Fiido Electric Bike M3 User Manual
- June 6, 2024
- Fiido
Table of Contents
M3(On-Road) User Manual
SHENZHEN FIIDO TECHNOLOGY DEVELOPMENT CO., LTD
NO.142 Fiido Industrial Park, Futong Rd. Yuanshan St. Longgang District,
Shenzhen, China
https://www.fiido.com
email：support@finido.com
Fiido Electric Bicycle Catalog
I.Important note
II.Bike diagrams
III.How to adjust the saddle height
IV.Unfolding instructions
V.Folding instructions
VI.Specifications
VII.Daily maintenance and basic troubleshooting
E-Scooter and E-Bike laws differ by State – check your local laws and only ride
in legally permitted areas.
Use helmets, protective gear, and always ride responsibly.
Riding Safety
As with other sports, bicycling involves the risk of personal injury and
damage to the bicycle. By choosing to ride a bicycle, you assume the
responsibility for that risk, so you need to know – and practice – the rules
of safe and responsible riding and of proper use and maintenance. Proper use
and maintenance of your bicycle reduce the risk of injury.
Because it is impossible to anticipate every situation or condition which can
occur while riding, this Manual makes no representation about the safe use of
the bicycle under all conditions. There are risks associated with the use of
any bicycle which cannot be predicted or avoided, and which are the sole
responsibility of the rider.
If you have any questions or do not understand something, take responsibility
for your safety and consult with the bike shop or the bicycle’s manufacturer.
It is important for a rider to read carefully all instructions below before
your first ride.
Important Note
This manual includes important safety performance and service information.
Please make sure to read the following warnings before using our products for
the first time.
a) If you lend your e-bike to other people, please confirm that he/she has read
this manual to decrease the risk of an accident.
b) Please wear a suitable and safe helmet before riding, please wear clothes
with fluorescent and reflective stripes when riding at night.
Follow the traffic rules and don’t exceed the speed limits, which may cause
accidents.
c) Don’t touch or use metal to touch the charging port on the bike, it will
cause a short circuit.
d) Following actions will cause huge power drops and reduce the riding
distance:
- Start the bike by using the throttle.
- Frequent braking.
- Riding against the wind.
- Overloading
- Insufficient tire pressure.
e) To extend the riding range :
- Please use assist mode.
- Brake only when necessary for safety, and don’t use the throttle to start the bike.
- Don’t overload.
- Before riding, please check the tire pressure and supply enough pressure.
f) When charging the e-bike, please make sure that there is nothing inside of the charging port. Connect the charger to the bike first and then to the AC power source to avoid sparking.
g) Please consult your insurance company or insurance broker on the insurance coverage of riding an electric bike.
h) Generally, people must be 16 years old to ride an e-bike or three-wheel electric bike. Please refer to local laws and regulations when using this product in your country.
i) Bicycles are vehicles with certain risks, brake the rear wheel first, and then the front wheel in emergency braking, especially when the cycling speed is too high, you may fall over if you use the front brake suddenly. Please ride carefully.
Safety Guidelines
- Always ride with both hands on the handle.
- Do not park in building doors, evacuation staircases, walkways, and safety exits.
- Do not charge inside residential buildings and park
- Stay away from the combustible when charging.
- Please charge according to the suggested time, do not charge for too long.
- Use and store the batteries correctly; batteries should never be disassembled.
- Read all warning terms before riding or charging, only use the original charger.
- When adjusting the saddle position, do not exceed the safety line on the seat post.
Bike Diagrams
1. Seat tube
2. Seat-post clamp
3. Brake disc
4. Motor
5. Chain
6. Shock absorber
7. Controller box
8. Folding system| 9. Battery box
10. Charge port
11. Chain wheel
12. Pedal
13. Crank
14. Handlebar
15. Stem
16. Folding system
17. Front light
---|---
1. Power-Off /Rear Brake
2. Bell
3. Power button
(3-2.Click turn— on/off front & rear light）
(3-1. Long press turn— on/off electric power mode)| 4. Power adjustment
(Click once to shift gears, a total of 3 gears)
5. Battery Level
(Display remaining battery)
6. Speed
(Display current speed)
7. Light on the indicator| 8. Electric-assist power level
(Display power level)
9. USB output port
（Output 5V for charging）
10. Power-Off /Front Brake
11. Gear indicator
(Display current gear)| 12. Gear adjust handle
(Press the handle to reduce the gear tooth)
13. Gear adjust handle
(Press the handle to reduce the gear tooth)
14. Electric-assist throttle
(Provide electric assistant)
---|---|---|---
Note: The bike will automatically shut down when it is stationary if notes.)
13. Hold and press with your fingers, folding the pedal.
**
**
14. Battery charging port located below the main beam of the frame)
**
**
15. Insert the charger port Standard charger)
**
**How to adjust the saddle height
Battery seat tube:
Open the seat-post clamp (Figure 2), pull the battery seat-post out of the
frame, and adjust the height of the battery seat-post up and down according to
your needs.
After you adjust the height of the battery seat-post, then buckle the seat-
post clamp.
2. Adjust to the right seat height for you
3. Adjust the height of the seat tube, and finally buckle the seat-post clamp to secure it.
Unfolding Instructions
- Fold the riser to the upper end, lock the riser folding handle, adjust the riser safety hook to the tightening state, and adjust the position of the T handle.
- Install the front wheel; First, install the front wheel on the front fork and lock the front wheel with screws.
- Open the clip on the seat tube clamp and insert the seat tube into the position within the marking line on the seat tube. Adjust the seat to a comfortable height according to individual needs, and fasten the seat tube clip.
4. Please confirm the following items before riding: frame lock, standpipe
lock, and seat tube lock are locked.
5. Brake system is normal. Tires are adequately inflated. All these are
important for safe and comfortable riding.
Folding Instructions
Step 1. Open the quick lock on the head end and make the handle perpendicular
to the care frame.
Step 2. Open the quick lock on the Stem, lower the riser, and lock the quick
lock.
Step 3. Open the Seat Tube quick-lock, decentralized seat, and lock the quick
lock.
Note: Both the riser and the seat tube are marked with a safe (MAX or
MIN). For safety reasons, please use them in a safe range.
| | 
---|---|---
Step 4. Rotate the buckle on the riser clockwise, pull down the folded part,
and fold it down.
Step 5. Open the frame holder of the fuse buckle, pull the folded part and the
frame.
Specifications
Name
|
Specification
---|---
Electric Bike System| Fiido System
Power Assist System| 3 Gears Assist
Max Load weight| 120kg
Maximum Power assist Speed| 25km/h
Maximum Range| Power-assisted model up to 60KM-80KM
Battery| High-quality Lithium-ion 48V 11.6Ah
Battery adaptation| DC 54.6V 2A
Recharge Time| 7 hours
Drive Type| Rear Drive
Frame Material| Aluminum Alloy
Brake Type| Mechanical Disc Brakes
Chainset| 52T
Gears| Shimano 7 speed
Chain| KMC Z7
Rear Brake| Mechanical Disc Brakes
Rear Hub/Rated Power| CZJB Motor/250W
Rims| Alloy
Wheel Size| 20″
Tyre Size| 20″x4.0 inch
Tyre Brand| Cheng Shin Tire
Net Weight| 25kg
Folded Size| 96cm45cm79cm
Size| 172cm26cm106cm
• The above data allow for 5% manufacturing tolerances.
• After receiving the goods, there may be some differences between individual
accessories and display drawings, which are different due to the different
batches, and do not affect the use.
Including : Charger, Front & Rear light, Bell, Controller, Display, Mileage,
Tire, Light/Speaker button, Brakes, Rear derailleur, etc.
Daily maintenance and basic troubleshooting
Brake abnormal sound or wheel rotation resistance| 1. Check whether the end
of the brake cable is stuck.
---|---
2. Slight friction can be adjusted by fine-tuning the end of the line
3. Adjust the brakes to ensure that the brake pad and brake disc clearance is
balanced
4.11 the brake pads are worn, replace brake pads.
Seat tube slide down| 1. The set screw of the Seatpost clamp is not
tightened.
2. Check whether the anti-skid bushing inside the seat tube clamp is damaged,
if it’s broken, replace the anti-skid bushing.
Difficulty in folding bicycle| 1.0 heck whether the spring at the folding
joint is out of shape, or the spring is pulled out without return, if the
spring is damaged, it needs to be replaced.
2. Dry folding joints cause folding difficulties, can use lubricating oil to
lubricate the joints.
Handlebars are not straight| 1. Loosen the standpipe fixing screw, readjust
the handlebar, and then tighten the standpipe fixing screw.
Saddle loose (slide up and down)| 1. Check whether the saddle fixing screw is
tightened. Retighten the saddle bottom fixing screw with the hex tool
2. The loose fixing screw of the saddle slides up and down, resulting in the
sliding teeth of the rack of the seat tube clamp code needing to replace the
seat tube clamp code.
The chain often falls off| 1. Check whether the chainset is deformed and if
the chainset is deformed, it needs to replace the chainset
2. Check whether the rear derailleur is loose, relock the rear derailleur and
then lock the screw.
Fault code
|
Cause of the malfunction
E001| Communication issues
E002| Throttle issues
E003| Brake lever issues
E004| Motor hall issues
E005| Motor issues
E006| Controller issues
•When the battery is used up, it should be fully charged in time. The green
light on the charger indicates a full charge. Long-term underpowered storage
will affect the performance
•When crossing the pool, water section, please pay attention to the wading
height is not higher than the hub, preventing motor damage due to water inflow.
Do not use high pressure so as not to damage the electronic components and
wiring due to humidity.
•Add some lubricating oil to the chain and flywheel of the bike to avoid wading
and rusting
•It is best to charge the battery in a ventilated, dry place. Direct sunlight
or rain can have a bad effect on the performance of batteries and chargers.
When charging, the battery and charger should be away from other sources of
heat.
•Connect the battery before charging and then plug it into the electric
supply. After charging, pull out the electricity first, and then pull out the
battery end. I do not follow it will cause a fire when connecting the battery
end.