Princeton Tec RMX300-RGB-BK Remix RGB Headlamp Instruction Manual
- June 6, 2024
- Princeton Tec
Table of Contents
Princeton Tec RMX300-RGB-BK Remix RGB Headlamp Instruction Manual
Battery Installation –See Battery Installation Diagram
- 3 AAA
- Alkaline (LR03)
- Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and recommends recycling batteries.
For more information about battery recycling, please go to:
www.batteryrecycling.com
To install the batteries, unlatch the battery door. Open the Remix case by
popping the door latch over the catch and rotate the door open.
Install three AAA batteries according to the polarity markings on the inside
of the cabinet. Observe proper battery polarity when installing the batteries.
Improper installation of the batteries will damage the light and void the
warranty.
Rotate the door to the closed position, squeeze the body between your
forefingers and thumb to snap the door latch over the catch.
Battery Replacement
WARNING
- Never mix fresh and used batteries.
- Never mix different battery brands or chemistry types.
- Always remove drained batteries immediately.
- Remove batteries during long periods of storage.
NOTE : Rechargeable NiCad or NiMH batteries may result in reduced brightness due to lower nominal voltage.
Switch Operation – See Switch Operation diagram
The Remix has two light sources to choose from: three Ultrabright LEDs and one
Maxbright LED. The Ultrabright LEDs have one level in each of three color
modes: red, green and blue. The white Maxbright LED has two modes (Low and
High).
The first press will turn the light on in red mode. A subsequent press within
1.6 seconds changes to green, and another press within 1.6 seconds changes to
blue. To activate the Maxbright LED, press and hold the button down until the
light turns on in low mode. Another press within 1.6 seconds will change to
high level.
NOTE : If you keep the button pressed the light will continue to switch
back and forth between the 5mm and Maxbright LED until you release the button.
Any button press after two seconds will turn the light off.
One final note about the light function – If you have the light turned on,
(and more than 1.6 seconds has passed since your last button press) and you
press and hold the button down to switch light sources, you will be in
darkness for about one second as the light sees this press as a signal to turn
the light off and switch to the other light source simultaneously.
The times listed on the rear of the package assume that you start with fresh
batteries and use only one mode.
Switch Operation**
To switch between light sources, press and hold button (1-2 seconds)
Princeton Tec calculates total burn time as the time it takes for the light
source to produce a minimum of 0.25 lux at 2 meters. 0.25 lux is about the
equivalent of a full moon on a clear night.
Troubleshooting
If the Remix fails to light:
- Check the batteries for proper installation.
- Replace batteries if proper installation is confirmed.
- Check the light for water contamination on the circuit board. The light will resume normal operation once the water is shaken or blown out and the light is left open until completely dry. If the light has been contaminated with salt water, flush the unit with fresh water and dry as described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free from defects in
workmanship and materials under normal use for 5 years. This warranty covers
all of the component parts of the product except batteries.
This warranty does not cover deterioration due to normal wear or damage due to
misuse, alteration, negligence, accidents, or unauthorized repair.
Princeton Tec will repair or replace parts which are defective in workmanship
or materials.
After (3) unsuccessful attempts (within the warranty period) to repair the
product, you have the right to elect replacement of the product or a refund of
the purchase price less allowance for use of the product. NO INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some states do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.) This warranty gives
you specific legal rights, and you may also have other rights which vary from
state to state.
Princeton Tec reserves the right to change product specifications without
notice.
FOR CALIFORNIA RESIDENTS:
WARNING : This product contains Bisphenol A (BpA) a chemical known to the
State of California to cause birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
- Check batteries. Replace if necessary.
- To send your light in for repair or replacement, first contact Princeton Tec customer service at 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault your are experiencing. No warranty repairs will be accepted without an RMA number.
- Return the light to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be accepted.
- Upon receipt your light will be processed in about two weeks. Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2017 Princeton Tec