Princeton Tec Sector 7 LED Spot Light Instruction Manual

June 5, 2024
Princeton Tec

Princeton Tec Sector 7 LED Spot Light Instruction Manual
Princeton Tec Sector 7 LED Spot Light

Battery Installation

Princeton Tec cares about the environment and recommends recycling batteries. For more information about battery recycling, please go to: www.batteryrecycling.com.

Observe proper battery polarity when installing the batteries. Improper installation of the batteries will damage the light and void the warranty.

Figure 1 – Battery Replacement

Battery Replacement

WARNING

  • Never mix fresh and used batteries.
  • Never mix different battery brands or chemistry types
  • Always remove drained batteries immediately.
  • Remove batteries during long periods of storage.

NOTE: Some battery formulations can emit hydrogen gas. This gas can create an explosion potential in sealed devices if not vented or removed. The Sector 7 is equipped with a platinum catalyst that will remove this gas. When replacing the batteries, visually inspect the LED module for broken or missing catalyst. If the catalyst appears to be damaged, (you may notice gray particles in the battery compartment), or the light has flooded, replace the catalyst before using.

Switch Operation

Switch Operation 
Switch Operation 
Switch Operation 

ON/OFF

With the light off, a single pull of the trigger switch will activate HIGH output

Brightness Adjustment

From HIGH, pull the trigger switch twice to activate LOW. A single pull from LOW willl re-activate activate HIGH After 3 seconds in any mode, a single pull of the trigger switch will turn the Sector 7 OFF

Momentary ON

From OFF pull the trigger switch halfway in to activate Momentary On. Release the trigger switch to turn OFF

O-Ring

  • Occasionally clean and lightly lubricate the O-Ring and lens cap threads. Use only silicone
  • grease, never use aerosol spray lubricants.
  • Clean the contacts of your light periodically

WARNING

  • All plastic components are made of high-impact resistant polycarbonate plastic. Certain forms of aerosol sprays can cause damage and void warranty.
  • To avoid water leakage, do not over tighten the lens cap.

Figure 3 – Performance

Performance

(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value defined as 30 seconds after the point the device is first turned on—using fresh batteries, until the light output reaches 10% of the initial value.

Troubleshooting

As with any equipment, the Sector 7 should be rinsed with fresh water after any contact with salt water. Move the switch and switch lock back and forth a few times while rinsing with water to prevent salt build-up.

Flooding

In the unlikely event your light leaks or is flooded, immediately remove the batteries. Flush all parts with fresh water and allow to dry. Check for possible cause of leakage and correct problem; return light for repair if necessary. Do not reuse batteries that have been wet. Batteries from a flooded light should be discarded.

Troubleshooting

If the Sector 7 fails to light:

  • Check the batteries for proper installation.
  • Replace batteries if proper installation is confirmed

USA– International 5-Year Warranty

WARRANTY – Princeton Tec warrants this product to be free from defects in workmanship and materials under normal use for 5 years. This warranty covers all of the component parts of the product except batteries. This warranty does not cover deterioration due to normal wear or damage due to misuse, alteration, negligence, accidents, or unauthorized repair. Princeton Tec will repair or replace parts which are defective in workmanship or materials.

Your authorized Princeton Tec Dealer and Princeton Tec are the only facilities authorized to repair the product. After (3) unsuccessful attempts (within the warranty period) to repair the product, you have the right to elect replacement of the product or a refund of the purchase price less allowance for use of the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Princeton Tec reserves the right to change product specifications without notice.

FOR CALIFORNIA RESIDENTS:

WARNING: This product contains Bisphenol A (BpA) a chemical known to the State of California to cause birth defects or other reproductive harm.

Return Policy

If your light fails to operate, follow these simple steps:

  1. Check batteries. Replace if necessary.
  2. To send your light in for repair or replacement, first contact Princeton Tec customer service on 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault you are experiencing. No warranty repairs will be accepted without an RMA number.
  3. Return the light without batteries to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be accepted.
  4. Upon receipt your light will be processed in about two weeks. Please allow additional time for return transportation from NJ.

Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2022 Princeton Tec

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Princeton Tec User Manuals

Related Manuals