SUNSKY D1 Car Head Up Display Instruction Manual

SUNSKY D1 Car Head Up Display Instruction Manual

This product Design Patent and Display Images Copyright had been registered with customs record

Product Introduction

HUD short for Head Up Display, the main function is to reflect the car dashboard information (e.g. speed, RPM, water temperature ,voltage ,trip distance etc),and keep the driver eyes always on road to avoid the dangerous of lowering down head to read the instrument.

Special Reminder

The working voltage of this product: 5V~18Vdc (12Vdc/200mA) . This product is a dual system: Users can freely choose the mode. When the OBD system is not compatible, please switch to the GPS system and plug with the USB cable.

Product function:

1. Multi-function area: RPM, water temperature, voltage, fuel consumption, altitude, driving distance, navigation distance point, driving time, power test, number of satellites, clock
2. RPM=Rotating speed, TRIP=driving distance, MIN=driving minute, LHK=fuel consumption, ASL=altitude, a + =100km acceleration, °C/F=water temperature
3. RPM icon
4. Speed icon
5. System icon, Fault code icon
6. Compass (display navigation info when navigating),after the satellite is finding ,the GPS light stops flashing and stays on for normal use. When the vehicle speed >5KM/H, display the driving direction: N = North S = South W =West E =East NW =Northwest SW =Southwest SE =Southeast NE =Northeast
7. Lane display: Display the lane of the vehicle according to the navigation APP in your phone.
8. Camera icon
9. Light sensor: HUD can automatically adjust the brightness according to the environment
10. Speed unit: KM/H=Kilometre/hour, MPH=Mile/hour
11. Display Voltage, Navigation distance, Number of satellites
12. V= Voltage, KM=Navigation distance, GPS=Number of satellites

Button functions

1. OBD connector/USB connector
2. Scroll button (can pull up, pull down, short press in, long press in)
3. System selection Button

Scroll button (on the left)

1. Vertical short press (quick press and release within 1 second):
   (1) to switch the display mode
   (2) to choose menu after entering the setup menu

2. Vertical long press (press in the button >2s and release):
   (1) to enter the setting menu(Item1-14)
   (2) to save and exit after setting

3. Pull up:
   (1) switch and display the yellow 8888 interface
   (2) move the option after entering the setting

4. Pull down:
   (1) switch and display the blue 888 interface
   (2) move the option after entering the setting

5. Turn on/off the buzzer
   Pull up the scroll for 2s to turn off the buzzer(three beeps), again to turn on the buzzer(two beeps)

System selection

Pull up the System selection Button to enter the OBD system mode, pull down to enter the GPS system mode

OBD System

(For OBD2 car)

Function: vehicle speed, RPM, fuel consumption, water temperature, voltage, clock, driving mileage, driving time, driving direction, altitude, number of satellites, RPM icon

GPS System

(For all car)
Function: vehicle speed, time, voltage, driving time, driving distance, driving direction, altitude, number of satellites, speed icon

When the OBD system is not compatible, please pull down the system selection button to switch to the GPS system and plug with the USB cable

GPS system use

GPS flashing is in the state of searching for stars. Please move the car to an open road. After the satellite is finding, the GPS light stops flashing and stays on for normal use.

Restore setting:

Unplug the power, vertical long press the scroll button and don’t release it, plug in the power and release the scroll button after the screen is fully lit.

Clear the fault codes

After the OBD system is displayed normally, pull up the scroll button for 2 seconds and the screen is all on, pull down again for 2 seconds to clear the fault code

How to use Navigation

Please connect HUD with your smart-phone by Bluetooth, then APP can display a synchronized navigation information, compatible intelligent phones which meet the following requirement(Android 4.0 and IOS iPhone 5 or ) Android Phones: Please search keyword ‘WiiYii’ in the Android Market iPhone: Please search keyword ‘WiiYii’ in the APP Store Scan below QR code to download

https://play.google.com/store/apps/details?id=com.weiying.smartnavihttps://apps.apple.com/cn/app/wiiyii/id1495170499

1. Please download this software, install HUD and actuate your car, manually turn on the Bluetooth and positioned, click the icon of WiiYii, system will automatically search the Bluetooth and connect
2. If the mobile phone cannot connect to the Bluetooth device correctly, please follow the instructions below: HUD needs to be displayed normally. If the OBD system cannot be connected, please switch to the normal display of the GPS system. Whether the mobile phone Bluetooth is connected to other devices, delete the paired Bluetooth device, and bind WYHUD
3. Turn off the Bluetooth and on again, or restart the phone (For more questions, please refer to the FAQ on the next page)

DTC Trouble Code Search

Search

OBD-II search powered by dot.report

Setting Mode(Menu mode)

Vehicle long press the scroll button for 2 seconds to enter the setting item, vehicle short press to select the menu(1-14), pull up to switch the parameter value, vehicle long press for 2 seconds to save and exit. (As shown below)

Remind warning:

Please disconnect the HUD if you don’t drive for more than a week. Generally speaking car battery’s standby time is 1 month, we kindly suggest you to unplug the OBD device when the car is not used for a long time due to different vehicle conditions.

OBD FAQ

1.No function is displayed, no power

Check whether the OBD cable is tight connection, pull down repeatedly to confirm, please try it on another car if still not workable, analysis if it is a cause from OBD diagnostic interface, if yes, please repair it and connect the device again.

2.Only the car voltage displays and be automatic power off after 30

second

1. This product is only available for OBDII and EOBD cars when it is in OBD2 mode
2. OBD2 is a car protocol (U.S.A Cars:2003 Other regions:2008)
3. This product OBD2 mode does not support OBD I and JOBD
4. Switch to the GPS system using the USB cable to display

3.Wrong operation leads to crashes

1. Are there other OBD devices on your car(parking sensor, TPMS, lock lift window, ELM27)
2. Had your car been modified and brushed(central navigation, electronic throttle controller, fixed speed cruise, reset the computer system, engine start stop, keyless entry or remote start will cause a crash, unplug other OBD devices, and do a factory reset (see the menu settings) Please switch to GPS system which should be connected with a USB cable.

4.Inaccurate speed

1. Please check that the unit is correct KM/mile MPH, (speed unit switch please refer to the settings : Item 9)
2. When the car leaves the factory, the manufacturer increases the speed displayed on the dashboard by 5-7%, and the international standard is based on the data from the trip computer.
3. Fine-tune the vehicle speed, such as the instrument display 100 Km/h, HUD display 105Km/h dial on the dial to adjust the parameter value to 102

5.Unclear in daytime with double shadow

There is a high-brightness reflective film

1. Wipe the glass clean
2. Spray a little water
3. Tear off protective film “1” and stick the reflective film on the windshield
4. Tear off protective film “2”

6.Automatic start-up will auto off when step the brake and hybrid cars

will turn off during driving.

Method one: Enter the menu item 11 and adjust the value to 1. (See the menu settings) Method two: Setting shutdown delay to 300 seconds on the item 12, so that it can turn off after 5 minutes

7.HUD cannot auto shut down

After the car engine stops, the RPM and speed on the machine can not be turned off, please enter the setting menu turn to item 11, set voltage to 13.2V or 13.5V, so that the car can be turn off after 3 minutes. (See the menu settings)

8.Shut down during driving after adjusting the voltage

After the voltage is set, if the machine is turned off during driving, it is recommended to adjust the value of the item 11 to 12.8V or 12.5V.

9.Shut down and restart

Indicates that the voltage is higher than the starting voltage 13.2V, enter the setting menu and switch to item 11, set voltage to 13.6-13.8V (the device can only be turned on after the vehicle voltage is higher than the setting voltage)

GPS FAQ

1.Nothing on the screen, no power

Check if the USB interface has power or the connection is loose, pull it out and plug it in again several times, or replace the USB cable

2.No speed

The GPS is flashing to search for stars. Please move the car to an open road. After the satellite is found, the GPS light will be on and off, and it can be used normally.

3.Can not automatically turn on or turn off repeatedly during driving

When the OBD line is connected: the device will shutdown once the voltage is <13.2V for 3 minutes. Vehicle long press the scroll button for 5s to enter item 11 of the setting menu, and adjust the parameter value voltage to 13.0V or 12.8V

4.Inaccurate speed

1. Check whether the unit is correct, kilometres KM/mile MPH(switch the speed unit on the item 9)
2. When the car leaves the factory, the manufacturer increases the speed displayed on the dashboard by 5-7%. International standards are based on satellite data.
3. Fine-tune the vehicle speed, such as the instrument display 100 Km/h HUD display 105Km/h dial on the dial to adjust the parameter value to 102

5 The speed is stuck and does not work during driving

The power supply of the USB power cord is <5V, please use an OBD cable for power supply

6.Wrong driving direction or random jump

It will be normal until >5KM/H

7.Speed is still on after the car stops

Underground parking lots, tunnels, and overpasses, when there are obstructions, the signal will be unstable. Satellites will drift. Please drive to an open road. If the number of satellites found is more than 5, it will be normal.

8.Check the number of satellites

Pull down the scroll button to switch to the GPS icon ( more than 5 satellites can be displayed normally)

9.Cannot automatically turn off after the car shutdown

When the OBD cable is connected, the HUD will automatically shut down after 3 minutes If the machine is not turned off after 5 minutes after stopping the flame, adjust the voltage setting parameter value of item 11 to 13.5V ( (See the menu settings).

Navigation FAQ

1. Install APP

Scan QR code to download this APP(see manual) iPhone: Search keyword WiiYii’ in APP Store Android phones: Search keywordWiiYii’ in Android Market

1. Please download this software
2. Manually turn on the Bluetooth and location
3. Click the icon of WiiYii, system will automatically search the Bluetooth and connect

2.Use APP:

1. After installing the APP software correctly,
2. [1]Turn on Bluetooth on the mobile phone [2]Turn on location services [3]Turn on network
3. Click the WiiYii APP, the system will automatically search for Bluetooth devices and connect

3.APP Bluetooth connection is not successful

1. The HUD needs to display normally
2. Whether the Bluetooth of the mobile phone is connected to other devices, delete the paired Bluetooth devices, and then bind WYHUD Turn off Bluetooth again and turn on the phone Bluetooth, or restart the phone
3. Make sure that other phones turn off Bluetooth

4.Phone cannot search for WiiYii APP

1. Check the phone system version and whether it supports Bluetooth 4.0, Apple system IOS9 or above, Android 4.4 or above
2. Need mobile phone to search for WYHUD via Bluetooth, open your network
3. Turn on GPS navigation positioning, you can enter the navigation address after successful positioning

5.App Bluetooth connection is successful, no display of input address

Please turn on the location service, open your network, check the signal, please move to a place which has a strong signal, and enter the address again

6.HUD stuck during navigation or when you switch the display interface,

speed display is normal

Turn off the power-saving mode of the phone, turn off the screen forbidden function, or click to enter the phone navigation page and stay on the phone navigation page

7.Navigation is 10-20 meters away from the indication point

Since the GPS positioning error is about 5-10 meters, it is normal for the satellite signal to be 10-20 meters when the signal is weak.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>