BLAUPUNKT A3P32AT2 Electric Vehicle Charging Cable User Manual

BLAUPUNKT A3P32AT2 Electric Vehicle Charging Cable User Manual

Electric Vehicle Charging Cables (Mode 3)

Apply for model numbers Al P16AT1, AlP32AT1, A 1 P16AT2, A3P16AT2, A 1 P32AT2, A3P32AT2, B1P16AT1, B1P16AT2

Thank you for choosing a BLAUPUNKT EV Charging cable. In order to help you use this product property, please read this User Manual carefully before using the product.

CAUTION

• Make sure chargers are used in a safe, secure place and well out of the reach of young children or pets.
• Do not damage the products maliciously Do not drop the connector or press heavy objects on its surface.
• Do not disassemble or assemble the connector and change the internal parts Do not clean the products using chemicals.
• Do not charge while driving.

Please follow these instructions to avoid the risk of death or serious injury.

Please make sure the connector is fully inserted into the socket.

Portable Charger for Electric Vehicles (Mode 2)

Apply for model numbers ALV21 PT2 Pcrtable Charger for Electric Vehicles A

CAUTION

• Do not Immerse the charger in water.
• Do not damage the products maliciously Avoid dropping the communications box or pressing heavy objects on its surface.
• Keep the charger away from high temperature.
• Do not place the charger In the car or in a confined space when charging.
• The operating temperature of this equipment cannot exceed -30 C to +SO C

WARNINGS

• Use with RCD circuit breaker only.
• Do not use this product if the EV charging cable is damaged.
• For Electric vehicle charging only.
• This product must be grounded property when used.
• Do not put fingers into the charging plug.
• This product does not contain user-serviceable parts, please do not try to repair or maintain the product on your own. If the charger cannot be charged normally according to the User Manual, please contact the dealer for repair or replacement

Product Descriptions

Product Descriptions

• Communication box (LED Screen)
  

24˚C

|

Temperature

---|---

16A

| Rated current
220V|

Voltage

0.000kwh

| Electricity consumption
00:00:00|

Charging time

0.00kw

| Power
0.0A|

Constant current

• Status LED Meaning
  LED   State| Fault Yellow| State Green| Charge  Red
  ---|---|---|---

Ready

| Off| On| Off
EV Connected| Off| Slow Flash|

Off

CP Emor

| Off| Fast Flash| Off
Charging| Off| Pulsing|

Off

Change Complete

| Off| Flash| Off
Fault| Flash| Off|

Off

Specifications

Standards

| IEC 62196-2 SAE 11772
---|---
Rated Voltage|

110/250V AC

Rated   Current

| 8-1013-16A/MMO AC
Rated Frequency|

50Hz/60H

Insulation Resistance

| >10M
Operating Temperature|

-30 ˚C to +50 ˚C

Storage Temperature

| -40 ˚C to + 80 ˚C
Operating Humidity|

5%-95%RH ( non-condensing)

Enclosure

| In-Cable box:IP54 Charging connector: IP54
Weight|

25kg

Precautions

• Make sure that the charger is free from any abnormal conditions, such as laceration, rust, rupture or breakage of charging ports, cables, control boxes, wires, and plug surfaces.

• Please do not use this charger if the socket is damaged, rusted, cracked or loosely connected.

• Do not start using if the plug is dirty or wet Wipe with a clean and dry cloth to
  make sure it is dry and free of dirt.

• Make sure that the plug at the power supply end is consistent with the power supply socket before changing.

How To Start Charging

1. Take out the charging cable and Insert the plug into the power supply socket ( as shown in Fig. 1 )
   

2. Push the blue button on the controller to adjust the current

3. Please remove the protective cap and fully insert the charging connector into the charging port. ( as shown in Fig. 2 ) AMake sure the connector is fully inserted into the socket.

4. If the charging device operates automatically, the red light will always be on, and the green light will be flashing.

How To Stop Charging

1. Disconnect the plug from the outlet socket **(as shown in Fig.3)

**

2. Disconnect the charging connector from the vehicle inlet socket **(as shown in Fig.4)

**

3. Close the protective shell of charging port at the car end, and then cover the protective cap of the charging connector. **(as shown in Fig.5)

**

4. Put the charger into the bag.

Current (Amp) Switching of the Controller

In order to switch charging current, make sure the power plug is firmly inserted into the socket and the end of the EV vehicle is disconnected, and then press the blue switch button. The charging current will be successfully switched.

Support

For After sales service, please call:
Sweden 031 3045 665
Denmark 77 34 33 30
International +45 77 34 33 30
BLP EV Systems ApS
Ediths Alle 8
5250 Odense SV
Denmark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>