veho VHS-011-HDC Cave HD Wireless IP Camera User Guide

June 6, 2024
veho

veho - logo

veho VHS 011 HDC Cave HD Wireless IP Camera-

Cave
hd wireless IP camera

VHS-011-HDC

Introduction to the Cave HD IP Camera

Before pairing the Cave HD IP Camera with your Cave Smart Hub please read the following. Ensure the camera and Smart Hub is within range of the phone/device which you use to access the Cave app. You will need your router username and password to hand.

IMPORTANT: Only use the supplied power cable with the camera and a compatible power source. Failure to do so may invalidate your warranty.

Visit our YouTube channel for Cave installation guides https://bit.ly/2GoPtxN

Pairing the Cave IP Camera

veho VHS 011 HDC Cave HD Wireless IP Camera - IP
Camera

STEP 1
Plug the Cave IP Camera into a compatible power source using the supplied power cable. The camera LED will continuously flash green to indicate it is in pairing mode.

veho VHS 011 HDC Cave HD Wireless IP Camera - IP Camera
2

STEP 2
Open the Cave app and press the ‘Add Accessory’ button then press ‘By scanning QR Code’.

veho VHS 011 HDC Cave HD Wireless IP Camera - IP Camera
3| veho VHS 011 HDC Cave HD
Wireless IP Camera - IP Camera 4
---|---

STEP 3
Scan the QR Code on the base of the camera using the scan window in the app. Take note of the camera pairing name, shown on screen, next open wi-fi settings on your device.
Note: If the camera does not appear on the wi-fi list press and hold the reset button on the rear of the camera for 10 seconds, when released, you will hear a ‘Beep’. The camera should appear within 30 seconds.

veho VHS 011 HDC Cave HD Wireless IP Camera - IP Camera
5

STEP 4
Select the camera from the wi-fi list and enter the default password ‘ 01234567 ’ and click ‘Join’. The camera should connect to your wi-fi.

veho VHS 011 HDC Cave HD Wireless IP Camera - IP Camera
6

STEP 5
Re-enter the Cave app your wi-fi router should be already listed, enter your wi-fi router password and confirm the password before clicking ‘Start’. Network configuration may take up to a few minutes.

veho VHS 011 HDC Cave HD Wireless IP Camera - FIG

STEP 6
Enter a name for your new IP camera and click the tick icon to save. The camera will now appear in the Cave app under ‘Smart cameras’.

veho VHS 011 HDC Cave HD Wireless IP Camera - FIG2

STEP 7
To view the camera for the first time, you will need to reset the default password. Press ‘OK’ and enter a new password, once confirmed the camera will be online and ready to view.

Motion Detection & Recording

veho VHS 011 HDC Cave HD Wireless IP Camera - IP Camera
9| veho VHS 011 HDC Cave HD
Wireless IP Camera - IP Camera 10
---|---

 The camera records 18-second video clips 3 seconds of this is pre-recording when movement is detected. The clips automatically save onto a microSD card (not included).
Activate recording
Install a microSD card (up to128GB) and enter the camera settings. Click ‘Motion Detection & Recording’ to activate. To view footage use ‘Play Video Recordings’ under advanced camera settings.

Controlling the Cave HD IP Camera

| Shows all IP cameras connected  to the Cave Smart Hub
---|---
Snapshot and image save, talk through  the camera and listen to audio
Edit camera settings

veho VHS 011 HDC Cave HD Wireless IP Camera - IP
Camera11

Edit camera settings

  •  Motion Detection & Recording
  • Sync time zones
  •  Horizontal/vertical flip corrects camera view.
  • Change wi-fi settings. Press the reset button on the camera for approx 10 secs until you hear a beep, then wait 25 secs before attempting to pair the camera to the Smart Hub again.
  • Format SD card.

Using the camera with a generic app

The Cave IP Camera will work independently from the Smart Hub as a standalone IP camera with a generic (non-Cave) app. We recommend ‘GrapeCam’ available on iOS & Android. Download the app and follow the same pairing instructions as used for the Cave version.

Cave accessories

veho VHS 011 HDC Cave HD Wireless IP Camera
-accessories

Support & troubleshooting

How do you reset the Cave HD IP Camera?
Press and hold the reset button on the rear of the camera until you hear the reset success tone, approximately 10 seconds. Release the button and wait until you hear a beep to confirm the camera is in pairing mode, this can take up to 30 seconds; proceed to set up the camera after the beep.

DISCLAIMER:
Veho is not responsible for ensuring all footage is captured. Please ensure the Cave HD IP Camera is installed and positioned correctly, and you are familiar with operating the camera and app before using it.

veho VHS 011 HDC Cave HD Wireless IP Camera-

EC DECLARATION OF CONFORMITY
Hereby, Veho UK LTD declares that the radio equipment type (VHS-011-HDC) is in compliance
with Directive 2014/53/EU. The full text of the EU Declaration of Conformity
is available at https://veho-world.com/compliance/
Frequency band(s) – 2.40GHz
Maximum radio-frequency power – 14dBm

veho - icon2

This symbol, affixed to the product or its packaging, indicates that the product must not be processed as household waste. This product should be correctly disposed of according to your local guidelines for electrical and battery-operated products. Correct disposal of the battery will avoid potential harm to the environment and human health. For further information regarding the recycling of this product, please contact your local waste recycling center.

veho - logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals