GARMIN G52QUWMEBX GPSMAP 7×2/9×2 Touch Series Chartplotter Instruction Manual
- June 6, 2024
- Garmin
Table of Contents
GPSMAP ® 7X2/9X2 PLUS
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
Failure to follow these warnings cautions, and notices could result in
personal injury, damage to the vessel or device, or poor product performance.
See the Important Safety and Product Information guide in the product box for
product warnings and other important information.
When connecting the power cable, do not remove the in-line fuse holder. To
prevent the possibility of injury or product damage caused by fire or
overheating, the appropriate fuse must be in place as indicated in the product
specifications. In addition, connecting the power cable without the
appropriate fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
To avoid possible personal injury or damage to the device and vessel, disconnect the vessel’s power supply before beginning to install the device.
To avoid possible personal injury or damage to the device or vessel, before applying power to the device, make sure that it has been properly grounded, following the instructions in the guide.
NOTICE
For the best possible performance, the device must be installed according to
these instructions.
When drilling or cutting, always check what is on the opposite side of the
surface to avoid damaging the vessel.
Read all installation instructions before proceeding with the installation. If
you experience difficulty during the installation, contact Garmin ® Product
Support.
Contacting Garmin Support
- Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support.
- In the USA, call 913-397-8200 or 1-800-800-1020.
- In the UK, call 0808 238 0000.
- In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the Chartplotter software after installation. For the
instructions on how to update the software, see the owner’s manual at
garmin.com/manuals/GPSMAP7x2-9x2Plus.
Tools Needed
- Drill
- Drill bits appropriate for the device and mounting style
| Mounting Style | Drill Bit Sizes |
|---|---|
| Bail with included M4 wood screws | 3.2 mm (1/8 in.) |
| Flush | 13 mm (1/2 in.) |
| Flush with included M3.5 wood screws (702 series) | 2 mm (5/84 in.) |
| Flush with included M4 wood screws (902 series) | 3.2 mm (1/8 in.) |
| Flush with included machine screws and nut plates | 6 mm (1/4 in.) 4 mm (3/18 |
in.)
Flush with included M3.5 machine screws and tapped holes (702 series)| M3.5
tap
Flush with included M4 machine screws and tapped holes (902 series)| M4 tap
-
2 Phillips screwdriver
- Jigsaw or rotary tool
- File and sandpaper
- Marine sealant (recommended)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed to extreme
temperatures or conditions. The temperature range for this device is listed in
the product specifications. Extended exposure to temperatures exceeding the
specified temperature range, in storage or operating conditions, may cause
device failure. Extreme-temperature-induced damage and related consequences
are not covered by the warranty.
When selecting a mounting location, you should observe these considerations.
- The location should provide optimal viewing as you operate your boat.
- The location should allow for easy access to all device interfaces, such as the keypad, touchscreen, and card reader, if applicable.
- The location must be strong enough to support the weight of the device and protect it from excessive vibration or shock.
- To avoid interference with a magnetic compass, the device should not be installed closer to a compass than the compass-safe distance value listed in the product specifications.
- The location must allow room for the routing and connection of all cables.
- The location must not be a flat, horizontal surface. The location should be in a vertical angle.
The location and viewing angle should be tested before you install the device. High viewing angles from above and below the display may result in a poor image.
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is recommended
to use a countersink bit to drill a clearance counterbore through only the top
gel-coat layer. This will help to avoid cracking in the gel-coat layer when
the screws are tightened.
You can use the included bracket to bail mount the device on a flat surface.
- Using the bail-mount bracket1 as a template, mark the pilot holes 2.
- Using a 3.2 mm ( 1 /8 in.) drill bit, drill the pilot holes.
- Secure the bail-mount bracket to the surface using the included M4 wood screws.
- Install the bail-mount knobs on the sides of the device.
- Place the device in the bail-mount bracket, and tighten the bail-mount knobs.
- Install the trim caps by snapping them in place around the edges of the device.
Flush Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and the mounting
holes, and cutting the hole too large could compromise the stability of the
device after it is mounted.
The included template and hardware can be used to flush mount the device in
your dashboard. There are three options for hardware based on the mounting
surface material.
- You can drill pilot holes and use the included wood screws.
- You can drill holes and use the included nut plates and machine screws. The nut plates can add stability to a thinner surface.
- You can punch and tap holes, and use the included machine screws.
-
Trim the template, and make sure it fits in the location where you want to mount the device.
-
Secure the template to the mounting location.
-
Using a 13 mm ( 1/2 in.) drill bit, drill one or more of the holes inside the corners of the solid line on the template to prepare the mounting surface for cutting.
-
Using a jigsaw or a rotary tool, cut the mounting surface along the inside line on the template.
-
Place the device in the cutout to test the fit.
-
If necessary, use a file and sandpaper to refine the size of the cutout.
-
If necessary, remove the trim caps.
NOTICE
Use a plastic pry tool when possible. Using a metal pry tool, such as a screwdriver, can damage the trim caps and the device. -
After the device fits correctly in the cutout, ensure the mounting holes on the device line up with the larger holes on the template.
-
If the mounting holes on the device do not line up, mark the new hole locations.
-
Based on your mounting surface and model, drill or punch and tap the larger holes:
• For the included wood screws on 702 models, drill 2 mm ( 5 /64 in.) holes and skip to step 18.
• For the included wood screws on 902 models, drill 3.2 mm ( 1/8 in.) holes and skip to step 18.
• For the included nut plate and machine screws, drill 6 mm ( 1/4 in.) holes in the larger hole locations.
• For the included machine screws without the nut plate on 702 models, punch and tap M3.5 holes, and skip to step 18.
• For the included machine screws without the nut plate on 902 models, punch and tap M4 holes, and skip to step 18. -
If you are using a nut plate, starting in one corner of the template, place a nut plate1 over the larger hole 2drilled in the previous step.
The smaller hole on the nut plate should line up with the smaller hole on the template. -
If the smaller hole on the nut plate does not line up with the smaller hole on the template, mark the new hole location.
-
If you are using a nut plate, drill a 4 mm (3 /16 in.) hole in the smaller hole location.
-
Repeat to verify the placement of the remaining nut plates and holes on the template.
-
Remove the template from the mounting surface.
-
Starting in one corner of the mounting location, place a nut plate on the back of the mounting surface, lining up the large and small holes.
The raised portion of the nut plate should fit into the larger hole.
-
Secure the nut plates to the mounting surface by fastening the smaller machine screws5 through the smaller holes.
-
Install the foam gasket 6 on the back of the device.
The pieces of the foam gasket have adhesive on the back. Make sure you remove the protective liner before installing them on the device. -
If you will not have access to the back of the device after you mount it, connect all necessary cables to the device before placing it into the cutout.
NOTICE
To prevent corrosion of the metal contacts, cover unused connectors with the attached weather caps. -
Apply marine sealant between the mounting surface and the device to properly seal and prevent leakage behind the dashboard.
-
If you will have access to the back of the device, apply marine sealant around the cutout.
-
Place the device into the cutout.
-
Secure the device to the mounting surface using the larger machine screws or the included wood screws.
-
Wipe away all excess marine sealant.
-
Install the trim caps by snapping them in place around the edges of the device.
Cable and Connection Considerations
- The cables may have been packaged without the locking rings installed. If so, you should route the cables before you install the locking rings.
- After connecting a locking ring to a cable, make sure the ring is securely connected and the O-ring is in place so the connection remains secure.
Connecting to Power
WARNING
When connecting the power cable, do not remove the in-line fuse holder. To
prevent the possibility of injury or product damage caused by fire or
overheating, the appropriate fuse must be in place as indicated in the product
specifications. In addition, connecting the power cable without the
appropriate fuse in place voids the product warranty.
You should connect the red wire to the same battery through the ignition or
another manual switch to turn the device on and off.
- Route the power cable between the power source and the device.
- Connect the red power wire to the ignition or another manual switch, and connect the switch to the positive (+) battery terminal if necessary.
- Connect the black wire to the negative (-) battery terminal or to the ground.
- Connect the power cable to the device, and turn the locking ring clockwise to tighten it.
Power/NMEA® 0183 Cable
- The wiring harness connects the device to power, NMEA 0183 devices, and a lamp or a horn for visible or audible alerts.
- If it is necessary to extend the NMEA 0183 or alarm wires, you must use 22 AWG (.33 mm²) wires.
- This cable provides one differential NMEA 0183 input and output port.
| Item | Wire Color | Wire Function |
|---|---|---|
| 1 | Red | Power |
| 2 | Black | Ground (power and NMEA 0183) |
| 3 | Blue | NMEA 0183 TxA (Out +) |
| 4 | Gray | NMEA 0183 TxB (Out -) |
| 5 | Brown | NMEA 0183 RxA (In +) |
| 6 | Violet | NMEA 0183 RxB (In -) |
| 7 | Orange | Accessory on |
| 8 | Yellow | Alarm low |
Additional Grounding Consideration
This device should not need additional chassis grounding in most installation situations. If you experience interference, you can use the grounding screw on the housing to connect the device to the water ground of the boat to help avoid the interference.
Garmin Marine Network Considerations
NOTICE
A Garmin Marine Network PoE Isolation Coupler (010-10580-10) must be used when
connecting any third-party device, such as a FLIR® camera, to a Garmin Marine
Network. Connecting a Power over Ethernet (PoE) device directly to a Garmin
Marine Network Chartplotter damages the Garmin Chartplotter and may damage the
PoE device. Connecting any third-party device directly to a Garmin Marine
Network Chartplotter will cause abnormal behavior on the Garmin devices,
including the devices not properly turning off or the software, becoming
inoperable.
This device can connect to additional Garmin Marine Network devices to share
data such as radar, sonar, and detailed mapping. When connecting Garmin Marine
Network devices to this device, observe these considerations.
-
All devices connected to the Garmin Marine Network must be connected to the same ground. If multiple power sources are used for Garmin Marine Network devices, you must tie all ground connections from all power supplies together using a low resistance connection or tie them to a common ground bus bar, if available.
-
A Garmin Marine Network cable must be used for all Garmin Marine Network connections.
◦ Third-party CAT5 cable and RJ45 connectors must not be used for Garmin Marine Network connections.
◦ Additional Garmin Marine Network cables and connectors are available from your Garmin dealer. -
The NETWORK ports on the device each act as a network switch. Any compatible device can be connected to any NETWORK port to share data with all devices on the boat connected by a Garmin Marine Network cable.
NMEA 2000® Considerations
NOTICE
If you are connecting to an existing NMEA 2000 network, identify the NMEA 2000
power cable. Only one NMEA 2000 power cable is required for the NMEA 2000
network to operate properly.
An NMEA 2000 Power Isolator (010-11580-00) should be used in installations
where the existing NMEA 2000 network manufacturer is unknown.
If you are installing an NMEA 2000 power cable, you must connect it to the
boat ignition switch or through another in-line switch. NMEA 2000 devices will
drain your battery if the NMEA 2000 power cable is connected to the battery
directly.
This device can connect to an NMEA 2000 network on your boat to share data
from NMEA 2000 compatible devices such as a GPS antenna or a VHF radio. The
included NMEA 2000 cables and connectors allow you to connect the device to
your existing NMEA 2000 network. If you do not have an existing NMEA 2000
network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the Technical Reference
for NMEA 2000 Products at
garmin.com/manuals/nmea_2000.
The port labeled NMEA 2000 is used to connect the device to a standard NMEA
2000 network.
| Item | Description |
|---|---|
| 1 | NMEA 2000 compatible Garmin device |
| 2 | GPS antenna |
| 3 | Ignition or in-line switch |
| 4 | NMEA 2000 power cable |
| 5 | NMEA 2000 drop cable |
| 6 | 12 Vdc power source |
| 7 | NMEA 2000 terminator or backbone cable |
| 8 | NMEA 2000 T-connector |
| 9 | NMEA 2000 terminator or backbone cable |
NMEA 0183 Connection Considerations
- The Chartplotter provides one Tx (transmit) port and one Rx (receive) port.
- Each port has 2 wires, labeled A and B according to the NMEA 0183 convention. The corresponding A and B wires of each internal port should be connected to the A (+) and B (-) wires of the NMEA 0183 device.
- You can connect one NMEA 0183 device to the Rx port to input data to this Chartplotter, and you can connect up to three NMEA 0183 devices in parallel to the Tx port to receive data output by this Chartplotter.
- See the NMEA 0183 device installation instructions to identify the transmit (Tx) and receive (Rx) wires.
- You must use 28 AWG, shielded, twisted-pair wiring for extended runs of wire. Solder all connections and seal them with heat-shrink tubing.
- Do not connect the NMEA 0183 data wires from this device to the power ground.
- The power cable from the Chartplotter and the NMEA 0183 devices must be connected to a common power ground.
- The internal NMEA 0183 ports and communication protocols are configured on the Chartplotter. See the NMEA 0183 section of the Chartplotter owner’s manual for more information.
- See the Chartplotter owner’s manual for a list of the approved NMEA 0183 sentences that the Chartplotter supports.
NMEA 0183 Device Connections
This diagram illustrates two-way connections for both sending and receiving
data. You can also use this diagram for one-way communication. To receive
information from an NMEA 0183 device, refer to items 1,2,3, 4, and 5when
connecting the Garmin device. To transmit information to an NMEA 0183 device,
refer to items 1,2,3,6, and 7when connecting the Garmin device.
| Item | Description |
|---|---|
| 1 | Power source |
| 2 | Power/NMEA 0183 cable |
| 3 | NMEA 0183 device |
| Item | Garmin Wire Function |
Device Wire** Function
---|---|---|---
1| Power| Red| Power
2| Power ground| Black| Power ground
3| Data ground| Black| Data ground
4| Rx/A (In +)| Brown| Tx/A (Out +)
5| Rx/B (In -)| Violet| Tx/B (Out -)
6| Tx/A (Out +)| Blue| Rx/A (In +)
7| Tx/B (Out -)| Gray| Rx/B (In -)
If the NMEA 0183 device has only one input (receive, Rx) wire (no A, B, +, or
-), you must leave the gray wire unconnected. If the NMEA 0183 device has only
one output (transmit, Tx) wire (no A, B, +, or -), you must connect the violet
wire to the ground.
NMEA 0183 and Power Cable Pinout
| Pin Number | Wire Function | Wire Color |
|---|---|---|
| 1 | NMEA 0183 TxJA (Out +) | Blue |
| 2 | NMEA 0183 Rx/A (In +) | Brown |
| 3 | NMEA 0183 Tx/B (Out -) | Gray |
| 4 | NMEA 0183 Rx/B (In -) | Violet |
| 5 | Alarm | Yellow |
| 6 | Accessory on | Orange |
| 7 | Ground (shield) | Black |
| 8 | VIN | Red |
Lamp and Horn Connections
The device can be used with a lamp, a horn, or both, to sound or flash an alert when the chart plotter displays a message. This is optional, and the alarm wire is not necessary for the device to function normally. When connecting the device to a lamp or horn, observe these considerations.
- The alarm circuit switches to a low-voltage state when the alarm sounds.
- The maximum current is 1 A, and a relay is needed to limit the current from the Chartplotter to 1 A.
- To manually toggle visual and audible alerts, you can install single-pole, single-throw switches.
| Item | Description |
|---|---|
| 1 | Power source |
| 2 | Power cable |
| 3 | Horn |
| 4 | Lamp |
| 5 | Relay (1 A coil current) |
| 6 | Toggle switches to enable and disable lamp or horn alerts |
| Item | Wire Color | Wire Function |
|---|---|---|
| 1 | Red | Power |
| 2 | Black | Ground |
| 3 | Yellow | Alarm |
J1939 Engine Network Connection Considerations
NOTICE
You must use a Garmin GPSMAP J1939 accessory cable when connecting the
Chartplotter to the J1939 engine network to prevent corrosion due to moisture.
Using a different cable void your warranty.
If you have an existing engine network on your boat, it should already be
connected to power. Do not add any additional power supply.
This Chartplotter can connect to an engine network on your boat to read data
from compatible devices such as certain engines.
The engine network follows a standard and uses proprietary messages.
You should connect only one Chartplotter to one engine network. Connecting
more than one chart plotter to one engine network may result in unexpected
behavior.
The port labeled J1939 is used to connect the device to the existing engine
network. You must route the cable within 6 m (20 ft.) of the engine network
backbone.
The Garmin GPSMAP J1939 accessory cable requires connection to a power source
and proper termination. For more information on connecting to your engine
network, see the manufacturer’s engine documentation.
| Pin | Wire Color | Description |
|---|---|---|
| 1 | Bare | Shield |
| 2 | Red | Power, positive |
| 3 | Black | Power, negative |
| 4 | White | CAN High |
| 5 | Blue | CAN Low |
Composite Video Considerations
This Chartplotter allows video input from composite video sources using the
port labeled CVBS IN. When connecting composite video, you should observe
these considerations.
- The CVBS IN port uses a BNC connector. You can use a BNC to RCA adapter to connect a composite-video source with RCA connectors to the CVBS IN port.
- Video is shared across the Garmin Marine Network, but it is not shared across the NMEA 2000 network.
Specifications
All Models
| Temperature range | From -15° to 55°C (from 5° to 131°F) |
|---|---|
| Material | Polycarbonate plastic and die-cast aluminum |
| Water rating | IEC 60529 IPX7 1 |
| Input voltage | From 10 to 32 Vdc |
| Fuse | 6 A, 125 V fast-acting |
| NMEA 2000 LEN @ 9 Vdc | 2 |
| NMEA 2000 draw | 75 mA max. |
| Wireless frequency | 2.4 GHz @ 17.6 dBm nominal |
GPSMAP 7×2 Plus
| Dimensions (W x H x D) | 22.4 x 14.3 x 5.4 cm (8.8 x 5.6 x 2.1 in.) |
|---|---|
| Display size (W x H) | 15.4 x 8.6 cm (6.1 x 3.4 in.) 7.0 in. diagonal |
| Weight | 0.86 kg (1.9 lb.) |
| Compass-safe distance | 71 cm (28 in.) |
| Max. power usage at 10 Vdc | 24 W |
| Typical current draw at 12 Vdc | 1.5 A |
| Max. current draw at 12 Vdc | 2.0 A |
| Memory card | 2 micro SMD* card slots;32 GB max. card size |
GPSMAP 9×2 Plus
| Dimensions (W x H x D) | 2.56 x 16.2 x 5.2 cm (10.1 x 6.4 x 2.1 in.) |
|---|---|
| Display size (W x H) | 19.7 x 11.4 cm (7.7 x 4.5 in.) 9.0 in. diagonal |
| Weight | 1.27 kg (2.8 lb.) |
| Compass-safe distance | 76 cm (30 in.) |
| Max. power usage at 10 Vdc | 27 W |
| --- | --- |
| Typical current draw at 12 Vdc | 1.3 A |
| Max. current draw at 12 Vdc | 2.3 A |
| Memory card | 2 microSD card slots; 32 GB max. card size |
¹The device withstands incidental exposure to water of up to 1 m for up to 30
min.
For more information, go to
www.garmin.com/waterrating.
NMEA 2000 PGN Information
Transmit and Receive
| PGN | Description |
|---|---|
| 59392 | ISO acknowledgment |
| 59904 | ISO request |
| 60160 | ISO transport protocol: Data transfer |
| 60416 | ISO transport protocol: Connection management |
| 60928 | ISO address claimed |
| 65240 | Commanded address |
| 126208 | Request group function |
| 126996 | Product information |
| 126998 | Configuration information |
| 127237 | Heading/track control |
| 127245 | Rudder |
| 127250 | Vessel heading |
| 127258 | Magnetic variance |
| 127488 | Engine parameters: Rapid update |
| 127489 | Engine parameters: Dynamic |
| 127493 | Transmission parameters: Dynamic |
| 127505 | Fluid level |
| 127508 | Battery status |
| 128259 | Speed: Water referenced |
| 128267 | Water depth |
| 129025 | Position: Rapid update |
| 129026 | COG and SOG: Rapid update |
| 129029 | GNSS position data |
| 129283 | Cross-track error |
| 129284 | Navigation data |
| 129539 | GNSS DOPs |
| 129540 | GNSS satellites in view |
| 130060 | Label |
| 130306 | Wind data |
| 130310 | Environmental parameters (obsolete) |
| 130311 | Environmental parameters (obsolete) |
| 130312 | Temperature (obsolete) |
Transmit
| PGN | Description |
|---|---|
| 126464 | Transmit and receive PGN list group function |
| 126984 | Alert Response |
| 127497 | Trip parameters: Engine |
Receive
| PGN | Description |
|---|---|
| 65030 | Generator average basic AC quantities (GAAC) |
| 126983 | Alert |
| 126985 | Alert text |
| 126987 | Alert threshold |
| 126988 | Alert value |
| 126992 | System time |
| 127251 | Rate of turn |
| 127257 | Attitude |
| 127498 | Engine parameters: Static |
| PGN | Description |
| --- | --- |
| 127503 | AC input status (obsolete) |
| 127504 | AC output status (obsolete) |
| 127506 | DC detailed status |
| 127507 | Charger status |
| 127509 | Inverter status |
| 128000 | Nautical leeway angle |
| 128275 | Distance log |
| 129038 | AIS class A position report |
| 129039 | AIS class B position report |
| 129040 | AIS class B extended position report |
| 129044 | Datum |
| 129285 | Navigation: Route, waypoint information |
| 129794 | AIS class A static and voyage related data |
| 129798 | AIS SAR aircraft position report |
| 129799 | Radiofrequency/mode/power |
| 129802 | AIS safety-related broadcast message |
| 129808 | DSC call Information |
| 129809 | AIS class B TS” static data report, part A |
| 129810 | AIS class B TS” static data report, part B |
| 130313 | Humidity |
| 130314 | Actual pressure |
| 130316 | Temperature: Extended range |
| 130576 | Trim tab status |
| 130577 | Direction data |
NMEA 0183 Information
Transmit
| Sentence | Description |
|---|---|
| GPAPB | APB: Heading or track controller (autopilot) sentence -13″ |
| GPBOD | BOD: Bearing (origin to destination) |
| GPBWC | BWC: Bearing and distance to waypoint |
| GPGGA | GGA: Global positioning system fix data |
| GPGLL | GLL: Geographic position (latitude and longitude) |
| GPGSA | GSA: GNSS DOP and active satellites |
| GPGSV | GSV: GNSS satellites in view |
| GPRMB | RMB: Recommended minimum navigation information |
| GPRMC | RMC: Recommended minimum specific GNSS data |
| GPRTE | RTE: Routes |
| GPVTG | VTG: Course over ground and ground speed |
| GPWPL | WPL: Waypoint location |
| GPXTE | XTE: Cross-track error |
| PGRME | E: Estimated error |
| PGRMM | M: Map datum |
| PGRMZ | Z: Altitude |
| SDDBT | DBT: Depth below transducer |
| SDDPT | DPT: Depth |
| SDMTW | MTW: Water temperature |
| SDVHW | VHW: Water speed and heading |
Receive
| Sentence | Description |
|---|---|
| DPT | Depth |
| DBT | Depth below transducer |
| MTW | Water temperature |
| VHW | Water speed and heading |
| WPL | Waypoint location |
| DSC | Digital selective calling information |
| DSE | Expanded digital selective calling |
| Sentence | Description |
| --- | --- |
| HDG | Heading, deviation, and variation |
| HDM | Heading, magnetic |
| MWD | Wind direction and speed |
| MDA | Meteorological composite |
| MWV | Wind speed and angle |
| VDM | AIS VHF data-link message |
You can purchase complete information about National Marine Electronics
Association (NMEA) format and sentences from
www.nmea.org.
J1939 Information
The Chartplotter can receive J1939 sentences. The Chartplotter cannot transmit
over the J1939 network.
| Description | PGN | SPN |
|---|---|---|
| Engine percent load at the current speed | 61443 | 92 |
| Engine speed | 61444 | 190 |
| Engine manifold exhaust gas temperature – right manifold | 65031 | 2433 |
| Engine manifold exhaust gas temperature – left manifold | 65031 | 2434 |
| Engine auxiliary coolant | 65172 | |
| Active diagnostic trouble codes | 65226 | |
| Vehicle distance | 65248 | |
| Water in fuel indicator | 65279 | |
| Engine wait to start lamp | 65252 | 1081 |
| Engine over-speed test | 65252 | 2812 |
| Engine air shutoff command status | 65252 | 2813 |
| Engine alarm output command status | 65252 | 2814 |
| Engine total hours of operation | 65253 | 247 |
| Navigation-based vehicle speed | 65256 | 517 |
| Engine fuel temperature 1 | 65262 | 174 |
| Engine oil temperature 1 | 65262 | 175 |
| Engine fuel delivery pressure | 65263 | 94 |
| Engine oil pressure | 65263 | 100 |
| Engine coolant pressure | 65263 | 109 |
| Engine coolant temperature | 65263 | 110 |
| Engine coolant level | 65263 | 111 |
| Engine fuel rate | 65266 | 183 |
| Engine average fuel economy | 65266 | 185 |
| Engine intake manifold #1 pressure | 65270 | 102 |
| Battery potential/power input 1 | 65271 | 168 |
| Transmission oil temperature | 65272 | 177 |
| Transmission oil pressure | 65272 | 127 |
| Fuel level | 65276 | 96 |
| Engine oil filter differential pressure | 65276 | 969 |
© 2019 Garmin Ltd. or its subsidiaries
Garmin®, the Garmin logo, ActiveCaptain®, and GPSMAP® are trademarks of Garmin
Ltd. or its subsidiaries, registered in the USA and other countries. These
trademarks may not be used without the express permission of Garmin.
FLIR®is a registered trademark of FLIR Systems, Inc. NMEA®, NMEA 2000®, and
the NMEA 2000 logo are registered trademarks of the National Marine
Electronics Association. microSD®, the microSD logo, SD®, and the SD logo are
trademarks of SD-3C, LLC. Wi‑Fi® is a registered trademark of Wi-Fi Alliance
Corporation. Windows® is a registered trademark of Microsoft Corporation in
the United States and other countries.
© 2019 Garmin Ltd. or its subsidiaries
support.garmin.com
References
- Garmin International | Home
- Garmin Customer Support
- GPSMAP® 722 | Garmin Support Close Close IE Banner
- NMEA 2000 | Garmin Support Close Close IE Banner
- Water Rating Definitions | Garmin
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>