AURA LIGHT PHOTON OPT7 RGB Rock Lights Instruction Manual
- June 13, 2024
- AURA LIGHT
Table of Contents
INSTRUCTION MANUAL
SPECIFICATIONS
| Input Voltage | DC 12V |
|---|---|
| Input Power | Max 9 Watts per pod |
| LED Color | 6pcs – RGB per pod |
| Raw Lumens | 1200 LM (8 Pods Combined) |
| Waterproof | IP68 |
| Operating Temperature | -5 ℉ – 120 ℉ |
MAIN COMPONENTS
REMOTE CONTROL
- Power-ON
- Automatic Color Change
- Power-OFF
- Speed +/- 8 Levels
- Mode +/- 19 Mode
- Dimmer 8 Levels
- Color Selection 12 Colors
WHERE TO INSTALL
Recommended locations for Rock Light Pods
3 WAYS TO MOUNT THE ROCK LIGHT POD
STEP 1
There are 3 installation methods for you to choose, you can refer to the
following methods to install.
| OPTION 1 | Use “Strong Magnets” for mounting as shown in Fig. 1 |
|---|---|
| OPTION 2 | Use “Self-Drilling Screws” for mounting as shown in Fig. 2 |
| OPTION 3 | Use “VHB Double-Sided Adhesive” for mounting as shown in Fig. 3 |
IMPORTANT: Before starting installation ,we recommend that all rock light
pods be checked to ensure that all functions are working properly.
STEP 2
Designate your mounting locations for each Rock Light Pods and the Control
Box. (Refer to Page 3 for RECOMMENDED MOUNTING LOCATIONS)
IMPORTANT: Avoid hot surfaces and / or moving parts.
STEP 3
Start installing the LED Pods onto your vehicle. If any excess wiring are
exposed during installation process, you must use the zip-ties to securely tie
them together and tuck the wire into the junction area to avoid snagging or
damage wires.
STEP 4
Once the pods and wires are all safely installed onto your vehicle, you can
now begin to use your Photons!
Feel free to share a review along with a photo of installations so others
users like yourself can enjoy the OPT7 Off-Road too! Rock on!
CAUTION
Rock Light Pods become extremely hot during use-keep away from any vehicle
parts that may be damaged by exposure to high temperatures.
HOW TO INSTALL THE CONTROL BOX
STEP 1
As show below, connect all the Rock Light Pods to the control box with the
included extension wires.
CAUTION Avoid installation areas of the engine bay + heated surfaces.
IMPORTANT
BE SURE TO CONFIRM THE CORRECT DIRECTION OF THE ARROW!!
TO AVOID PRODUCT DAMAGE DUE TO INCORRECT INSTALLATION.
CORRECT INSTALLATION
STEP 2
Find a constant 12-volt power source to power the rock lights. For details
refer to the instructions below:
- Connect the positive(+) wire to the positive post (+) of the battery.
- Connect the negative(-) wire to the negative post (-) of the battery or to a common Ground location.
WARNING
- Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10AMPs or less!!
- Please ensure that the LED bars or strips/control box/wiring all are mounted in areas where will not exceed 85℃ or 185 ℉.
**** If you are uncomfortable performing work of this nature yourself, then do not hesitate to consult a professional for help. Working with a vehicle’s electrical system can be hazardous to an unqualified individual. OPT7 is not liable for damages or personal injuries while installing this product. The installation guide is provided as assistance to reduce set up time.
DISCLAIMER
OPT7 Lighting is not liable for damages or personal injuries while installing
this product. The Installation Guide is intended as assistance to reduce setup
time.
OPT7 Lighting assumes no responsibility for improper installation. If you are
unfamiliar with your vehicle or inexperienced with aftermarket upgrades,
please seek professional assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>