Fiido M3 Off Road Folding eBike User Manual

June 4, 2024
Fiido

Fiido M3 Off Road Folding eBike User Manual

Fiido M3 Off Road Folding eBike.JPG

SHENZHEN FIIDO TECHNOLOGY DEVELOPMENT CO.,LTD

NO.142 Fiido Industrial Park,Futong Rd. Yuanshan St. Longgang District, Shenzhen, China

https://www.fiido.com email:support@fiido.com

Made in China

E-Scooter and E-Bike laws differ by State – check your local laws and only ride in legally permitted areas. Use helmets, protective gear and always ride responsibly.

Riding Safety
As with other sports, bicycling involves risk of personal injury and damage of the bicycle. By choosing to ride a bicycle, you assume the responsibility for that risk, so you need to know – and to practice – the rules of safe and responsible riding and of proper use and maintenance. Proper use and maintenance of your bicycle reduces risk of injury.

Because it is impossible to anticipate every situation or condition which can occur while riding, this Manual makes no representation about the safe use of the bicycle under all conditions. There are risks associated with the use of any bicycle which cannot be predicted or avoided, and which are the sole responsibility of the rider.

If you have any questions or do not understand something, take responsibility for your safety and consult with the bike shop or the bicycle’s manufacturer. It is important for rider to read carefully all instructions below before your first ride.

I. Important Note

This manual includes important safety performance and service information. Please make sure to read the following warnings before using our products for the first time.

  1. If you lend your e-bike to other people, please confirm that he/she has read this manual to decrease the risk of accident.

  2. Please wear a suitable and safe helmet before riding, please wear clothes with fluorescent and reflective stripes when riding at night. Follow the traffic rules and don’t exceed the speed limits, which may cause accidents.

  3. Don’t touch or use metal to touch the charging port on the bike, it will causes short circuit.

  4. Following actions will cause huge power drops and reduce the riding distance:
    1. Starting the bike by using the throttle.
    2. Frequent braking.
    3. Riding against the wind.
    4. Overloading.
    5. Insufficient tire pressure.
    1. Please use assist mode.
    2. Brake only when necessary for safety, and don’t use the throttle to start the bike.
    3. Don’t overload.
    4. Before riding, please check the tire pressure and supply enough pressure.

  5. To extend the riding range :

  6. When charging the e-bike, please make sure that there is nothing inside of the charging port. Connect the charger to the bike first and then to the AC power source to avoid sparking.

  7. Please consult your insurance company or insurance broker on the insurance coverage of riding an electric bike.

  8. Generally, people must be 16 years old to ride an e-bike or three-wheel electric bikes. Please refer to local laws and regulations when using this product in your country.

  9. Bicycles are vehicles with certain risks, brake the rear wheel first, and then the front wheel in emergency braking, especially when the cycling speed is too high, you may fall over if you use the front brake suddenly. Please ride carefully.

Safety Guidelines

  1. Always ride with both hands on the handle.
  2. Do not park in building doors, evacuation staircases, walkways, and safety exits.
  3. Do not charge inside residential building and park
  4. Stay away from combustible when charging.
  5. Please charge according to suggested time, do not charge for too long.
  6. Use and store the batteries correctly; batteries should never be disassembled.
  7. Read all warning terms before riding or charging, only use the original charger.
  8. When adjusting the saddle position, do not exceed the safety line on the seat-post.

II. Bike Diagrams

FIG 2 Bike Diagrams.JPG

  1. Seat tube
  2. Seat-post clamp
  3. Brake disc
  4. Motor
  5. Chain
  6. Shock absorber
  7. Controller box
  8. Folding system
  9. Battery box
  10. Charge port
  11. Chain wheel
  12. Pedal
  13. Crank
  14. Handle bar
  15. Stem
  16. Folding system
  17. Front light

FIG 3 Bike Diagrams.JPG

( Note: The bike will automatically shut down when it is stationary if not used within 10 minutes.)

FIG 4 Bike Diagrams.JPG

III. How to adjust the saddle height

Battery seat tube:

Open the seat-post clamp (Figure 2), pull the battery seat-post out of the frame, and adjust the height of the battery seat-post up and down according to your needs.

After you adjust the height of the battery seat-post, then buckle the seat- post clamp.

FIG 5 How to adjust the saddle height.JPG

IV. Unfolding Instructions

  1. Fold the riser to the upper end,lock the riser folding handle,adjust the riser safety hook to the tightening state,and adjust the position of the T handle.
  2. Install front wheel; First install the front wheel on the front fork and lock the front wheel with screws.
  3. Open the clip on the seat tube clamp and insert the seat tube into the position within the marking line on the seat tube. Adjust the seat to the comfortable height according to individual needs, and fasten the seat tube clip.

FIG 6 Unfolding Instructions.JPG

4.Please confirm the following items before riding: frame lock, standpipe lock and seat tube lock are locked.
5.Brake system is normal. Tires are adequately inflated. All these are important for a safe and comfortable riding.

V. Folding Instructions

Step 1. Open the quick lock on the head end and make the handle perpendicular to the care frame.
Step 2. Open the quick lock on the Stem, lower the riser, and lock the quick lock.
Step 3. Open the Seat Tube quick lock, decentralized seat and lock the quick lock.
Note: Both the riser and the seat tube are marked with a safe (MAX or MIN). For safety reasons, please use them in a safe range.

FIG 7 Folding Instructions.JPG

VI. Specifications

FIG 8 Specifications.JPG

FIG 9 Specifications.JPG

  • The above data allow for 5% manufacturing tolerances.
  • After receiving the goods, there may be some differences between individual accessories and display drawings, which are different due to the different batches, and do not affect the use. Including: Charger, Front & Rear light, Bell, Controller, Display, Mileage, Tire, Light/Speaker button, Brakes, Rear derailleur etc.

VII. Daily maintenance and basic trouble shooting

FIG 10 Daily maintenance and basic trouble
shooting.JPG

FIG 11 Cause of the malfunction.JPG

  • When the battery is used up, it should be fully charged in time. The green light on the charger indicates full charge. Long-term underpowered storage will affect the performance of the battery.
  • When cross the pool, water section, please pay attention to the wading height is not higher than the hub, prevent motor damage due to water inflow. Do not use high pressure water gun to clean, so as not to damage the electronic components and wiring due to humidity.
  • Add some lubricating oil to the chain and flywheel of the bike to avoid wading and rusting
  • It is best to charge the battery in an ventilated, dry place. Direct sunlight or rain can have a bad effect on the performance of batteries and chargers. When charging, the battery and charger should be away from other sources of heat.
  • Connect the battery before charging, and then plug it into the electric supply .After charging, pull out the electricity first, and then pull out the battery end. If do not follow the steps, it will cause a fire when connecting the battery end.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals