OLIGHT Warrior X Pro Lumens Tactical Flashlight User Manual

Warrior X Pro Lumens Tactical Flashlight

USER MANUAL

Warrior X Pro
Thank you for purchasing this Olight Product. Please read
this manual carefully before use and keep it for future
reference!

IN THE BOX

Warrior X Pro (with Battery)

Holster

Lanyard

USB Magnetic Charging Cable

TGR (Tactical Grip Ring)

SPECIFICATIONS

All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the flashlight.
Note: The maximum output brightness will decrease as the battery voltage decreases.

USB MAGNETIC CHARGING CABLE — MCC3

USB type A – magnetic charge connector, length: 0.5m

Input|

USB A – Type DC 5V 2A

Charging pattern| CC&CV
Maximum
charging current| 2A
Voltage of fully charged battery| 4.2V±0.05V
Charge indication|

Red: charging
Green: full (over 95%) or disconnect with flashlight

Time to fully charge|

5.5 hours (For reference only. When the USB power supply
is insufficient to provide 5V 2A power capacity, the
charging time will be longer)

PRODUCT OVERVIEW

BATTERY INSTALLATION

Before first use, unscrew the tailcap and remove the insulating
film within the battery compartment before screwing the tailcap
back on tightly. If the battery needs to be changed, make sure
that the positive polarity side of the battery faces toward the
direction of the flashlight head (the side of the LED).

CHARGING

Vibrating Power Indicator

It helps to alert if the battery is low (power≤30% vibrate once
every 5 minutes; power≤10% vibrate once per minute; power≤
5% vibrate once every 10 seconds).

• Before first use please fully charge the product.
• Connect the USB end of the magnetic charging cable to an external
  USB power source, then attach the other end of the cable to the
  charging port of the light (best charging efficiency with a 10W (5V 2A)
  USB power source). The red indicator means charging, while the green
  indicator means charging completed (battery level95%).
• Only charge with standard MCC3, not compatible with other MCC.

TGR (Tactical Grip Ring) Installation Guide

a. Unscrew the tailcap and remove the O-ring.

b. Then remove the tactical grip ring and pocket clip.

C. Install the TGR and O-ring as shown in the picture and tighten the
tailcap.

DANGER

• DO NOT throw the light directly into human eyes. This may cause
  temporary blindness, or permanent damage to the eyes.

• DO NOT cover the light head when the flashlight is on, or place
  the flashlight head on the ground. The radiation energy of the
  flashlight may cause damage to the flashlight itself, or even
  result in burning to flammable objects.

• DO NOT use Non-protected rechargeable batteries.

WARNING

• Keep out of reach of children.
  •

• prevent the flashlight body from overheating and hurting the
  user’s hand.

• The tail switch may not work while immersed in sea water or
  other conductive media. Please try to keep it clean and dry.

• If the product is left unused or carried and transported, please
  loosen the tailcap a half turn to avoid accidentally activating the
  flashlight.

NOTICE

• DO NOT short circuit the switch cap with the ring outside it for a
  prolonged period. The short circuit in this case will result in a
  loss of current below 3mA, and may lead to a complete battery
  drain if it is in this state for too long.

HOW TO OPERATE

Click the tail switch lightly to produce a low light output or press the tail switch hard to produce a high light output. Single click (click and release quickly) the tail switch to turn the
flashlight on or off.
When you press and hold the switch, the flashlight will be in
momentary mode; when you release the tail switch, it will turn off.

Before first use, unscrew the tailcap and remove the insulating film within the battery compartment before screwing the tailcap back on tightly. If the battery needs to be changed, make sure that the positive polarity side of the battery faces toward the direction of the flashlight head (the side of the LED).

USB power source, then attach the other end of the cable to the charging port of the light (best charging efficiency with a 10W (5V 2A) USB power source). The red indicator means charging, while the green indicator means charging completed (battery level95%).

• Only charge with standard MCC3, not compatible with other MCC.

( EN ) English
HOW TO OPERATE Click the tail switch lightly to produce a low light output or press the tail switch hard to produce a high light output. Single click (click and release quickly) the tail switch to turn the flashlight on or off. When you press and hold the switch, the flashlight will be in momentary mode; when you release the tail switch, it will turn off.

WARRANTY
Within 30 days of purchase: Contact the original seller for repair or replacement. Within 5 years of purchase: Contact Olight for repair or replacement. Battery warranty: Olight offers a one year warranty for all rechargeable batteries. MCC magnetic USB charging cable: One year. The other no warranty fragile or low-value fittings like lanyard and clip, you can contact post-sale in 30 days after purchase if it has quality drawback or damage under normal use condition. Over 30 days or damage under abnormal use condition, the conditional quality assurance will be provided as appropriate.
USA Customer Support cs@olightstore.com Global Customer Support customer- service@olightworld.com Visit www.olightworld.com to see our complete product line of portable illumination tools.

Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.
Made in China
3.0040.6010.9004
F. 09. 28. 2020
THANK YOU!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>