OUTFORM T432S11 32 Inch Touch Display User Manual

June 5, 2024
Outform

T432S11 32 Inch Touch Display
User Manual

OUTFORM T432S11 32 Inch Touch Display

CAUTION

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS(Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion)
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.

Important Notices

Copyright Information

Copyright © 2018 Outform. All rights reserved.

All intellectual property rights in this publication are owned by Outform and protected by applicable copyright laws and international treaty provisions. Outform retains all rights not expressly granted. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Outform.

Outform reserves the right to revise this publication, and/or make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time without prior notice. The information in this document is provided in good faith, but without any representation or warranty whatsoever, whether it is accurate, complete, or otherwise, and on the express understanding that Outform shall have no liability whatsoever to other parties in any way arising from or relating to the information or its use.

All other trademarks are the property of their respective owners. Other company and brand products and service names are trademarks or registered trademarks of their respective holders.

This device complies with CE, and FCC regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Important Notices

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Safety and Warning Information

NOTE
This mark is applied to indicate that the equipment conforms to European safety and electromagnetic compatibility standards.

WARNING!
Main Supply: This equipment is designed to operate from a 100-240 Volt, 50/60Hz AC power supply. The use of other power sources may damage this equipment. Check that the voltage marked on the rating plate located at the rear of the power adaptor states 100-240V. The manufacturer will NOT accept responsibility for damage or injury caused by connecting to the wrong voltage.

WARNING!
Main Adaptor: The supplied power adaptor is compatible with a standard main socket.
If the power adaptor or lead gets damaged, it must be replaced by a qualified service agent with an approved adaptor of the same type and rating.

WARNING!
Dangerous voltage constituting a risk of electric shock is present inside this equipment.

WARNINGS!
The main plug shall be the main disconnect device and shall remain operable at all times.

Do not push objects into holes and ventilation slots.

Do not expose this product to moisture or place any objects filled with liquids on or near the product.

Do not place a naked flame source, such as lighted candles, on or near this product.

Do not store or operate the device in environments where the temperature is above 50 degrees celsius or below -10 degrees celsius.

Do not intentionally hit the device or place heavy or sharp objects on the device.

Only use accessories specified by the manufacturer.

Keep the device away from benzene, diluents, and other chemicals.

Do not attempt to repair this product yourself. Always use a qualified service agent to perform adjustments or repairs.

Package Contents

The package contains the following items:

OUTFORM T432S11 32 Inch Touch Display - Package
Contents

32’’ TOUCH DISPLAY Exterior Components

OUTFORM T432S11 32 Inch Touch Display - TOUCH DISPLAY Exterior
Components

No. Description
1 Camera
2 RJ45 Ethernet Port
3 TF-Card
4 SIM-Card Power button
5 USB Port
6 Recover button for FW upgrade
7 USB Port
8 Micro USB
9 HDMI-C
10 3.5 Audio
11 DC in Power Supply Port
12 Power button
13 Volume increase
14 Volume decrease
15 WiFi antenna
16 4G antenna

Setting Guide

Connecting keyboard

Step 1. Prepare a keyboard, connecting to the touch display.

OUTFORM T432S11 32 Inch Touch Display - Connecting
keyboard

Step 2. Press “Shift“ and then“F12“, and the screen will go to the setting page.

OUTFORM T432S11 32 Inch Touch Display - Connecting keyboard
2

Setting WiFi and Brightness and Sound etc.
Step 1. Click”System settings”.

OUTFORM T432S11 32 Inch Touch Display - System
settings

Step 2. Click” Network & Internet”.

OUTFORM T432S11 32 Inch Touch Display - Network &
Internet

Step 3. Turn on the “WiFi“ button.

OUTFORM T432S11 32 Inch Touch Display - WiFi

Step 4. Select the WiFi that you know the password then get connected.

OUTFORM T432S11 32 Inch Touch Display - WiFi 2

Step 5. When need to set brightness or wallpaper something, repeat Step 1~2, Select “Display“.

OUTFORM T432S11 32 Inch Touch Display - DisplayOUTFORM T432S11 32 Inch Touch Display - Display
2

Step 6. When need setting sound, repeat Step 1~2, Select “Sound“, you can adjust the Media volume, Alarm volume, Notification volume, or Advanced options.

OUTFORM T432S11 32 Inch Touch Display - volume or Advanced
optionsOUTFORM T432S11
32 Inch Touch Display - volume or Advanced options 2

For additional assistance, visit outformsupport.com.

OUTFORM All Rights Reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals