Fiido D3 Pro Mini Folding Electric Bike User Manual

Fiido D3 Pro Mini Folding Electric Bike User Manual

Dear user：

In this manual,we will introduce the specification,installation,usage,precautions,and maintenance of FIIDO D3 Pro.Be sure you know everything you need to know about the bike that introduced in this manual. Any questions,please contact Fiido After-sales Team or our Local Service Center,and a prompt reply and feasible solution will be provided.

Safety precautions

1. Please follow the precautions in this instruction to effectively reduce When you enter public areas, please obey national and local regulations, remain vigilant while riding, and maintain a reasonable safe distance from other people and vehicles.

2. Please operate by the instruction of the user manual, the loss caused by not following the instructions shall be borne by

3. This product is not professional off-road vehicle, do not use this product according to off-road vehicle

4. For the first time riding, please do not choose the area with many children, pedestrians, pets, vehicles, or other obstacles and potential Please be familiar with the bike before riding on public road.

5. Before each ride, please carefully check whether fasteners are loose or parts are If there’s any unusual noise, please stop riding immediately, and contact after-sales team for assist.

6. To reduce the injury risk, please read and follow all “Caution”, “Danger” and “warning” instructions in this user No speeding, and do not ride in motorized road under any circumstances.

7. For safety consideration, user must be over 16 years Users under the following circumstances are strongly not recommended to use this product:

   • People affected by alcohol or
   • People who are unable to engage in strenuous physical activity due to
   • People who are unable to maintain balance or whose balance is impaired by motor
   • People whose weight exceeds the max load limit (max load is 120KG/265lb).
   • Pregnant

8. Please ride carefully in snow, rain, wet road, ice and other bad Do not ride over too high or too large obstacles, otherwise it’s very likely to lose balance or grip and cause injuries.

9. Do not attempt to charge while the charger or power supply is wet, please follow the local safety regulations if you need to charge the bike in public

10. For effective protection and as convenient as possible for yourself, please be sure to use Fiido specific
    If you need to retrofit your bike,Please follow the local laws and regulations, after consulting with Fiido after-sales team, then proceed with caution. Serious injury and/or damage caused by unauthorized modification will result in the void of

1.1  Bike overview

Fiido D3pro, as the smallest folding electric bicycle in the Fiido D series, has been admired by users for its lightness and convenience since the model enter the market. D3pro inherited the simple aesthetic style of Fiido, which comes with the sleek and smooth design. The bike only weight 17.3kg and can be carried by one hand. Equipped

with 7.8Ah capacity battery hidden in the frame, it only takes 5 hours to be fully charged. 250W powerful motor and greater torque can provide a lower power consumption, and yet can easily overcome the slope. It’s the first choice of entry-level electric bike for urban commuting.
Fiido D3pro has 3 riding modes and 3 power assisted mode, to provide you with a richer riding experience. The front of the bike can be folded and pushed after folding, to extend more beautiful life scenes.

1.2 Packing list

Bike parts

Bike accessories

Tools

*Please carefully check whether all items are complete and intact. If there is any problem such as missing or damaged, 3 please contact the official after-sales team asap.

1.3 Bike Diagrams

*Non professionals are forbidden to assemble and disassemble the battery.
Please contact after-sales team for assistance.

1.4 Function DESC

Handlebar

Battery

2.1 Installation guide

The basic installation of the bike has been completed before out of the factory. When you receive the bike, you only
need to unfold the bike, install the seat and pedals

Unfold the stem

1. Open the quick release, adjust the handlebar to the right position. Lift the stem and close the stem clamp to settle it
   Caution: Please operate by the instruction, otherwise may cause wire breaking.

2. Close the stem clamp and turn the safety hook into the stem clamp.Adjust the handlebar to suitable height and close the quick release of the stem
   Caution: The safety line should be within the stem.
   

3. Adjust the handlebar direction, to make it at an angle of 15°-20° with the horizontal line, then close the quick release, to complete the unfolding stem.

Install the seatpost

1. Open the seat clamp, insert the seatpost battery

2. Adjust the seatpost to suitable height, the recommended height is when the saddle is level with the user’s pelvis when standing naturally.The height of the adjustment can NOT exceed the safety line.

3. Lock the seat clamp. (the recommended height is when the saddle is level with the user’s pelvis when standing naturally.

The height of the adjustment can NOT exceed the safety line.)

Install pendals

Use the open spanner of the tools bag, screw the pedal shaft into the threaded hole and tighten it in the direction of the arrow.
Caution: While installing the pendal, pay attention to the left / right pendal corresponding to the left / right crank, the pendal screw and the inside of the crank are respectively marked L(left) / R(right). Please install the pendal correctly to prevent it from sliding out of the crank.

2.2 First time using

Before riding, please follow the installation guide to install components properly, check whether the firmware is loose, ensure sufficient power, and take appropriate protection for riding.

Step 1：Adjust the seat

Please adjust the seat to the appropriate riding height according to your height. （the recommended height is when the saddle is level with the user’s pelvis when standing naturally.
The height of the adjustment can NOT exceed the safety line）

Step 2：Turn on the power

Press the“M”button for 3 seconds,when the display lights it start working,same instruction for turning off the power

Step 3：Mode switching

Switch and choose the riding mode according to the cycling road conditions and personal needs.
① Electric mode：Equipped with pure electric mode, gently press down the electric mode button to switch to the pure electric mode, the stonger the press, the faster the speed
② Power assisted mode：Equipped with 3 power assisted gears, click the power assisted gear button to switch the gear. The 1st gear is suitable for relatively flat road conditions, the more/higher the road slope, the larger gear can be adjusted accordingly.
Attention: When the bike is on PAS 3 status, click the power assisted gear button again and the bike will be on PAS 0 status, by then the gear display wont’t be lighted and the The motor will be tuen off.But other components can work as well. The bike will be on pedalling mode.

Step 4：Start riding

Please take corresponding protection before starting riding.

Step 5：Braking introduction

The left side is front brake, the right side is rear brake.
While riding, it’s recommended to use the rear brakefirst, then the front brake to slow down the speed to stop, in order to avoid falling accident caused by balance problems from urgent front wheel brake.

The M button of the meter can be used for the power control of the bike, please follow the below instruction

1. Long press the M button of the meter until the indicator light is on, which means the power has been turned on.

2. Long press the M button of the meter until the indicator light is off, which means the power has been turned off.

How to remove the seatpost

1. Open the seat clamp, lift the seatpost until it’s fully removed from the bike, to complete the seatpost removal.

2.3 Charging instructions

The battery comes with a small amount of electricity, before the first time use, please make sure to charge it to full power before riding.

Charging

1. Charging connection: Connect the charging interface of the charger to the charging port, then connect the power plug of the charger to the power socket.
2. Fully charged：When the indicator light of the charger is red, means it’s normal charging. When the light is green, means it’s fully charged.
3. Charging hour: Charging hour is around 5 hours, The duration depends on the situation.
4. Disconnect charging: When the indicator light turns green, means it’s fully charged. Unplug the power plug first, then remove the charging interface from the battery. Close the battery dust cover.

Caution: Charger has high voltage device, DO NOT repair without permission. In order to avoid danger, battery and charger should be placed away from children. There should be no inflammable and explosive objects around the batteries (such as car seat cushions, sofas, etc.). Keep the battery in a ventilated and dry place, and make sure NOT to charge in open-air place, to avoid electrical short circuit fire and other accidents caused by rain and other factors, and to prevent liquid and metal particles into the electrical parts.
Danger: Charging can be allowed on public charging equipment, but the matching between the bettery and the charging equipment should be fully considered.
Warning: If there’s any odor or high temperature during charging, please stop charging immediately and contactafter-sales team for assist.

2.4 Folding instructions

Lower the seatpost

Lift the seat clamp upward, to keep it in open status. Gently press down the seatpost to the bottom. Press down the seat clamp to keep it in closed status

Fold the stem

Open the stem safety hook, turn the stem clamp downward to keep it in open status. Gently turn the stem downward to the bottom, to finish the stem folding.

3.1  Using precautions

（Ⅰ）Users should pay attention to the safety of bicycle use

1. No parking in building foyers, evacuation stairs, walkways and safety
2. No charging in residential Charging should be far away from combustible, and no longer than 7 hours.
3. Prevent water from entering electrical When cleaning the bike, avoid water impact on charging port, wiring harness connectors, fuse and other electrical parts.
4. When adjusting the height of the saddle, the safety line mark of the seatpost should not be
5. Users and dealers must not wiring and modifying structure and performance without Such as: change the battery configuration, the circuit, increase the lamp power, increase the sound and other modification.
6. Do not touch the live part of the bike with wet hands or metal Such as: charging port, charger plug etc.
7. When replacing circuit breakers or fuses, use circuit breakers or fuses of the specified models and specifications. Do not short-fuse The circuit breaker or fuse card slot should be in good contact, or may cause the accidents.
8. Please do not disassemble electrical parts without authorization to prevent liquid and metal particles from infiltrating into electrical
9. Do not ride on bad weathers, or place the bike in a long-term exposure to the sun/rain to avoid parts
10. If scrub the bike is needed, please wipe the body with a neutral lotion mixed with tap Do not remove and wash internal parts to avoid short circuit.

Caution: Non-professionals are strictly prohibited to repair. In case of failure, please contact the after-sales team or authorized professional maintenance station for maintenance

（Ⅱ）Riding safety: please follow the national and local traffic laws and

regulations, pay attention to riding safety.

1. User must be over 16 years Do not lend to people who can not operate the bike to avoid the harm.
2. Please ride in Non-Motor Vehicle Lane, with the max speed no more than 25km/h.
3. Please carry persons or goods in accordance with local laws and regulations while
4. Please be sure to wear a suitable safety helmet and fasten the helmet wind strap while
5. The braking distance will be extended in rainy and snowy days, please pay attention to slow down, and try to avoid to ride on bad Inner short circuit and electrical parts damage may be caused if the water level reaches the center of the hub of the rear wheel motor, please noticed.
6. Please follow the local traffic rules No riding after drinking, and make sure to always ride with both hands.
7. Bright colors, relaxed, and comfortable suit are suggested for riding, and wear low-heeled shoes for riding is

（Ⅲ）Examination before riding: please repair in time or go to the local

maintenance point for repair, if there’s any abnormality.

1. Please confirm the normal power use when using the kickstand and the rear wheel is off the
2. Turn on the power, check whether the indicator light is normal, and the power supply is sufficient.
3. Check whether the mechanical bell and front/rear light are in good
4. Confirm whether the handlebar and seatpost are adjusted to the appropriate position, that fastening screws and quick release are Be attention that the safety line should not be exposed.
5. Check the front/rear brake handle, brake adjustment should make the brake reliable and flexible
6. Check whether the tire pressure is normal, no cracking, abnormal wear, nails, stones, glass and other sharp
7. Check whether the front/rear wheel screws are locked, the side, rear and pedal reflectors are in good
8. Check whether the front /rear lighting is normal and ensure that lights can be good used while
9. Check the fastening state of each axle to ensure the front/rear axles are in a reliable
10. Check whether the frame clamp is locked before

Caution: abnormal tire pressure, tire cracking damage and abnormal wear are the main causes of steering failure and tire burst.

（Ⅳ）Attentions on the road

1. For your safety and the safety of others, please obey the local traffic rules
2. Before riding, be sure to wear a safety helmet, take safety precautions and maintain a natural
3. At the beginning of riding, please slowly accelerated, to avoid the energy waste or
4. For a longer service life of the battery and motor, when start riding or climbing, please try to use power assisted
5. To ensure safety, economic speed should be used as far as possible, and reduce frequent braking, frequent start as far as possible, to save
6. avoid the phenomenon of tightening the speed control handle after
7. Riding on muddy areas or uneven roads should use pendal mode as far as
8. Braking distance should be appropriately increased on bad weathers, please be concentrated and careful while
9. Equipped with overcurrent protection. The circuit may be overcurrent under the condition of higher uphill Angle and higher headwind It’s better to use pendal mode, otherwise, power consumption may be too fast to affect the range, motor and electrical appliances burn. The body and electrical parts should not be electriferous, the insulation resistance value shall not be less than 2M ω.
10. Controller has undervoltage protection, the power will be cut off automatically if the voltage is lower than the undervoltage value, to maintain the service life of the

（Ⅴ）Attentions of pushing and parking

1. The power should be off when pushing the bike, to avoid the
2. Parking should be on the level ground, and maintain the bike as power off

17  3. For your safety, please maintain and clean your bike regularly to keep it in the best condition.

3.2 Bike maintenance & repair

1. The bicycle has been checked and adjusted before out of factory, any problems please contact Fiido After Sales Team for
2. Normally the spokes of the wheel should be adjusted once after half a month of riding to ensure the best
3. Make sure to check the storage capacity of the tire regularly to keep it in normal
4. Make sure to check the main parts like handlebar, saddle, seatpost, front/rear and centre axle, flywheel and chain, wheels, to keep it in normal use, nut and screw loose should be tightened in time if it loose.
5. In use, it’s recommended to add 3# calcium base lubricating oil (butter) every six months to the parts that need lubrication (such as front/middle/rear axle bearing, front fork bowl group, foot pedal bearing, etc.). Add 30# oil to the chain, brake cable, support and other parts every two months
6. If the vulnerable parts are damaged, such as: brake line, brake skin, brake pad, bulb, fuse, Please find the local maintenance center to replace, but be sure to replace with the same model specifications of the parts.

Cautions: Handlebar core screw fastening torque, combined handlebar joint screw fastening torque, saddle clamp screw fastening torque, front wheel fastening torque recommended torque is not less than 18NM;The recommended torque for fastening the central shaft lock mother and rear wheel is not less than 30NM. Handlebar and saddle tube safety line should not be exposed outside the body.

3.3 Motor maintenance & repair

1. Equipped with rare earth permanent magnet DC brushless, external rotor hub motor, without any deceleration mechanism and carbon brush, which is basically maintenance-free.
2. Do not open the motor base and end cover after
3. Keep the motor clean, no foreign matter, corrosive liquid, gas into the motor, do not knock and bake the motor shell, so as not to damage the

Caution: If the fault cannot be removed, please consult after-sales team.

3.4 Battery maintenance & repair

1. Lithium battery has the characteristics of large capacity, long life, maintenance-free, light weight, pollution-free Its service life is closely related to using mode. Do not store chronically, please form the habit of frequent charging.
2. It is recommended to charge for 5-7hours each time, and the longest time is not more than 1 Lithium battery has no memory effect, can be used with the charge.
3. Make sure to charge for more than two hours every month under chronically store Do not store the battery at a loss of power. Once the battery voltage reaches the discharge state, will cause unrecoverable damage.

Danger: Do not dismantle old battery without authorization, it should be collected according to regulations. Warning: Do not near the fire or high temperature source, or throw it into the fire, or expose it to the sun.

3.5 Reflex reflector cautions

1. Reflex reflector device must not be missing, if it’s missing, please immediately contact after-sales team for replacement, and the installation position should be consistent with the original
2. Fiido reflex reflector has been fixed on the vehicle, please do not change the position, modify, disassemble,
3. Make sure to check the normal function of reflex reflector before each use, and keep the surface
4. The reflector device must not be covered by luggage, children’s chairs, clothing and other objects, otherwise it may cause safety

4.1 Troubleshooting methods

Fault code description

General fault

Through-supply motor failure

| Poor contact of regulating handlebar Poor contact of brake cut-off switch Motor damage

Controller damage Loosened connector

| Change regularing handlebar Change brake cut-off switch Change motor

Change controller or get repair Check the connector

Lack of range

| Tire pressure deficiency Undercharged or faulted charger Aging battery or damaged battery More uphill, gale, frequent braking,

overload, etc

| Blow up the tire

Fully charged, check charger Change battery

Using pendal mode

Difficulty in charging

| Loosened plug Disconnected battery cable Damaged charger| Tighten socket and connector Welded connector

Change charger

Speed failure or low speed than 10KM/h

| Poor contact of regulating handlebar Loosened connector

Battery overvoltage

| Change regulating handlebar Check the connector

Fully charged

4.2  Specifications ****

Product size

| Before folding: LengthWidthHeight (mm)| 1240575980
After folding: LengthWidthHeight (mm)| 1240300610
Tires （Inch）| 14*2.125
Product weight| Net weight (kg)| 17.3

Riding requirement

| Maximum load (kg)| 120
Applicable age| 16+
Applicable height| 155cm(5.0′) – 200cm(6.5′)

Main spec

| Serial numbe Location| Under the frame
Maximum speed| 15MPH (25km/h）
Maximum climb| 25%
Center distance between wheels (mm)| 870
Power assisted system| 3 gears
Transmission ratio| 52T:12T
Applicable road| Urban asphalt pavement/flat pavement
Operating temperature| -10° ~50°
Waterproof rate| IP54
Rated voltage (V)| 36

Battery

| Battery type| Lithium battery
Rated capacity (Wh)| 280.8

Battery management system

| Overheat/short circuit/ overcurrent and overcharge protection

Motor

| Rated power (W)| 250
---|---|---
Rated speed（r/min）| 370
Moter type| Brushless geared motor
Undervoltage protection (V)| 29±1
Overcurrent protection (A)| 13±1

Charger

| Input voltage (V)| 100-240
Output voltage (V)| 42
Output current (A)| 2
Charging hours (h)| 5

Others

| Front light| LED
Tail light| LED
Riding mode| Power assisted mode+Pedal mode

Caution：

• The above data allow for 5% manufacturing
• After receiving the bike, there may be some differences between individual accessories and display drawings, which are different due to the different batches, and do not affect the

4.2 Warranty coverage

(Ⅰ）Warranty principle

1. Users should operate correctly according to this user manual. In case of performance failure caused by production quality, according to relevant laws and national provisions of the three guarantees, the company shall uniformly perform the obligations of the three
2. The faults beyond the warranty scope and the main parts after the warranty period shall be repaired by the company but shall be charged at the
3. Regards the battery replacement after the warranty period, will be charged with the factory price, but the old battery must be returned to the manufacturer, to ensure safety and avoid environmental

(Ⅱ）Warranty scope and period

Basic parts

| Frame| 36 months| Natural deformation, open welding, desoldering fracture phenomenon, quality problems caused by poor manufacturing can be replaced. Self-modification, collision damage, etc. are not warranted.
Fork, Handlebar, Stem, Seatpost| 12 months
Kickstand, Tires, Saddles, Fenders, Safety hook, Seat clamp,

Stem clamp, Frame clamp, Pedals, Brakes, Brake discs, Brake levers

|

3 months

|

Tire puncture by sharp objects, collision damage of spare parts, etc. are not warranted.

Crank chain disc, Front arm set, Hub, Wheel hub, Spokes, Shift finger dial, Derailleur, Flywheel, Chian,

Bottom bracket, Shock absorber

|

6 months

|

Man-made damage, self-modification, collision damage of parts and accessories are not warranted.

Electrics parts

| Controller| 12 months|

Short circuit, burnout, performance failure due to poor manufacturing can be replaced. Water, disconnection,

and man-made damage are not warranted.

Charger, Main wiring harness| 12 months
Display instrument, Speed control knob,

Booster,Controller cover plate

|

6 months

Headlights, Taillights, Power-off brake levers, Switches| 3 months
Motor parts|

Motor, Hall, Bearing, Clutch

|

12 months

| Phase loss, Hall element burnout, demagnetization, abnormal bearing noise can be replaced.

Breakage, water ingress are not warranted.

Battery|

Lithium battery

|

12 months

| Replace the battery due to faults such as broken grids, no power storage, and less than 70% capacity.

No warranty for water ingress or man-made damage.

(Ⅲ）The scope and content exceed warranty

1. Failure caused by user’s failure to use, maintain and adjust according to the User
2. Failure caused by private modification.
3. Failure caused by improper use or storage by users or
4. No warranty card, or card and bike do not
5. Vulnerable parts and consumables, including plastic parts, spokes, rim, brake line, scratching surface
6. The expenses for self-repair without the consent of the specially contracted maintenance
7. After accessories leaving the factory, shell scratches or shell damage will not enjoy
8. Lead scratches or 24

Warranty notification

1. Accessories will be guaranteed in strict accordance with the warranty
2. The warranty period shall be calculated from the date of
3. No warranty will be provided if the charger, battery and motor are disassembled without
4. For other parts of the bike, the quality issues will be provided three months warranty , others will not be
5. When other parts of the bike has issues, maintenance must be carried out in a professional maintenance centre, not private Controllers, batteries, chargers must be ensured that all labeling integrity.
6. maintenance must comes with the warranty card, invoice, certificate of quality and other relevant
7. The battery warranty method is 1:1. In case of battery problems, the battery should be returned to the manufacturer to determine whether the battery is covered by warranty according to battery testing

4.3 Repair record

Warranty card

User

| Company|
---|---|---
Name|  | Phone|
Address|
Purchase date|  | Color|
Model|  | Order No|
Frame No|  | Motor No|

Repair record

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>