Princeton Tec ALLOY-X Dual Fuel LED Pen Light Instruction Manual

June 6, 2024
Princeton Tec

Princeton logo x12

ALLOY-X®

DUAL FUEL

LED PEN LIGHT

Princeton Tec ALLOY-X Dual Fuel LED Pen Light

Operating and Maintenance Instructions

LED Charging Indicators

The LED on the positive end of the battery housing lights up when the cable is correctly installed.

  • Charging – Red LED is illuminated.
  • Fully Charged – Green LED is illuminated.

Charge time is approximately 4.5 hours.

IMPORTANT: Maximum charging temperature range is 20°F to 115°F with optimal temperature range between 50°F and 86°F. A safety circuit prevents charging outside the maximum range and the red charge LED will pulse rapidly. When temperature is within an acceptable range charging will resume.

Battery Installation

­- See Battery Installation Diagram

Alloy-X uses one 10900 Lithium Rechargeable Battery, as supplied by Princeton Tec. It is also compatible with 2 AAA Alkaline batteries.

When not using Alloy-X, separate the head and tail by turning counterclockwise approximately one turn. This will prevent accidental activation. Remove batteries when storing Alloy-X.

Observe proper battery polarity when installing the batteries. Improper installation of the batteries will damage light and void warranty.

WARNING    ****
  • Never mix fresh and used batteries.
  • Never mix different battery brands or chemistry types.
  • Always remove drained batteries immediately.
  • Remove batteries during long periods of storage.
Switch Operation

-­ See Figure 2

ON/OFF

With the light off, a full press of the tail switch will produce an audible “click” and the light will turn on. The default is MEDIUM output. Another full press will turn the light off.

Brightness Adjustment

From ON , a half press of the tail switch will cycle through the three output modes. Default is to turn on in MEDIUM. The next half press will produce LOW which is then followed by HIGH and then a return to MEDIUM. The cycle will repeat.

From OFF, a full press will turn the light on the next mode in the cycle. For example, if the light is on in MEDIUM and then turned off, the next full press from OFF will turn the light on in LOW. If the light is turned off, the next click will result in HIGH. The cycle will repeat.

Note: If the light is left off more than one minute it will reset to the default which is turning on in MEDIUM.

Figure 1 ­- Battery Replacement

1

ALLOY-X - Figure 1 - 1
2

ALLOY-X - Figure 1 - 2
3
Rechargeable Battery

ALLOY-X - Figure 1 - 3a

2 AAA Alkaline

ALLOY-X - Figure 1 - 3b

Figure 2 -­ Switch Operation

ALLOY-X - Figure 2a - 1

Standard operation:

Press 1x: On / Medium

From Medium
Quickly press 2x (off and on) : Low

From Low
Quickly press 2x (off and on) : High

Press 1x from On:
Off

Alternate operation

From Medium
Half press 1x (no click) : Low

** From Low
Half press 2x:** (no click) : High

From Medium
Half press 3x: (no click) : High

From Off:
Cycle-memory continues for one minute, then resets

Figure 3 ­- Performance

Note: performance is based on Princeton Tec rechargeable battery. AAA output will be somewhat lower.

Modes Lumens Runtime Beam Pattern

SPOT HIGH

SPOT MED

SPOT LOW

| 400

250

5

| 0.5h

1.25h

28h

| ALLOY-X - Figure 3
DISTANCE (m)| 0                              6                      50 72

(ANSI FL-1 Standard)

Runtime is defined as the duration of time from the initial light output value–defined as 30 seconds after the point the device is first turned on–using fresh batteries, until the light output reaches 10% of the initial value.

Figure 2 ­- Charging

1                            2                                      3

ALLOY-X - Figure 2b - 1      ALLOY-X -
Figure 2b - 2     ALLOY-X - Figure 2b - 3

General Maintenance
  • Do not disassemble the sealed head as doing so may cause damage to the flashlight and void the warranty.
  • Replace the O-rings if they become stretched or damaged. Regularaly lubricate the O-rings.
  • Clean the contacts of your light periodically
Troubleshooting

If the Alloy-X fails to light:

  • Check the battery to see if it needs to be recharged
  • Check the batteries for proper installation.
  • Replace batteries if proper installation is confirmed.
  • Check the PCB board contacts or battery contact for dirt
  • Clean the contct points with an alcohol soaked cotton swab.
USA­ – International 5-Year Warranty

WARRANTY -­ Princeton Tec warrants this product to be free from defects in workmanship and materials under normal use for 5 years. This warranty covers all of the component parts of the product except batteries. This warranty does not cover deterioration due to normal wear or damage due to misuse, alteration, negligence, accidents, or unauthorized repair. Princeton Tec will repair or replace parts which are defective in workmanship or materials.

Your authorized Princeton Tec Dealer and Princeton Tec are the only facilities authorized to repair the product. After (3) unsuccessful attempts (within the warranty period) to repair the product, you have the right to elect replacement of the product or a refund of the purchase price less allowance for use of the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Princeton Tec reserves the right to change product specifications without notice.

FOR CALIFORNIA RESIDENTS:

WARNING: This product contains Bisphenol A (BpA) a chemical known to the State of California to cause birth defects or other reproductive harm.

Return Policy

If your light fails to operate, follow these simple steps:

  1. Check batteries. Replace if necessary.
  2. To send your light in for repair or replacement, first contact Princeton Tec customer service on 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault you are experiencing. No warranty repairs will be accepted without an RMA number.
  3. Return the light without batteries to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be accepted.
  4. Upon receipt your light will be processed in about two weeks. Please allow additional time for return transportation from NJ.

Princeton Tec
PO Box 8057,
Trenton, NJ 08650

Princeton logo x12Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2021 Princeton Tec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Princeton Tec User Manuals

Related Manuals