AUSTRALIAN MONITOR XRS8P Passive Powered and Outdoor Loudspeaker User Manual

June 6, 2024
Australian Monitor

INSTALLATION AND OPERATION MANUAL

XRS SERIES
PASSIVE, POWERED AND OUTDOOR LOUDSPEAKERS

XRS8 / XRS10 / XRS12
XRS8P / XRS10P / XRS12P
XRS6ODV / XRS8ODV / XRS10ODV / XRS12ODV

IMPORTANT SAFETY INFORMATION

  1. READ these instructions.

  2. Keep these instructions.

  3. Heed all warnings.

  4. Follow all instructions.

  5. Do not use this apparatus near water.

  6. Clean only with a dry cloth.

  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
    A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

  10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

  11. Only use attachments/accessories specified by the manufacturer.

  12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

  13. Unplug this apparatus during lightning storms or when unused for long periods of time.

  14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

  15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases shall be placed on the apparatus.

  16. Plug this apparatus into the proper wall outlet and make the plug be disconnected readily operable.

  17. The mains plug is used as a disconnected device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.

  18. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

  19. An appliance with a protective earth terminal should be connected to a mains outlet with a protective earth connection.

  20. The apparatus should be disconnected from the mains completely before speaker wiring. The speaker output should be properly protected from direct contact and pay attention to speaker connections, terminals, and speaker wiring during normal operation.

INTRODUCTION & CONTENTS

XRS SERIES
The Australian Monitor XRS series of two-way injection-molded speakers are specifically designed to suit both live sound reinforcement and permanent installation. From front-of-house to fold back, the dance floor to background fill, the XRS series with passive and powered options are designed with flexibility and performance in mind. For outdoor applications, there is also the ODV range. These models provide the same high performance as the passive models but are IP44 rated with zinc-coated grills, captive cables and feature a built-in transformer for high or low impedance installation. Both the passive and powered ranges include 8″, 10″, and 12″ models, with high-quality compression drivers and represent excellent audio quality and great value for money. The ODV range also includes a compact 6″ version which is perfect for smaller outdoor areas.

Version 2.0: August 2021

WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT USE THE PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT & FULLY INSERT.

CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.| TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
---|---
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.|

For European Union countries: This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. Please contact your local authority for further details
of your nearest designated collection point.

Rating plate and caution marking are marked on the back enclosure of the apparatus

FRONT PANEL

All versions

  1. High-Frequency Driver
    Horn-loaded compression driver.
    Dispersion 90° H x 60° V for XRS6ODV and 90° H x 90° V for all other models
    Passive crossover in the passive and outdoor XRS variants.XRS6ODV| 1”
    ---|---
    XRS8| 1.5”
    XRS10| 1.5”
    XRS12| 2”

Active crossover and power amp in XRS powered varients.

XRS8P 50 W
XRS10P 50 W
XRS12P 100 W
  1. Low-Frequency Woofer
    Driver sizes:XRS6ODV| 6”
    ---|---
    XRS8| 8”
    XRS10| 10”
    XRS12| 12”

REAR PANEL

Passive and Constant Voltage

  1. Speaker Input
    The input connector is a 4 pole twist lock, a speakON compatible connector. Pins 1+ and 1- are wired to +ve and -ve respectively of the speaker. The XRS10 and XRS12 have two connectors. They are wired in parallel so either connector can be used as an input, the other as a loop through.

  2. Voltage Tap Select Switch
    A switch on the back of the XRS ODV speakers allows you to select the desired transformer tap. Each speaker has 3 taps at 70 V and 100 V, as well as a low impedance transformer bypass option.

  3. Fly Lead (Speaker Input)
    The XRS ODV series speakers come supplied with a 2 core flying lead as input to the speaker. The flying lead wires are red (positive +) and black (negative -) and are used as an input to the speaker for both constant voltage and low impedance inputs.

Powered Version

  1. Mic In
    Balanced XLR microphone input.

  2. Mic Signal
    Green LED Signal Present indicator for the Mic input. It indicates the signal present on the input and is not affected by the level control.

  3. Line In
    Balanced XLR line-level input.

  4. Line Signal
    Green LED Signal Present indicator for the Line input. Indicates signal is present at the input, it is not affected by the level control.

  5. Line Out
    LINE OUT is a line-level output. This output can be connected to the LINE IN on another XRS Powered speaker to expand the system.

  6. Output Clip
    Red LED clip indicator for mixed mic and line audio signals. Some flashing of red is acceptable on program transients. Continuous flashing of red could indicate that undue stress is being placed on the speaker and will sound distorted. Turn down the input level until the clip LED is no longer lit.

  7. Mic Level
    Controls the level of the MIC input (1).

  8. Mic Bass
    Bass control for the MIC input (1). There is 12 dB of cut and boost at 100 Hz. This EQ is the shelving type.

  9. Mic Treble
    Treble control for the MIC input (1). There is 10 dB of cut and boost at 10 kHz. This EQ is the shelving type.

  10. Line Level
    Controls the level of the LINE input. (3)

  11. Line Bass
    Bass control for the LINE input (3). There is 12 dB of cut and boost at 100 Hz. This EQ is the shelving type.

  12. Line Treble
    Treble control for the LINE input (3). There is 10 dB of cut and boost at 10 kHz. This EQ is the shelving type.

  13. Power Switch
    Mains power switch to turn the speaker amplifier on and off.

  14. IEC Mains Input Socket
    XRS series-powered speakers use a standard IEC 3 pin mains socket. A standard IEC mains cable is provided. The fuse drawer contains the main fuse and a spare. The main fuse is a time lag (slow blow) HRC 20 x 5 mm ceramic or glass type fuse.| XRS8P| XRS10P| XRS12P
    ---|---|---|---
    115 V| 2.5 A| 2.5 A| 3.15 A
    230 V| 1.6 A| 1.6 A| 5.0 A

IMPORTANT: Always replace the fuse with one of the same value and type.
NOTE: Always disconnect power to the amplifier before replacing fuses.

  1. Voltage Select Switch
    This switch selects the main voltage for your region. Choose either 230V or 115V.
    IMPORTANT: Disconnect power to the amplifier before operating this switch.
    IMPORTANT: Always ensure that the correct voltage for your area has been chosen before connecting the unit to the main supply. Failure to do so may result in personal injury or damage to the unit.

MOUNTING

When mounting XRS series loudspeakers the following safety issues must be considered;

  1. The mounting of a permanently installed speaker may be dangerous unless undertaken by a qualifified professional with relevant experience.
  2. Walls and mounting surfaces must be capable of supporting the speaker and bracketry in a safe and secure manner.
  3. Fixings must be safely attached to the speaker cabinet and the mounting surface. All fixings must be installed in accordance with the manufacturer’s instructions and specifications.

Suspending with Eyebolts
As many eyebolt locations as possible should be used on the speaker.

XRS6ODV or XRS8 speaker cabinet, at least two or more mounting points must be used.

XRS10 and XRS12 speaker cabinets, three or more points must be used.

The best way to hang a speaker using eyebolts is to use two eyebolts on the top of the cabinet and one on the rear to give the speaker some angle.

All eyebolt fittings in the XRS range are M8 and require at least 20 mm of thread length.

ACCESSORIES

XRS6ODV

PART| DESCRIPTION
XR6PMA| Pole mount adaptor
XRS8
PART| DESCRIPTION
XR8PMA| Pole mount adaptor
XR8UMB| Universal mounting bracket
XRS10
PART| DESCRIPTION
XR10CVR| Heavy-duty cover
AMISLSB2| Wall mount brackets
ATC303| Tripod speaker stand
ATC304| Heavy-duty tripod speaker stand
ATC305| Winch up speaker stand
XR10-12UB| Universal bracket
XRS12
PART| DESCRIPTION
XR10CVR| Heavy-duty cover
AMISLSB2| Wall mount brackets
ATC303| Tripod speaker stand
ATC304| Heavy-duty tripod speaker stand
ATC305| Winch up speaker stand
XR10-12UB| Universal bracket

SPECIFICATIONS

PASSIVE MODELS XRS8 XRS10 XRS12
IMPEDANCE 8 Ohms 8 Ohms 8 Ohms
POWER (CONTINUOUS, PROGRAM) 100 W, 200 W 250 W, 500 W 300 W, 600 W
SENSITIVITY (1 w i 1 M) 92 dB 95 dB 97 dB

CALCULATED MAX SPL

(CONTINUOUS, PEAK)

| 112 dB, 118 dB| 119 dB, 125 dB| 121 dB, 128 dB 90° x 90°
DISPERSION (-6 dB POINTS) (H X V)| 90° x 90°| 90° x 90°| 90° x 90°
FREQUENCY RESPONSE (-3 dB)| 65 Hz- 18 kHz| 55 Hz – 18 kHz| 50 Hz – 18 kHz
FREQUENCY RESPONSE (-1 ods)| 60 Hz – 20 kHz| 50 Hz – 20 kHz| 40 Hz – 20 kHz
CONNECTION| 4 pole twist-lock connectors| 4 pole twist-lock connectors| 4 pole twist-lock connectors
COMPONENTS| 1 x 8″ Woofer,

1 x 1.5″ HF Driver

| 1 x 10″ Woofer,

1 x 1.5″ HF Driver

| 1 x 12″ Woofer, 1 x 2″ HF Driver
NET DIMENSIONS

(W X D X H) (per single)

| 277 x 257 x 400 mm (10.9″ x 10.1″ x 15.7″)| 321 x 308 x 464 mm (12.6″ x 12.1″ x 18.3″)| 415 x 382 x 620 mm (16.3″ x 15.0″ x 24.4″)
SHIPPING DIMENSIONS

(W X D X H) (per pair)

| 595 x 310 x 460 mm (23.4″ x 12.2″ x 18.1″)| 375 x 355 x 535 mm (14.8″ x 14″ x 21.1″)| 465 x 435 x 680 mm (16.3″ x 15.4″ x 23.6″)
NET WEIGHT (per single)| 6.5 kg (14.3 Ibs)| 10 kg (22 Ibs)| 18 kg (39.7 Ibs)
SHIPPING WEIGHT (per pair)| 15 kg (33.1 Ibs)| 12 kg (26.5 Ibs)| 20 kg (44.1 Ibs)
PASSIVE MODELS| XRS8P| XRS10P| XRS12P
---|---|---|---
CALCULATED MAX SPL (CONTINUOUS, PEAK)| 112dB, 118 dB| 119 dB, 125 dB| 121.8 dB, 127.8 dB
DISPERSION (-6 dB POINTS) (I-I X V)| 90° x 90°| 90° x 90°| 90° x 90°
FREQUENCY RESPONSE (-3 dB)| 65 Hz- 18 kHz| 55 Hz – 18 kHz| 50 Hz – 18 kHz
FREQUENCY RESPONSE (-10dB)| 55 Hz – 18 kHz| 50 Hz – 18 kHz| 40 Hz – 20 kHz
AMPLIFIER TYPE| Class AB| Class AB| Class AB
POWER REQUIREMENTS (VAC)| 115/230 V, 50/60 Hz| 115/230 V, 50/60 Hz| 115/230 V, 50/60 Hz
POWER OUTPUT| 100 W (LF) + 50 W (HF)| 100 W (LF) + 50 W (HF)| 300 W (LF) + 100 W (HF)
CONNECTION| 3 Pin XLR| 3 Pin XLR| 3 Pin XLR
COMPONENTS| 1 x 8″ Woofer,
1 x 1.5″ HF Driver| 1 x 10″ Woofer,
1 x 1.5″ HF Driver| 1 x 12″ Woofer,
1 x 2″ HF Driver
NET DIMENSIONS (WXDXH)| 277 x 257 x 400 mm
(10.9” x 10.1” x 15.7”)| 277 x 257 x 400 mm
(10.9” x 10.1” x 15.7”)| 415 x 382 x 620 mm
(16.3” x 15.0” x 24.4”)
SHIPPING DIMENSIONS

(WXDXH)

| 355 x 325 x 470 mm
(14″ x 12.8″ x 18.5″)| 375 x 355 x 535 mm
(14.8″ x 14″ x 21.1″)| 465 x 435 x 680 mm
(16.3″ x 15.4″ x 23.6″)
NET WEIGHT| 8.6 kg (19 Ibs)| 10.5 kg (23.1 Ibs)| 23 kg (51 Ibs)
SHIPPING WEIGHT| 10.1 kg (22.3 Ibs)| 11.8 kg (26 Ibs)| 25.2 kg (55.6 Ibs)
OUTDOOR MODELS| XRS6ODV| XRS8ODV
---|---|---
IMPEDANCE (Bypass)| 8 Ohms| 8 Ohms
POWER (70 V, 100 V Tappings)| 7.5 W, 15 W, 30, 60 W| 15 W, 37.5 W, 75 W
POWER (Bypass Continuous / Program)| 80 W, 160 W| 100 W, 200 W
SENSITIVITY (1 W / 1 M)| 92 dB| 92 dB
CALCULATED MAX SPL (CONTINUOUS, PEAK)| 111 dB, 117 dB| 112 dB, 118 dB
DISPERSION (-6 dB POINTS) (H X V)| 90° x 60°| 90° x 90°
FREQUENCY RESPONSE (-3 dB)| 95 Hz – 18 kHz| 65 Hz – 18 kHz
FREQUENCY RESPONSE (-10dB)| 85 Hz – 20 kHz| 60 Hz – 20 kHz
CONNECTION| Captive Fly Lead| Captive Fly Lead
COMPONENTS| 1 x 6” Woofer 1 x 1” HF Driver| 1 x 8″ Woofer, 1 x 1.5″ HF Driver
NET DIMENSIONS (W X D X H)| 225 x 200 x 325 mm (8.9” x 7.9” x 12.8”)| 277 x 257 x 400 mm (10.9” x 10.1” x 15.7”)
SHIPPING DIMENSIONS (W X D X H)| 260 x 260 x 390 mm (10.2” x 10.2” x 15.4”)| 355 x 325 x 470 mm (14” x 12.8” x 18.5”)
NET WEIGHT (per single)| 7 kg (15.4 lbs)| 10 kg (22 lbs)
SHIPPING WEIGHT (per pair)| 8.2 kg (18 lbs)| 12 kg (26.5 lbs)
OUTDOOR MODELS| XRS10ODV| XRS12ODV
---|---|---
IMPEDANCE (Bypass)| 8 Ohms| 8 Ohms
POWER (70 V, 100 V Tappings)| 37.5 W, 75 W, 150 W| 37.5 W, 75 W, 150 W, 300 W
POWER (Bypass Continuous / Program)| 250 W, 500 W| 300 W, 600 W
SENSITIVITY (1 W / 1 M)| 95 dB| 97 dB
CALCULATED MAX SPL (CONTINUOUS, PEAK)| 119 dB, 125 dB| 121 dB, 127 dB
DISPERSION (-6 dB POINTS) (H X V)| 90° x 90°| 90° x 90°
FREQUENCY RESPONSE (-3 dB)| 55 Hz – 18 kHz (8 Ohm Bypass)| 50 Hz – 18 kHz (8 Ohm Bypass)
FREQUENCY RESPONSE (-10dB)| 50 Hz – 20 kHz (8 Ohm Bypass)| 40 Hz – 20 kHz (8 Ohm Bypass)
CONNECTION| Captive Fly Lead| Captive Fly Lead
COMPONENTS| 1 x 10″ Woofer, 1 x 1.5″ HF Driver| 1 x 12″ Woofer, 1 x 2″ HF Driver
NET DIMENSIONS (W X D X H)| 321 x 308 x 464 mm (12.6” x 12.1” x 18.3”)| 415 x 382 x 620 mm (16.3” x 15.0” x 24.4”)
SHIPPING DIMENSIONS (W X D X H)| 375 x 355 x 535 mm (14.8″ x 14″ x 21.1″)| 465 x 435 x 680 mm (16.3” x 15.4” x 23.6”)
NET WEIGHT (per single)| 16.5 kg (36.4 lbs)| 22 kg (48.5 lbs)
SHIPPING WEIGHT (per pair)| 18.5 kg (40.8 lbs)| 24 kg (52.9 lbs)

ENGINEERED BY AUSTRALIAN MONITOR
Address: Unit 1, 2 Daydream Street, Warriewood NSW 2102 Australia
Website: www.australianmonitor.com.au
International inquiries email: international@australianmonitor.com.au
ABN 86 003 231 187

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Australian Monitor User Manuals

Related Manuals