SW-MOTECH BC.HTA.11.928.20100 Legend Gear Side Bag Instruction Manual

mounting instructions
BC.HTA.11.928.20100
contains
HTA.11.928.10000, HTA.11.928.11000,
BC.HTA.00.402.10200L, BC.HTA.00.402.10200R
Revision: 01
Item No.: HTA.11.928.10000 & HTA.11.928.11000

Thank you for choosing this premium product from SW-MOTECH.
Please visit our web shop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webs hop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility
with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

Step| No.| Item No. Description| Part| Quantity| **Nm***
---|---|---|---|---|---
| | HTA.11.928.11000| SLC Side Carrier right**| |
1| 1| HTA.11.928.902.01| Side Carrier; right| 1|
2| HTA.00.152.080| Guide Bolt| 3|
3| HTA.00.152.081| Lock Bolt| 1| 8
4| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1| 2
5| M6 x 20; DIN 7991| Countersunk Screw; black| 2|
2| 6| M8 x 16; ISO 7380| Lenshead Screw; black| 2| 18
| | HTA.11.928.10000| SLC Side Carrier left| |
| | (1) HTA.11.928.901.01| Side Carrier; left| 1|
| | | Mounting parts see SLC Side Carrier right| |

8.8 and 10.9

• All measurements in millimeters.
  ** The second number indicates the total quantity of the part in the delivery.
  *** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

| |
---|---|---

MOUNTING

NOTE: The mounting steps [1] to [2] show the mounting of the right side carrier.
Mount the left side carrier in the same way as on the right side of the vehicle.

Attach the parts (2) to [5) to the side carrier (1), as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified.

Remove the seat bench from the vehicle.
Remove the original screw and washer from the suspension strut, as shown in the detail drawing.
Attach the side carrier (1) with the original screw and washer (Orig.) to the vehicle, as shown in the drawing.

ATTENTION: Use liquid thread locker!

Tighten the screws [6] as specified.
Tighten the original screw (Orig.) with the manufacturer’s specified torque.
Reattach the seat bench.

MOUNTING INSTRUCTIONS

Legend Gear Side Bag LC1 / LC2
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our web shop. >> www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no Liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration.

PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.

FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.

ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product! After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

LOADING INFORMATION

ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from moisture.
Additionally protect sensitive luggage (e.g., electronic equipment) from moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130 km/h!

PARTS LIST & CARE

CARE
Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from Salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong
cleaning agents, rough cleaning tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).
We recommend to impregnate the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjallraven).

ATTENTION: Because the textile surfaces material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!

ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions. SW- MOTECH assumes no liability for paint damage and abrasions.

FIXATION

Fasten the Velcro closure of the side bag [1a/1b).
Revert the reinforced opening of the side bag [1a/1b) twice completely.

Fix the shown loops with the side-mounted hook buckles.

Tighten the straps of the hook buckle.
Secure the opening of the side bag [1a/1b) with the shown strap.

Place the three openings of the quick release fastening system onto the locating bolts of the mounted SLC side carrier.

Press the side bag (1a/1b) slightly downward, until it properly rests on SLC side carrier.

ATTENTION: Make sure that all three locating bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism!

To release the side bag (1a/1b] simply press the shown slider of the locking mechanism downward.

SW-MOTECH GmbH & Co. KG
Ernteweg 8/10 – 35282 Rauschenberg – Germany
Phone + 49 (0)6425 / 8168 – 050
Fax + 49 (0)6425 / 8168 – 10
infofasw-motech.com : www.sw-motech.com

Copyright by
SW-MOTECH GmbH & Co. KG

Errors and omissions excepted. Technical and design modifications are subject to change.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>