Princeton Tec VIZZ RGB MPLS Helmet Lights Instruction Manual

October 30, 2023
Princeton Tec

Princeton Tec LOGO

Princeton Tec VIZZ RGB MPLS Helmet Lights

Princeton-Tec-VIZZ-RGB-MPLS-Helmet-Lights-FIG-  \(2\)

Product Information

The Vizz RGB is a headlamp that offers different color options for different situations. It has four color modes: red, green, blue, and white. It also has a dimming function and a lock-out feature to prevent accidental activation and battery drain. The headlamp is powered by 3 AAA batteries and has a waterproof seal to preserve its waterproof integrity. The Vizz RGB also has accessories available, including the MPLS Tactical accessory for attaching the headlamp to an NVG shroud.

Product Usage Instructions

Battery Installation

  1. Open the battery compartment located at the back of the headlamp.
  2. Insert 3 AAA batteries into the compartment, observing proper battery polarity.
  3. Close the battery compartment cover.

Note : It is important to use the correct type of batteries to avoid reduced brightness due to lower nominal voltage.

Switch Operation

  • To turn on the headlamp, press the switch once. Repeat pressing the switch to cycle through the different color modes: red, green, blue, and off. Hold the switch for one second while in white mode to activate dimming.
  • To turn off the headlamp, press the switch once while in anymode or hold the switch for five seconds to activate lock-out.
  • To unlock the headlamp, hold the switch for five seconds while in lock mode or remove and replace the batteries to reset the headlamp to an unlocked state.

Troubleshooting

If the headlamp fails to light up, check if the rear cover is properly installed or if the waterproof seal is dirty. If dirt ispresent, wipe gently with a damp cotton swab and mild soap until dirt is removed. If the headlamp has been contaminated with salt water, flush the unit with fresh water and dry as described above.

Modes

The Vizz RGB has the following modes:

Mode Lumens Runtime Beam Pattern
High Spot 550 2.5h 0-20m
Low Spot 40-95 33-100h 0-25m
Red 3-5 40-55h N/A
Green 45 45h N/A
Blue 3 40h N/A
White 80% N/A N/A

Note : Runtime is defined as the duration of time from the initial light output value until the light output reaches 10% of the initial value using fresh batteries. Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux.

Vizz RGB MPLS Accessories

To attach the Vizz RGB Tactical MPLS to the NVG Shroud:

  1. Slide the bracket arm into the NVG Shroud adapter plate, making sure the pull tab is above the lip of the adapter plate and that the male grooves on the bottom of the bracket arm are aligned inside the female grooves on the bottom of the adapter plate.
  2. Push the bracket arm securely into place, ensuring that the pull tab audibly clicks over the lip of the NVG Shroud adapter plate.
  3. The MPLS Headlamp should now be secured in the NVG Shroud. You can rotate the headlamp to focus your light source accordingly.

To remove the MPLS headlamp from the NVG Shroud:

  1. Remove the NVG Mount from your helmet.
  2. Push up slightly on the bottom of the light housing.
  3. While pushing upward, use the tool on the provided headstrap to press the tab of the arm bracket towards the headlamp housing, so that it disengages from the NVG Shroud adapter plate.
  4. Slide the headlamp unit out of the NVG Shroud adapter plate.

Battery Installation

Princeton-Tec-VIZZ-RGB-MPLS-Helmet-Lights-FIG-
\(3\)

3 AAA

  • Alkaline (LR03)
  • Lithium (L92)
  • Rechargeable NiCad or NiMH

Princeton Tec cares about the environment and recommends recycling batteries. For more information about battery recycling, please go to https://batterysolutions.com
Observe proper battery polarity. Improper installation of the batteries will damage the light and void the warranty

WARNING!

  • Never mix fresh and used batteries.
  • Never mix different battery brands or chemistry types
  • Always remove drained batteries immediately.
  • Remove batteries during long periods of storage.

NOTE : Lithium batteries offer extended constant brightness time, extreme cold weather performance, and lighter weight. Rechargeable
NiCad or NiMH batteries may result in reduced brightness due to lower nominal voltage.

The Vizz RGB battery compartment has a waterproof seal. It is important to keep this seal free from dirt and away from harsh chemicals in order to preserve waterproof integrity. Inspect the seal every time batteries are changed. If dirt is present, wipe gently with a damp cotton swab and mild soap until dirt is removed

Switch Operation

Princeton-Tec-VIZZ-RGB-MPLS-Helmet-Lights-FIG-
\(4\)

From off:

  • Press 1x – Red
  • Press 2x – Green
  • Press 3x – Blue
  • Press 4x – Off
  • One Second Hold from any mode – White
  • Press & Hold while in white mode – Dimming
  • Press 1x after more than 1 second in any mode- Off
  • Five second hold – Lockout/Unlock

From off, 5 second hold will lock light to prevent accidental Activation and resulting battery drain. Removal and replacement of batteries will also reset Vizz RGB to unlocked state.

Troubleshooting

If the Vizz RGB fails to light:

  • Check the batteries for proper installation.
  • Replace batteries if proper installation is confirmed.
  • Check circuit board for water (the seal may have be compromised by improper rear cover installation or dirty seal). The light will resume normal operation once the water is shaken or blown out and the light isleft open until completely dry. If the light has been contaminated with salt water, flush the unit with fresh water and dry as described above

Vizz RGB MPLS Accessories

To attach the Vizz RGB Tactical MPLS to the NVG Shroud:

  1. Slide the bracket arm into the NVG Shroud adapter plate, makingsure the pull tab is above the lip of the adapter plate and that themale grooves on the bottom of the bracket arm are aligned insidethe female grooves on the bottom of the adapter plate.
  2. Push the bracket arm securely into place, ensuring that the pull tab audibly clicks over the lip of the NVG Shroud adapter plate.
  3. Your MPLS Headlamp should now be secured in the NVG Shroud. You can rotate the headlamp to focus your light source accordingly.

To remove the MPLS headlamp from the NVG Shroud:

  1. Remove the NVG Mount from your helmet.
  2. Push up slightly on the bottom of the light housing.
  3. While pushing upward, use the tool on the provided headstrap to press the tab of the arm bracket towards the headlamp housing, so that it disengages from the NVG Shroud adapter plate.
  4. Slide the headlamp unit out of the NVG Shroud adapter plate

To attach the MPLS Headlamp to the Butterfly Mount:

  1. Slide the bracket arm into the Butterfly Mount, making sure the pull tab is above the lip of the mount and that the male grooves on the bottom of the bracket arm are aligned inside the female grooves onthe bottom of the mount.
  2. Push the bracket arm securely into place, ensuring that the pull tab audibly clicks over the lip of the Butterfly Mount.
  3. Your MPLS Headlamp should now be secured in the Butterfly Mount. The mount can be attached to the provided headstrap, MOLLE straps, or any 1” webbing. You can rotate the headlamp to focus your light source accordingly.

To remove the MPLS headlamp from the Butterfly Mount:

  1. Push up slightly on the bottom of the light housing.
  2. While pushing upward, use the tool on the provided headstrap topress the tab of the arm bracket towards the headlamp housing, so that it disengages from the Butterfly Mount.
  3. Slide the headlamp unit out of the Butterfly Mount.

Performance

Princeton-Tec-VIZZ-RGB-MPLS-Helmet-Lights-FIG-
\(5\)

(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the point the device is first turned on— using fresh batteries, until the light output reaches 10% of the initial value. Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux

Mounting System

Princeton-Tec-VIZZ-RGB-MPLS-Helmet-Lights-FIG-
\(6\)

Warranty

USA Lifetime Warranty – International 10-YearWarranty

Due to International regulations, Princeton Tec’s lifetime warranty can only be offered to customers in the USA. Princeton Tec offers a 10-year warranty to our customers outside the USA. FULL WARRANTY – Princeton Tec warrants this product to be free from defects in workmanship and materials under normal use for as long as you own this product. This warranty covers all of the component parts of the product except batteries. This warranty does not cover deterioration due to normal wear or damage due to misuse, alteration, negligence, accidents, or unauthorized repair. Princeton Tec will repair or replace parts which are defective In workmanship or materials. Your authorized Princeton Tec Dealer and Princeton Tec are the only facilities authorized to repair the product. After (3) unsuccessful attempts to repair the product, you have the right to elect replacement of the product or a refund of the purchase price less allowance for use of the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
Princeton Tec reserves the right to change product specifications without notice.

FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a chemical known to the State of California to cause birth defects or other reproductive harm.

Return Policy
If your light fails to operate, follow these simple steps:

  1. Check batteries. Replace if necessary.
  2. To send your light in for repair or replacement, first contact Princeton Tec customer service on 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault you are experiencing. No warranty repairs will be accepted without an RMA number.
  3. Return the light without batteries to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be accepted.
  4. Upon receipt your light will be processed in about two weeks. Please allow additional time for return transportation from NJ.

Princeton Tec PO Box 8057, Trenton, NJ 08650
Phone: 609-298-9331
Fax : 609-298-9601
princetontec.com
© 2023 Princeton Tec

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Princeton Tec User Manuals

Related Manuals