DIGITUS 4K HDMI Extender Set over IP/CAT User Manual
- June 6, 2024
- DIGITUS
Table of Contents
DIGITUS 4K HDMI Extender Set over IP/CAT User Manual
Important Safety notice
Please read below safety instructions carefully before installation and operation:
- Please pay attention to all the warnings and hints on this device
- Do not expose this unit to rain, moisture and liquid
- Do not put any stuff into the device
- Do not repair or open this device without professional people’s guidance
- Shut off power and make sure environment is safe before installation Do not plug-in/out the network cables and IR cables when it isin using to avoid cables damage
- Please note that our extender supports 5V power supply also, but the
- Volt power port is alternative. Please do not connect PoE power supply and 5V powersupply at the same time, choose each one would work
Introduction
HDMI over IP extender, takes the advantages of the latest transmission technology, extends your HDMI video/audio with the resolution of 4Kx2K 30Hz up to 120m (394 feet) via single network cable. Supports IR signal transmission, to control media playback of the signal source device at the display location. Supports PoE.
Package Contents
Installation Requirements
- HDMI source device (computer graphics card, DVD, PS3, HD monitoring equipment etc.).
- HDMI display device like SDTV, HDTV, and projector with HDMI port.
- Network cables: CAT 5/5e/6 network cables
- Transmission length: CAT5 80m/CAT5E 100m/CAT6 120m
- PoE powered device:
Support and compliant with IEEE802.3af international standard
switcher and other PoE power supply devices. The maximal wattage
of the transmitter or receiver is 10w only.
Panel Description
1. HDMI EXTENDER TX (Sender)
2. HDMI EXTENDER RX (Receiver)
Installation Procedures
1. Connections
1.1. Point to Point connection: Up to 120 meters transmission distance over single CAT6 (High quality cable can reach 150 meters)
1.2. Router Connection: By using network router/repeater, realize unlimited extension.
1.3. One-to-many Connection: By using network router/switch, one
sender to several receivers, realize extender & splitter function.
Specification
FAQ
Q: TV display “Waiting for connection” on the right corner?
A: Please check if the power supply of TX (Sender) and switcher (if used) is
connected, and make sure connecting cable is firmly.
Q: TV display “Please check the TX input signal”?
A: Please check if there is a HDMI signal input of TX
Try to connect the signal source directly to display device to see if there is
signal output from source device or change the signal source, HDMI wire and
try again
Q: When playing 4Kx2K source, screen is back without any content?
A: Make sure both TV and HDMI cable support HDMI1.4.
Q: Display not fluent, not stable?
A: Please check the cable length between the TX to switch, the switch to the
RX and the connection between each level is within the required range.
Click the “Reset” button on the TX/RX front panel, reset and reconnect.
Disclaimer
The product name and brand name may be registered trademark of related manufacturers.TM and ® may be omitted on the user manual. The pictures on the user manual are just for reference, and there may be some slight difference with the real products. We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.
This is a Class A product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>