veho Cave VHS-010-OC HD Outdoor Wireless IP Camera User Manual
- June 6, 2024
- veho
Table of Contents
hd outdoor wireless IP camera
VHS-010-OC
Introduction to the Cave HD Outdoor IP Camera
Before pairing the Cave camera with your Cave Smart Hub please read the following.
Ensure the camera and Smart Hub is within range of the mobile device which you use to access the Cave app.
You will need your router username and password to hand.
IMPORTANT: Only use the supplied power cable with the camera and a compatible power source. Failure to do so may invalidate your warranty.
Visit our YouTube channel for Cave installation guides
https://www.youtube.com/VehoWorld
Installating the Cave camera
Before installation insert a compatible microSD card, class 10 up to 128GB (not included). Remove the two screws that secure the bottom panel and insert microSD card into the slot. Secure the bottom panel in place with the two screws.
We recommend the installation is carried out by a qualified Electrician. Before mounting the camera ensure the mounting surface can easily support the weight of the camera.
Pairing the Cave camera
STEP 1
Once installed and plugged into a compatible power source, the Cave camera LED (on the front) will continuously flash green to indicate it is in pairing mode.
STEP 2
Open the Cave app and press the ‘Add Accessory’ button then press ‘By scanning QR Code’.
STEP 3
Scan the QR Code on the base of the camera using the scan window in the app. Take note of the camera pairing name, shown on screen, next open wi-fi settings on your device.
Note: If the camera does not appear on the wi-fi list press and hold the reset button on the rear of the camera for 10 seconds, when released, you will hear a ‘Beep’. The camera should appear within 30 seconds.
STEP 4
Select the camera from the wi-fi list and enter the default password ‘ 01234567 ’ and click ‘Join’. The camera should connect to your wi-fi.
STEP 5
Re-enter the Cave app your wi-fi router should be already listed, enter your wi-fi router password and confirm the password before clicking ‘Start’. Network configuration may take up to a few minutes.
STEP 6
Enter a name for your new IP camera and click the tick icon to save. The camera will now appear in the Cave app under ‘Smart cameras’.
STEP 7
To view the camera for the first time, you will need to reset the default password. Press ‘OK’ and enter a new password, once confirmed the camera will be online and ready to view.
Live view, recording & playback
Click on the ‘Smart Camera’ icon on the home screen where all IP cameras are listed. For a live view of any camera’s click the play icon on the left. In live view mode, you can take a snapshot, listen to audio and talk through the camera. To review recorded footage click the ‘Video’ link for a list of recorded events. All footage is automatically saved onto a microSD card (not included).
Camera settings
Change camera password / Motion detection & recording / Sync timezone / Record in HD or SD / Horizontal and vertical flip / Update wi-fi settings / Format SD card.
Specifications
Camera
Image sensor| 1/2.7” 1080P CMOS
Effective pixels| 1920(H) x 1080(V)
WDR| Digital WDR
Noise Reduction| 3D DNR
Day/Night control (IR-Cut)| Auto (ICR)/Colour/B&W
Motion detection| Supported
SD card| Supported, up to 128GB
IR distance| 30m (98.5ft)
Lens
Focal length| 4mm
Max aperture| F2.4
Focus control| Fixed
Angle of view| 114°
Video
Encode| H.265 main profile
Resolution| 1080P (1920×1080), VGA (640×352)
Video bitrates| 32Kbps ~ 8Mbps
Video frame rate| 30fps@1080P
Image snapshot| Supported
General
Power supply| DC 12V/1A
Hard reset| Supported
Working power| <5W
Working temp| -10~+55 / 10%~90% RH
Water resistant| IP65
Dimensions| 188mm x 65mm x 60 mm
Weight| 385g
Network
Network protocol| HTTP, FTP, TCP/IP, UDP, SMTP, DHCP, NTP, UPNP, RTSP, Onvif,
DDNS
App| iOS (9.0+), Android (5.0+)
Wi-Fi| Wi-Fi (802.11b/g/n), 2.4G only, supports WEP / WPA-PSK /WPA2-PSK
encryption
P2P| Supported
Support & troubleshooting
How do you reset the Cave HD Outdoor wireless IP Camera?
Press and hold the reset button on the rear of the camera until you hear the
reset success tone, approximately 10 seconds. Release the button and wait
until you hear a beep to confirm the camera is in pairing mode, this can take
up to 30 seconds; proceed to set up the camera after the beep.
Contacting Veho
To contact Veho for support or troubleshooting for your Cave IP Camera visit our website at veho-world.com and use our pop-up chatbox.
DISCLAIMER:
Veho is not responsible for ensuring all footage is captured. Please ensure
the Cave HD Outdoor Wireless IP Camera is installed and positioned correctly,
and you are familiar with operating the camera and app before using.
EC DECLARATION OF CONFORMITY
Hereby, Veho UK LTD declares that the radio equipment type (VHS-010-OC) is in
compliance with Directive 2014/53/EU. The full text of the EU Declaration of
Conformity is available at https://veho-world.com/compliance/
Frequency band(s) – 2.4GHz
Maximum radio-frequency power – 19dBm
This symbol, affixed to the product or its packaging, indicates that the product must not be processed as household waste. This product should be correctly disposed of according to your local guidelines for electrical and battery operated products. Correct disposal of the battery will avoid potential harm to the environment and human health. For further information regarding the recycling of this product, please contact your local waste recycling centre.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>