ROCKVILLE HTS56 5.1 Channel Home Theater Audio System with LED Light Effects Owner’s Manual
- June 6, 2024
- RockVille
Table of Contents
HTS56 5.1 Channel Home Theater Audio System with LED Light Effects
COMPONENT CONNECTIONS
1. OPTICAL AUDIO INPUT: Use the optical port to input the sound signal from
any 5.1 channel optical output enabled source such as TVs, Digital set-top
boxes, game consoles, DVD players, Blu-ray players, CD players, etc. Please
note: If you are having issues with sound output, follow these steps:
a. Set your TV’s sound output to external speakers. b. Go into your TV’s audio
settings and make sure to deactivate Dolby Pro-Logic,
Dolby ATMOS, etc. and select PCM format. 2. RCA AUX AUDIO INPUT: Use the RCA
Auxillary jacks to connect computers, cellphones, or any other external sound
source with a 3.5mm output. You will need an RCA to 3.5mm Y cable. 3. DVD
AUDIO INPUT: Use these RCA jacks to input the sound signal from any 5.1
channel output enabled source such as a TV, Digital set-top boxes, game
consoles, DVD players, Blu-ray players, CD players, etc.
OPTICAL AUDIO INPUT
1
2
3
5
POSITIONING THE SPEAKERS
1. Most people place the subwoofer in the front of the room, near the sound
input source, for ease of connection. But since bass frequencies are
omnidirectional the subwoofer can be placed anywhere. Try placing it near a
wall or a corner for increased bass.
2. The center channel speaker should be place directly in front of the
listening position, above or below the sound input source. If possible, tilt
it as necessary to direct the sound to ear level.
3. Mount the front speakers on the wall, directly to the left and right of
the center channel speaker. Angle them towards the listening postion.
Preferably, the tweeters should be at ear level.
4. Mount the satellite speakers on the wall, slightly behind the listening
position, about 1 to 2 feet above ear level. If side placement isn’t possible
place them to the rear of the listening position and angle them forward.
SUB
0°
20° 30°
20° 30°
90° 110°
6
90° 110°
MOUNTING INSTRUCTIONS
Before you begin please make sure you have the proper tools and necessary
accessories. For this installation you will need the following items: ·
mounting brackets and screws (included) · wall hooks (optional, not included)
· speaker cable (included) · drill · Phillips screw driver
Make sure you have all the necessary screws and brackets. There should be five
brackets and one bag of screws. If any of these items are missing, please
contact Rockville.
Using two screws, secure one bracket to the back of each speaker you wish to
mount. If you are mounting the speakers horizontally, you will need to use two
brackets for each speaker.
Now mark on the wall the place where you will be mounting your speakers. Use
the diagram from the POSITIONING THE SPEAKERS section to determine the best
location. Both front speakers should be at the same height; the same goes for
the satellite units. Remember to keep speakers at least two feet away from
corners, and make sure you have enough wire to reach the mounting location.
You can use a screw or a mounting hook to hang the speaker. Use a screw with a
drywall insert or drive it into a wall stud to ensure that it is securely
fastened to the wall. Use a stud finder to locate the stud and to make sure
that there are no wires or cable lines located in that area. Once the mounting
hooks or screws are in place, you are ready to begin mounting. Be sure to wire
each speaker before mounting it to the wall.
7
REMOTE CONTROL FUNCTIONS
: Power/Standby INPUT: Switch between input modes: USB/FM/AUX/DVD/OPT/BT MUTE:
Mute all output 5.1/2.1: Channel mode select SLEEP: set unit to sleep mode LED
LIGHT: Set subwoofer LED light mode/turn
off speaker LEDs SAVE: Save stations to unit memory TUNE +/ : Manually tune
FM stations
: Play/Pause in USB/SD/BT modes AUTO: Automatic station search CH / :
Previous FM station/previous track (USB/SD) CH +/ : Next FM station/next track
(USB/SD) FL +/ : Front left speaker volume control FR +/ : Front right
speaker volume control SW +/: Subwoofer volume level CEN +/ : Center speaker
volume control VOL +/: Master volume control SL +/ : Front left speaker
volume control SR +/ : Front right speaker volume control 0 9: Number pad
used to direct select tracks
when in USB/SD mode REPEAT: Repeat one song/repeat all songs/shuffle RESET:
Reset volume level MIC +/ (EQ +/- : When a mics are connected, these buttons
will control the mic volume. In USB/SD mode, they will allow you to navigate
the 5 preset EQ curves. Please note: connecting mics will override the EQ +/-
function. ECHO +/ (DISP +/-): When a mics are connected, these buttons will
control the echo effect. If there are no mics connected, they will control the
display brightness. Please note: connecting mics will override the DISP +/-
function.
8
FRONT PANEL
1
2
7
3
4
8
9
5 6
10 9
REAR PANEL
1 2 10
OPTICAL AUDIO INPUT
3
4 5 6 7 8 9 10 11 12
FRONT PANEL
1. Input: Use this key to switch between AUX, SD, USB, OPTICAL, and FM modes.
2. Standby: While in AUX/SD/USB/OPT/FM modes, press and hold for 3 seconds to
enter
standby. 3. Master volume: turn the knob left or right to increase or decrease
the system’s volume. 4. CH / : Previous FM station/previous track in USB/SD
mode. 5. SD card reader 6. USB port 7. Pro-Logic: Pro-logic function key 8.
CH+/ : Next FM station/next track in USB/SD mode. 9. AUTO/ : Press and hold
for 5 seconds for automatic station search /Play-pause
function in USB/SD mode. 10. ¼ MIC inputs: Use these jacks to connect up to 2
microphones for Karaoke.
REAR PANEL
1. Power input 2. Power switch 3. Optical audio input 4. FM antenna 5. RCA
AUX in 6. Front L / R RCA DVD audio input 7. Center /subwoofer RCA DVD audio
input 8. Rear L / R RCA DVD audio input 9. Center RCA audio output 10. Front L
/ R RCA audio output 11. Rear L / R RCA audio output 12. LED power output
11
BLUETOOTH
To connect your iPod, iPhone, MP3 player, Android phone or any other Bluetooth
capable device follow the steps listed below. 1. Make sure the unit is plugged
in and the power switch is in the ON position.
2. Press the INPUT button on the remote control or push the INPUT button on
the unit until the digital read out shows “BT”.
3. Turn on the Bluetooth feature on your device and ensure that it is in
“discoverable” mode. Search for “Rockville HTS56” on your list of available
devices and select it.
4. If your device requires a password, please use “0000”.
FM RADIO
For FM radio follow the steps listed below. 1. Make sure the unit is plugged
in and the power switch is in the ON position. Be sure to
connect the included FM antenna.
2. Press the INPUT button on the remote control or push the INPUT button on
the unit until the digital read out shows numbers.
3. To automatically save stations: · Press and hold the AUTO button for 3
seconds. The unit will begin to automatically search and save any available
stations.
4. To manually save stations:
· Use the TUNE +/TUNE – buttons to find a station you like and that is coming
in clearly.
· Press the SAVE button. CHAN will start flashing on the screen. Use the
CH-/CH+ buttons to select the channel number you’d like to program for that
station.
· Press the SAVE button again. This will set the channel & the message “good”
will be displayed.
5. Use the CH-/CH+ buttons to navigate through saved stations or use the TUNE
+/TUNE buttons to manually find a station.
USB/SD
For USB/SD playback, follow the steps listed below. 1. Make sure the unit is
plugged in and the power switch is in the ON position.
2. Press the INPUT button on the remote control or push the INPUT button on
the unit until the digital read out shows “USB” or “SD”.
3. Plug in your SD card or USB flash drive. The unit will automatically read
the files and begin playing music.
OPTICAL INPUT
For audio via optical input, follow the steps listed below. 1. Make sure the
unit is plugged in and the power switch is in the ON position.
2. Plug in your optical audio cable into the optical audio output port of the
sound source. Plug the other end to the optical audio input port of HTS56.
3. Press the INPUT button on the remote control or push the INPUT button on
the unit until the digital read out shows “OP”.
4. Set your TV’s sound output to external speakers.
Please note: If you are having issues with sound output, go into your TV’s
audio settings and make sure to deactivate Dolby Pro-Logic, Dolby ATMOS, etc.
and select PCM format.
12
MIC INPUT
To use the system for karaoke connect any microphone via either one of the ¼
inputs located on the front of the unit. While the MICs are connected, you can
control the mic volume by pressing the MIC- or MIC+ buttons on the remote.
Additionally, you can control the mic echo effect settings by pressing the
ECHO- or ECHO+ buttons on the remote.
TROUBLESHOOTING
PROBLEM
SOLUTION
No power No sound
vimeo.com/473203709
Make sure the unit is plugged in and the power switch is in the ON position.
1. Make sure you’ve selected the proper source. 2. Make sure all speakers are
properly connected. 3. Check individual speaker volume controls as well as the
master volume. 4. Check the input source’s volume settings. 5. Make sure
you’ve selected external speakers in your TV’s sound ouput settings. 6.
Deactivate Dolby Pro-Logic, Dolby ATMOS, etc. andselect PCM in your TV’s sound
format settings. 7. Check all connections between the receiver and the input
source. Go to the URL or scan the qr code on the left for helpful information.
No sound from mics
1. Make sure the mics are turned on and properly connected. 2. Adjust the mic volume on the remote control. 3. Check individual speaker volume controls as well as the master volume.
Bluetooth pairing fails
1. Check to see that both devices are turned on and that your Bluetooth
device is discoverable.
2. Turn both devices off and then on again.
3. Make sure you’ve selected the proper source.
4. Make sure that the Bluetooth device is within 5 feet of the unit.
5. Move both devices away from other Bluetooth devices, microwaves, wireless
routers, and other electronics.
6. Make sure that the unit is not paired to a previously paired device.
No SD or USB memory device playback
1. Make sure you’ve selected the proper source, USB/SD (see page 11).
2. Make sure that the audio files are in the proper format (see page 14).
3. Make sure you are not exceeding the SD card and
USB drive size limitations (see page 14).
4. Make sure that the SD card or USB drive is properly plugged in.
5. Check the SD card or USB drive for damage.
Poor or no radio reception 1. Make sure antenna cables are properly connected and above the unit.
13
FEATURES/SPECIFICATIONS
· HTS56 5.1 Channel Home Theater System with LED Light Effects · Plug and play
system with everything you need right out of the box · 1000 Watts Peak Power ·
500 Watts Program Power · 250 Watts Continuous RMS Power · 8 Subwoofer with
built-in receiver · 1 x 3 Center Channel Speaker · 2 x 3 Full Range Front
Channel Speakers · 2 x 3 Full Range Rear Channel Speakers · Top-quality MDF
wood cabinets with plastic front panels · Built-in FM receiver with amazing
reception · Digital display · 5 preset EQ curves · You can independently
control the volume of each speaker and the subwoofer · Bluetooth v2.1 · USB
input (max file size: 16Gb) · SD input (Minimum card capacity is 512Mb, max
file size: 16Gb) · Acceptable file formats: MP3, WMA, APE, FLAC, and WAV. · 2
¼ MIC inputs with echo function for karaoke · 5 RCA Audio outputs · 6 RCA DVD
Audio inputs · 2 RCA AUX inputs · Optical audio input · FM antenna input ·
Full function remote · The subwoofer unit has 4 LED lighting modes: (blink to
the beat, solid on, spectrum EQ
analyzer, off) and selectable with 7 colors or multi-color mode. · Cable
Length: Front L/F: 12Ft, Rear L/R: 23Ft, Center: 10Ft · Frequency Response:
20Hz 20KHz · Certification: CE and RoHS Compliant · Amplifier: Class AB,
very efficient amplifier with top components! · Signal to noise ratio: 70dB
(Maximum output with THD+1<1%) · System Impedance: 8 driver: 8 Ohm /3 driver:
4 Ohm · Max SPL: 106 dB @ 1w/1m · THD: 1% · Input voltage: 120V/60Hz ·
Subwoofer Dimensions in Inches: (WDH) 9.25 x 13.19 x 14.57 · Center Speaker
Dimensions in Inches: (WDH) 3.94 x 4.13 x 14.57 · Front L/R Satellite
Speaker Dimensions in Inches: (WDH) 3.94 x 4.13 x 14.57 · Rear L/R Satellite
Speaker Dimensions in Inches: (WDH) 3.94 x 4.13 x 9.25 · Shipping Dimensions
in Inches: (WDH) 18.58 x 12.99 x 21.34 · Net Weight: 26.47 LBS · Shipping
Weight: 28.68 LBS
14
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Responsible party name: Rockville Address: 600 Bayview Ave,
Entrance A, Inwood, NY 11096 Hereby declares that the product Rockville HTS56
complete powered home theater system complies with FCC rules as mentioned in
the following paragraph: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation
between the equipment and receiver. · Connect the equipment to an outlet on a
circuit different from that to which the
receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
15
RockvilleAudio.com
© 2020 ROCKVILLE // Features and specifications are subject to change and or
improvement without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>