA, (2) balanced front panel 1/4″, (1) Optical, (1) 3.5mm, (1) USB 2.0, (1) SD
Output Connectors: (1) unbalanced RCA
AC Power Input: 120V (60Hz)
Dimensions (H x W x D): 31.9″ (810mm) x 6.3″ (160.02mm) x 12.99″ (330mm)
Weight (both speakers): 41.9Ibs (19kg)

FEATURES TM150

• Complete Powered Home Theater Tower Speaker System With Dual 10″ Subs
• Peak Power: 1000 watts
• RMS Power: 250 watts
• (2) 10″ subwoofers
• (6) Full-range drivers: 4″ full-range drivers with polypropylene cones, rubber surrounds, and bullet dust cap
• (2) silk dome tweeters
• Class “NB” amplifier circuitry with auto-switching power supply
• Built-in, 8 band equalizer with preset equalizer settings
• Adjustable bass and treble
• Computer-optimized electronic crossover network supplies amazing sounding highs, lows, and mids
• The digital display on the front panel with brightness control
• Built-in Bluetooth with 150-foot range and perfect interference-free sound quality
• Built-in USB playback (MP3, WMA, WAV, FLAC, APE, F1A, SBC, and MC)
• Built-in SD card playback (MP3, WMA, WAV, FLAG, APE, F1A, SBC, and MC)
• Built-in FM radio with crystal clear reception
• Full function remote included
• Front-panel USB/SD inputs
• Easily connect to your television through RCA or through the optical connection
• Ferrofluid enhanced 1″ neodymium silk dome tweeter
• Tweeter has a 1″ voice coil diameter
• Specially wound voice coils produce accurate responses along the entire frequency spectrum
• One complete pair with master/slave output connection
• Includes a noise rejecting cable to connect the 2 speakers together

SPECIFICATIONS

Amplifier: Class NB
Quad Amp Design: Each driver features frequency specific independent amplifiers
Low Frequency: (2) 10″ paper cone with sponge surround
Mid Frequency: (6) 4″ polypropylene cone with rubber surround
High Frequency: (2) 1″ neodymium silk dome tweeter
Frequency Response: 40Hz – 20kHz
SPL Peak: 110dB @I w/1m
S/N Ratio: >60dB
Separation: >45dB
Input Connectors: (2) unbalanced RCA, (2) balanced front panel 1/4″, (1) Optical, (1) 3.5mm, (1) USB 2.0, (1) SD
Output Connectors: (1) unbalanced RCA
AC Power Input: 120V (60Hz)
Dimensions (H x W x D): 37.4″ (950mm) x 6.3″ (160.02mm) x 12.99″ (330mm)
Weight (both speakers): 57.4lbs (26kg)

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible party name: Rockville
Address: 600 Bayview Ave, Entrance A, Inwood, NY 11096

Hereby declares that the product Rockville TM SERIES complete powered home theater tower speaker system complies with FCC rules as mentioned in the following paragraph:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable pro­tection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter­ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RockvilleAudio.com
© 2020 ROCKVILLE // Features and specifications are subject to change and or improvement without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>