Princeton Tec RMX300-RD-BK Remix LED Headlamp Instruction Manual
- June 6, 2024
- Princeton Tec
Table of Contents
Princeton Tec RMX300-RD-BK Remix LED Headlamp Instruction Manual
Battery Replacement
Battery Installation
- 3 AAA
- Alkaline (LR03)
- Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and recommends recycling batteries. For more information about battery recycling, please go to: www.batteryrecycling.com
To install the batteries, unlatch the battery door. Open the Remix case by popping the door latch over the catch and rotate the door open.
Install three AAA batteries according to the polarity markings on the inside of the cabinet. Observe proper battery polarity when installing the batteries. Improper installation of the batteries will damage the light and void the warranty.
Rotate the door to the closed position, squeeze the body between your forefingers and thumb to snap the door latch over the catch.
WARNING
- Never mix fresh and used batteries.
- Never mix different battery brands or chemistry types.
- Always remove drained batteries immediately.
- Remove batteries during long periods of storage.
NOTE: Rechargeable NiCad or NiMH batteries may result in reduced brightness due to lower nominal voltage.
Switch Operation
Princeton Tec calculates total burn time as the time it takes for the light source to produce a minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
The Remix has two light sources to choose from, three Ultrabright LEDs or a Maxbright LED. Each light source has two modes (High and Low).
To switch between light sources, press and hold the button down until the light source switches to the desired source. As soon as it switches release the button.
NOTE: If you keep the button pressed the light will continue to switch back and forth between the 5mm and Maxbright LED (on low light settings) until you release the button.
Once you have found your desired light source, you now can select different brightness levels. Your light will start on “low output”. To change to “high output” you must press the button again in less then 1.6 seconds from the previous press. Any additional delay will cause the light to turn off after the next button press.
One final note about the light function – If you have the light turned on,
(and more than 1.6 seconds has passed since your last button press) and you
press and hold the button down to switch light sources, you will be in
darkness for about one second as the light sees this press as a signal to turn
the light off and switch to the other light source simultaneously.
The times listed on the rear of the package assume you have start with fresh
batteries and use only one mode.
Troubleshooting
If the Remix fails to light:
- Check the batteries for proper installation.
- Replace batteries if proper installation is confirmed.
- Check the light for water contamination on the circuit board. The light will resume normal operation once the water is shaken or blown out and the light is left open until completely dry. If the light has been contaminated with salt water, flush the unit with fresh water and dry as described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free from defects in workmanship and materials under normal use for 5 years. This warranty covers all of the component parts of the product except batteries. This warranty does not cover deterioration due to normal wear or damage due to misuse, alteration, negligence, accidents, or unauthorized repair. Princeton Tec will repair or replace parts which are defective in workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton Tec are the only facilities
authorized to repair the product. After (3) unsuccessful attempts (within the
warranty period) to repair the product, you have the right to elect
replacement of the product or a refund of the purchase price less allowance
for use of the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN
THIS WARRANTY. (Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions
may not apply to you.) This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Princeton Tec reserves the right to change product specifications without
notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a chemical known to the
State of California to cause birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
- Check batteries. Replace if necessary.
- To send your light in for repair or replacement, first contact Princeton Tec customer service on 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault you are experiencing. No warranty repairs will be accepted without an RMA number.
- Return the light without batteries to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be accepted. Upon receipt your light will be processed in about two weeks. Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2018 Princeton Tec